scholarly journals Mesoscopic evolution of molten pool during selective laser melting of superalloy Inconel 738 at elevating preheating temperature

2021 ◽  
pp. 110355
Author(s):  
Weihao Wang ◽  
Wenhun Lin ◽  
Rui Yang ◽  
Yingna Wu ◽  
Jiapeng Li ◽  
...  
Keyword(s):  
Selective Laser Melting ◽  
Molten Pool ◽  
Laser Melting ◽  
Preheating Temperature

scholarly journals Effect of Process Parameters and High-Temperature Preheating on Residual Stress and Relative Density of Ti6Al4V Processed by Selective Laser Melting

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 930 ◽  
Author(s):  
Martin Malý ◽  
Christian Höller ◽  
Mateusz Skalon ◽  
Benjamin Meier ◽  
Daniel Koutný ◽  
...  
Keyword(s):  
Residual Stress ◽  
High Temperature ◽  
Residual Stresses ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Stress Reduction ◽  
Laser Melting ◽  
Preheating Temperature ◽  
Laser Velocity

The aim of this study is to observe the effect of process parameters on residual stresses and relative density of Ti6Al4V samples produced by Selective Laser Melting. The investigated parameters were hatch laser power, hatch laser velocity, border laser velocity, high-temperature preheating and time delay. Residual stresses were evaluated by the bridge curvature method and relative density by the optical method. The effect of the observed process parameters was estimated by the design of experiment and surface response methods. It was found that for an effective residual stress reduction, the high preheating temperature was the most significant parameter. High preheating temperature also increased the relative density but caused changes in the chemical composition of Ti6Al4V unmelted powder. Chemical analysis proved that after one build job with high preheating temperature, oxygen and hydrogen content exceeded the ASTM B348 limits for Grade 5 titanium.

scholarly journals Investigation on Selective Laser Melting AlSi10Mg Cellular Lattice Strut: Molten Pool Morphology, Surface Roughness and Dimensional Accuracy

Materials ◽  
2018 ◽  
Vol 11 (3) ◽  
pp. 392 ◽  
Author(s):  
Xuesong Han ◽  
Haihong Zhu ◽  
Xiaojia Nie ◽  
Guoqing Wang ◽  
Xiaoyan Zeng
Keyword(s):  
Surface Roughness ◽  
Selective Laser Melting ◽  
Molten Pool ◽  
Dimensional Accuracy ◽  
Laser Melting

scholarly journals The Influence of Process Parameters and Scanning Strategy on Lower Surface Quality of TA15 Parts Fabricated by Selective Laser Melting

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1228
Author(s):  
Junjie Jiang ◽  
Jianming Chen ◽  
Zhihao Ren ◽  
Zhongfa Mao ◽  
Xiangyu Ma ◽  
...  
Keyword(s):  
Surface Quality ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Flexible Manufacturing ◽  
Molten Pool ◽  
Lower Surface ◽  
Laser Melting ◽  
Scanning Strategy ◽  
Influence Of Process Parameters

With superior flexible manufacturing capability, selective laser melting (SLM) has attracted more and more attention in the aerospace, medical, and automotive industries. However, the poor quality of the lower surface in overhanging structures is still one of the factors that limits the wide application of SLM. In this work, the influence of process parameters and scanning strategy on the lower surface quality of SLMed TA15 (Ti-6Al-2Zr-1Mo-1V) titanium alloy parts were studied. The results showed that the laser surface energy density (EF) had a significant influence on the quality of the lower surface. Excessive EF led to obvious sinking of the molten pool and a serious slag hanging phenomenon. However, the too low EF easily contributed to the insufficient powder fusion in the lower surface area, which led to the agglomeration of a molten pool during core processing, resulting in slag hanging, pores, and powder spalling that reduced the quality of the lower surface. Moreover, the cross-remelting strategy and non-remelting strategy gained better surface quality at the low EF and high EF, respectively. In addition, it was found that the quality of the lower surface could be quickly and accurately evaluated by the cooling time of the molten pool during the processing of the lower surface. This research can increase the understanding of the forming mechanism of the lower surface and has certain guiding significance for the process optimization of the lower surface.

scholarly journals Numerical Simulation of Moving Heat Flux during Selective Laser Melting of AlSi25 Alloy Powder

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 877
Author(s):  
Cong Ma ◽  
Xianshun Wei ◽  
Biao Yan ◽  
Pengfei Yan
Keyword(s):  
Numerical Simulation ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Molten Pool ◽  
Laser Power ◽  
Scanning Speed ◽  
Powder Layer ◽  
Maximum Temperature ◽  
Three Dimensional Model ◽  
Laser Melting

A single-layer three-dimensional model was created to simulate multi-channel scanning of AlSi25 powder in selective laser melting (SLM) by the finite element method. Thermal behaviors of laser power and scanning speed in the procedure of SLM AlSi25 powder were studied. With the increase of laser power, the maximum temperature, size and cooling rate of the molten pool increase, while the scanning speed decreases. For an expected SLM process, a perfect molten pool can be generated using process parameters of laser power of 180 W and a scanning speed of 200 mm/s. The pool is greater than the width of the scanning interval, the depth of the molten pool is close to scan powder layer thickness, the temperature of the molten pool is higher than the melting point temperature of the powder and the parameters of the width and depth are the highest. To confirm the accuracy of the simulation results of forecasting excellent process parameters, the SLM experiment of forming AlSi25 powder was carried out. The surface morphology of the printed sample is intact without holes and defects, and a satisfactory metallurgical bond between adjacent scanning channels and adjacent scanning layers was achieved. Therefore, the development of numerical simulation in this paper provides an effective method to obtain the best process parameters, which can be used as a choice to further improve SLM process parameters. In the future, metallographic technology can also be implemented to obtain the width-to-depth ratio of the SLM sample molten pool, enhancing the connection between experiment and theory.

Surface Formation Mechanisms in Selective Laser Melting of Cobalt-Chromium-Molybdenum Powder

2020 ◽  
Vol 839 ◽  
pp. 73-78
Author(s):  
Alexander A. Saprykin ◽  
Yuriy P. Sharkeev ◽  
Natalya A. Saprykina ◽  
Egor A. Ibragimov
Keyword(s):  
Selective Laser Melting ◽  
Marangoni Effect ◽  
Powdered Material ◽  
Formation Mechanisms ◽  
Cobalt Chromium ◽  
Laser Melting ◽  
Movement Velocity ◽  
Surface Formation ◽  
Preheating Temperature ◽  
Cobalt Chromium Molybdenum

Selective laser melting (SLM) is a manufacturing technology of metal parts of any shapes with target mechanical properties by means of laser melting. This paper discusses the effect of SLM parameters: laser output power, laser movement velocity, scanning pitch and preheating temperature of a powdered material on surface formation mechanism, namely, its physical configuration when melting cobalt-chromium-molybdenum powdered material Со28Cr3Mo. The study points at structural differences of melted surfaces even under identical process parameters. Several types of surface formation are identified, e.g. homogenous melt, coagulated particles, and shapeless particles. Vapor pressure, Marangoni effect, and heat effect of a melted powder are stated to be key reasons for rough surface. This research is of high importance for understanding the effect of SLM parameters on formation of a target quality surface, positive stability and repeatable accuracy of the process.

Sign in / Sign up

Export Citation Format

Share Document