Mn doped Ni-Zn ferrite thick film as a highly selective and sensitive gas sensor for Cl2 gas with quick response and recovery time

Author(s):  
Prajyoti P. Gauns Dessai ◽  
Ashutosh Kumar Singh ◽  
V.M.S. Verenkar
Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 623
Author(s):  
Monika Gupta ◽  
Huzein Fahmi Hawari ◽  
Pradeep Kumar ◽  
Zainal Arif Burhanudin ◽  
Nelson Tansu

The demand for carbon dioxide (CO2) gas detection is increasing nowadays. However, its fast detection at room temperature (RT) is a major challenge. Graphene is found to be the most promising sensing material for RT detection, owing to its high surface area and electrical conductivity. In this work, we report a highly edge functionalized chemically synthesized reduced graphene oxide (rGO) thin films to achieve fast sensing response for CO2 gas at room temperature. The high amount of edge functional groups is prominent for the sorption of CO2 molecules. Initially, rGO is synthesized by reduction of GO using ascorbic acid (AA) as a reducing agent. Three different concentrations of rGO are prepared using three AA concentrations (25, 50, and 100 mg) to optimize the material properties such as functional groups and conductivity. Thin films of three different AA reduced rGO suspensions (AArGO25, AArGO50, AArGO100) are developed and later analyzed using standard FTIR, XRD, Raman, XPS, TEM, SEM, and four-point probe measurement techniques. We find that the highest edge functionality is achieved by the AArGO25 sample with a conductivity of ~1389 S/cm. The functionalized AArGO25 gas sensor shows recordable high sensing properties (response and recovery time) with good repeatability for CO2 at room temperature at 500 ppm and 50 ppm. Short response and recovery time of ~26 s and ~10 s, respectively, are achieved for 500 ppm CO2 gas with the sensitivity of ~50 Hz/µg. We believe that a highly functionalized AArGO CO2 gas sensor could be applicable for enhanced oil recovery, industrial and domestic safety applications.


2021 ◽  
pp. 2151043
Author(s):  
Zijing Wang ◽  
Fen Wang ◽  
Angga Hermawan ◽  
Jianfeng Zhu ◽  
Shu Yin

Porous nitrogen-doped Ti3C2T[Formula: see text] MXene (N-TCT) with a three-dimensional network structure is synthesized via a simple sacrifice template method and then utilized as an acetone gas sensor. By introducing nitrogen atoms as heteroatoms into Ti3C2T[Formula: see text] nanosheets, some defects generate around the doped nitrogen atoms, which can greatly improve the surface hydrophilicity and adsorption capacity of Ti3C2T[Formula: see text] Mxene nanosheets. It resulted in the enhanced gas sensitivity, achieving a response value of about 36 ([Formula: see text]/[Formula: see text] × 100%) and excellent recovery time (9s) at 150[Formula: see text]C. Compared with the pure Ti3C2T[Formula: see text]-based gas sensor (381/92s), the response and recovery time are both obviously improved, and the response value increased by 3.5 times. The gas-sensing mechanism of the porous N-TCT is also discussed in detail. Based on the excellent gas sensitivity of porous N-TCT for highly responsive acetone detection at high temperatures, the strategy of nitrogen-doped two-dimensional nanomaterials can be extended to other nanomaterials to realize their potential applications.


2018 ◽  
Vol 81 (1) ◽  
pp. 10101 ◽  
Author(s):  
Sonik Bhatia ◽  
Neha Verma ◽  
Munish Aggarwal

Nowadays, for environmental protection, the use of portable gas sensor is essential to detect toxic gases. To control this problem of hazardous gases, metal oxide based sensors plays a vital role. In this recent study, Indium (2 at.wt.%) doped ZnO films has been prepared by sol gel spin coating and thermal evaporation techniques on glass substrates. To enhance the sensing properties, indium (In) was used as dopant and their annealing effect of temperature was observed. Thermal properties have shown the fruitful result that prepared films are useful for the fabrication of solar cell. Electrical properties revealed that capacitance and dielectric constant decreases with increase in frequency. X-ray Diffraction showed hexagonal wurtzite structure highly oriented along (1 0 1) plane. Field emission scanning electron microscope of these synthesis films prepared by different have shown the morphology as nanospheres having size of the order of 40–60 nm. 2.0 at.% of indium as modifier resulted in highest response and selectivity towards 5 ppm of NO2 gas at different operating temperature (50–200 °C). Highest sensitivity was obtained at operating temperature of 150 °C. Prepared films have quick response and recovery time in the range of 14–27 s and 67–63 s. The highest response and recovery time of gas sensor was explained by valence ion mechanism.


