scholarly journals Evaluation of Chip-tool Interface Temperature: Effect of Tool Coating and Cutting Parameters during Turning Hardened AISI 4340 Steel

2014 ◽  
Vol 6 ◽  
pp. 996-1005 ◽  
Author(s):  
Satish Chinchanikar ◽  
S.K. Choudhury
Keyword(s):  
Temperature Effect ◽  
Cutting Parameters ◽  
Interface Temperature ◽  
Aisi 4340 Steel ◽  
4340 Steel ◽  
Tool Coating ◽  
Aisi 4340

scholarly journals VARIATION OF CUTTING PARAMETERS IN THE PROCESS OF TURNING AISI 4340 STEEL ON SURFACE ROUGHNESS

SINERGI ◽  
2019 ◽  
Vol 23 (2) ◽  
pp. 139
Author(s):  
M. Sobron Yamin Lubis ◽  
Erwin Siahaan ◽  
Steven Darmawan ◽  
Adianto Adianto ◽  
Ronald Ronald
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Aisi 4340 Steel ◽  
4340 Steel ◽  
Metal Machining ◽  
Aisi 4340

In the metal machining process, cutting speed and feed rate are cutting parameters that affect the surface quality of the workpiece produced. The use of improper cutting parameters can cause the workpiece surface to be rough, and the cutting toolage to be shorter. This study was conducted to determine the effect of cutting parameters and the use of carbide tools on the surface roughness of metal steel workpieces. The research was carried out using the experimental method of AISI 4340 steel metal workpiece turning using cutting tool coated. Five variations of cutting speed used are: 140 m/min, 150 m/min, 160 m/min, 170 m/min, 180 m/min and three variations in feed rate: 0.25 mm/rev, 0.3 mm/rev, 0.35 mm/rev. After the turning process, the surface roughness of the workpiece is measured using a surface tester. From the results of the study, it was found that the surface roughness value was directly proportional to the feed rate and inversely proportional to the cutting speed. The smallest surface roughness value is 9.56 μm on cutting speed 180 m / min, and feed rate is 0.25 mm/rev. 

scholarly journals Optimization of Dimensional Tolerances and Material Removal Rate in the Orthogonal Turning of AISI 4340 Steel

2021 ◽  
Author(s):  
Chathakudath Sukumaran Sumesh ◽  
Dawood Sheriff Akbar ◽  
Hari Shankar Purandharadass ◽  
Raghunandan J. Chandrasekaran
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Metal Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 4340 Steel ◽  
4340 Steel ◽  
Aisi 4340

Turning is one of the most used metal removal operations in the industry. It can remove material faster, giving reasonably good surface quality apart from geometrical requirements. Conformity of geometry is one of the most significant requirements of turned components to perform their intended functions. Apart from dimensional requirements, the important geometrical necessities are Circularity, Straightness, Cylindricity, Perpendicularity, etc. Since they have a direct influence on the functioning of the components, the effect of the cutting parameters on them has greater significance. In this paper experiments are carried out to examine the effect of turning parameters such as cutting speed, feed rate, and depth of cut on responses like; straightness, roundness, surface roughness, and material removal rate during turning of AISI 4340 steel. Analysis of Variance (ANOVA) is performed and the influence of parameters on each response is studied. The optimal values of parameters obtained from the study are further confirmed by conducting experiments.

Influence of Minimum Quantity Lubrication on Grinding Performance of Annealed AISI 4340 Steel

2017 ◽  
Vol 31 (2) ◽  
pp. 17 ◽  
Author(s):  
Sirsendu Mahata ◽  
Ankesh Samanta ◽  
Joydip Roy ◽  
Bijoy Mandal ◽  
Santanu Das
Keyword(s):  
Minimum Quantity Lubrication ◽  
Aisi 4340 Steel ◽  
Minimum Quantity ◽  
Grinding Performance ◽  
4340 Steel ◽  
Aisi 4340
Sign in / Sign up

Export Citation Format

Share Document