Corrosion and mechanical behavior of plasma nitrated metallic biomaterial surfaces

2021 ◽  
Author(s):  
S.P. Venkatesan ◽  
Jeya Jeevahan ◽  
M. Purusothaman ◽  
S. Venkatesh ◽  
M. Rakesh Vimal
Keyword(s):  
Mechanical Behavior ◽  
Biomaterial Surfaces ◽  
Metallic Biomaterial

Microstructural and Dynamic Mechanical Characterization of Biodegradable Magnesium-Calcium Alloy for Orthopedic Implants

2014 ◽  
Author(s):  
V. S. Brooks ◽  
Y. B. Guo
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Orthopedic Implants ◽  
Strain Rates ◽  
High Strain Rates ◽  
Static Compression ◽  
Metallic Biomaterial

Magnesium-Calcium (Mg-Ca) alloy is an emerging metallic biomaterial for manufacturing biodegradable orthopedic implants. However, very few studies have been conducted on mechanical properties of the bi-phase Mg-Ca alloy, especially at the high strain rates often encountered in manufacturing processes. The mechanical properties are critical to design and manufacturing of Mg-Ca implants. The objective of this study is to study the microstructural and mechanical properties of Mg-Ca0.8 (wt %) alloy. Both elastic and plastic behaviors of the Mg-Ca0.8 alloy were characterized at different strains and strain rates in quasi-static tension and compression testing as well as dynamic split-Hopkinson pressure bar (SHPB) testing. It has been shown that Young’s modulus of Mg-Ca0.8 alloy in quasi-static compression is much higher than those at high strain rates. Yield strength and ultimate strength of the material are very sensitive to strain rates and increase with strain rate in compression. Strain softening also occurs at large strains in dynamic compression. Furthermore, quasi-static mechanical behavior of the material in tension is very different from that in compression. The stress-strain data was repeatable with reasonable accuracy in both deformation modes. In addition, a set of material constants for the internal state variable plasticity model has been obtained to model the dynamical mechanical behavior of the novel metallic biomaterial.

Application of TEM to Deformation, Wear, and Fracture of Ceramics

1974 ◽  
Vol 32 ◽  
pp. 472-473
Author(s):  
B. J. Hockey
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Mechanical Behavior ◽  
Brittle Materials ◽  
High Temperature Strength ◽  
Wide Range ◽  
Corrosive Environments ◽  
Further Development

Ceramics, such as Al2O3 and SiC have numerous current and potential uses in applications where high temperature strength, hardness, and wear resistance are required often in corrosive environments. These materials are, however, highly anisotropic and brittle, so that their mechanical behavior is often unpredictable. The further development of these materials will require a better understanding of the basic mechanisms controlling deformation, wear, and fracture.The purpose of this talk is to describe applications of TEM to the study of the deformation, wear, and fracture of Al2O3. Similar studies are currently being conducted on SiC and the techniques involved should be applicable to a wide range of hard, brittle materials.

The influence of the addition of ground olive stone on the thermo-mechanical behavior of compressed earth blocks

2020 ◽  
Vol 108 (2) ◽  
pp. 203
Author(s):  
Samia Djadouf ◽  
Nasser Chelouah ◽  
Abdelkader Tahakourt
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Mechanical Behavior ◽  
Agricultural Waste ◽  
Hydraulic Press ◽  
Dry Density ◽  
Olive Stone ◽  
Compressed Earth Blocks ◽  
Clay Matrix ◽  
Earth Blocks

Sustainable development and environmental challenges incite to valorize local materials such as agricultural waste. In this context, a new ecological compressed earth blocks (CEBS) with addition of ground olive stone (GOS) was proposed. The GOS is added as partial clay replacement in different proportions. The main objective of this paper is to study the effect of GOS levels on the thermal properties and mechanical behavior of CEB. We proceeded to determining the optimal water content and equivalent wet density by compaction using a hydraulic press, at a pressure of 10 MPa. The maximum compressive strength is reached at 15% of the GOS. This percentage increases the mechanical properties by 19.66%, and decreases the thermal conductivity by 37.63%. These results are due to the optimal water responsible for the consolidation and compactness of the clay matrix. The substitution up to 30% of GOS shows a decrease of compressive strength and thermal conductivity by about 38.38% and 50.64% respectively. The decrease in dry density and thermal conductivity is related to the content of GOS, which is composed of organic and porous fibers. The GOS seems promising for improving the thermo-mechanical characteristics of CEB and which can also be used as reinforcement in CEBS.

Sign in / Sign up

Export Citation Format

Share Document