2021 ◽  
Vol 21 (4) ◽  
pp. 2495-2499
Author(s):  
Hoang Si Hong ◽  
Tran Vinh Hoang

We developed a novel sensor structure by synthesizing Pd nanocubes (NCs) decorated on ZnO nanostructures (NSs) applied to resistive-type H2 gas sensor with micro-length in sensing channel. The ZnO NSs were selectively grown between micro-size finger-like interdigital electrodes through microelectromechanical technology. The novel H2 sensor structure with the sensing channel was reduced to micro-size by this proposed method to obtain a sensor with fast response/recovery time. The as-prepared structure exhibited robust sensing performance with a response of 11% at optimal temperature of 150 °C, good linearity, and fast response/recovery time within 10 s. The speed of chemisorption through the diffusion pathway in Pd NCs combined with micro-length in sensing channel in sensor showed fast response and recovery times of 9 and 15 s, respectively, toward 10,000 ppm (1%) H2 at 150 °C. The result showed approximate linearity response in H2 concentration range of 5÷10,000 ppm and a large operating temperature range from room temperature to 200 °C.


Chemosensors ◽  
2019 ◽  
Vol 7 (4) ◽  
pp. 52 ◽  
Author(s):  
Tatiana N. Myasoedova ◽  
Mikhail N. Grigoryev ◽  
Nina K. Plugotarenko ◽  
Tatiana S. Mikhailova

In this study, we designed two types of gas-sensor chips with silicon–carbon film, doped with CuO, as the sensitive layer. The first type of gas-sensor chip consists of an Al2O3 substrate with a conductive chromium sublayer of ~10 nm thickness and 200 Ω/□ surface resistance, deposited by magnetron sputtering. The second type was fabricated via the electrochemical deposition of a silicon–carbon film onto a dielectric substrate with copper electrodes formed by photoelectrochemical etching. The gas sensors are sensitive to the presence of CO and CH4 impurities in the air at operating temperatures above 150 °C, and demonstrated p- (type-1) and n-type (type-2) conductivity. The type-1 gas sensor showed fast response and recovery time but low sensitivity, while the type-2 sensor was characterized by high sensitivity but longer response and recovery time. The silicon–carbon films were characterized by the presence of the hexagonal 6H SiC polytype with the impurities of the rhombohedral 15 R SiC phase. XRD analysis revealed the presence of a CuO phase.


2011 ◽  
Vol 383-390 ◽  
pp. 6856-6860
Author(s):  
Xin Liu

A gas sensor based on MEMS (microelectro-machine system) has been developed to provide a sensitive means of detecting nitrogen dioxide. The structure, configuration and fabrication steps were described. The sensor was copper phthalocyanine (CuPc) films which caused a resistance change upon exposure to nitrogen dioxide. The sensor demonstrated a good response and recovery time about 4s and 7s separately. Results also indicate to be accordance with the sensitive mechanism of CuPc in terms of semiconductor theory.


Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 2882 ◽  
Author(s):  
Furu Zhong ◽  
Zhaofeng Wu ◽  
Jixi Guo ◽  
Dianzeng Jia

Novel Ni-doped wurtzite ZnS nanospheres decorated with Au nanoparticles (Au NPs–ZnS NSs) have been successfully fabricated using a simple method involving vacuum evaporation followed by an annealing process. This transition metal-doped gas sensor had high responsivity, extremely fast response and recovery time, and excellent selectivity to formaldehyde at room temperature. The response and recovery time are only 29 s and 2 s, respectively. Since ZnS is transformed into ZnO at a high temperature, superior room temperature-sensing performance can improve the stability and service life of the sensor. The improvement in sensing performance could be attributed to the reduced charge-transfer distance resulting from the creation of a local charge reservoir layer, and the catalytic and spillover effect of Au nanoparticles. The rough and porous spherical structure can also facilitate the detection and diffusion of gases. The as-prepared Au NPs–ZnS NSs are considered to be an extremely promising candidate material for gas sensors, and are expected to have other potential applications in the future.


2011 ◽  
Vol 131 (7) ◽  
pp. 484-489 ◽  
Author(s):  
Shinya Okazaki ◽  
Asako Takeuchi ◽  
Akihiro Takeshima ◽  
Makoto Sonehara ◽  
Toshiro Sato ◽  
...  
Keyword(s):  

2020 ◽  
Author(s):  
Amit Gupta ◽  
Santharaman Kannan ◽  
G. F. Harish Reddy
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document