Flow-induced vibration and fretting-wear predictions of steam generator helical tubes

2008 ◽  
Vol 238 (4) ◽  
pp. 890-903 ◽  
Author(s):  
Jong Chull Jo ◽  
Myung Jo Jhung
Keyword(s):  
Steam Generator ◽  
Fretting Wear ◽  
Flow Induced Vibration ◽  
Helical Tubes

Vibration Excitation Forces in a Rotated Triangular Tube Bundle Subjected to Two-Phase Cross Flow

2010 ◽  
Author(s):  
H. Senez ◽  
N. W. Mureithi ◽  
M. J. Pettigrew
Keyword(s):  
Steam Generator ◽  
Tube Bundle ◽  
Cross Flow ◽  
Fretting Wear ◽  
Experimental Program ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Fluid Forces ◽  
Vibration Excitation

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting wear or fatigue. Detailed flow and vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. Studies on this subject have already been done, providing results on flow regimes, fluidelastic instabilities, and turbulence-induced vibration. The spectrum of turbulence-induced forces has usually been expected to be similar to that in single-phase flow. However, a recent study, using tubes with a diameter larger than that in a real steam generator, showed the existence of significant quasi-periodic forces in two-phase flow. An experimental program was undertaken with a rotated-triangular array of cylinders subjected to air-water cross-flow, to simulate two-phase mixtures. The tube bundle here has the same geometry as that of a real steam generator. The quasi-periodic forces have now also been observed in this tube bundle. The present work aims to understand turbulence-induced forces acting on the tube bundle, providing results on drag and lift force spectra and their behaviour according to flow parameters, and describing their correlations. Detailed experimental test results are presented in this paper. Comparison is also made with previous measurements with larger diameter tubes. The present results suggest that quasi-periodic fluid forces are not uncommon in tube arrays subjected to two-phase cross-flow.

Experimental Fretting-Wear Studies of Steam Generator Materials

1995 ◽  
Vol 117 (4) ◽  
pp. 312-320 ◽  
Author(s):  
N. J. Fisher ◽  
A. B. Chow ◽  
M. K. Weckwerth
Keyword(s):  
Steam Generator ◽  
Contact Force ◽  
Environmental Conditions ◽  
Analytical Techniques ◽  
Work Rate ◽  
Fretting Wear ◽  
Flow Induced Vibration ◽  
Dynamic Interactions ◽  
Support Materials ◽  
Wear Damage

Flow-induced vibration of steam generator tubes results in fretting-wear damage due to impacting and rubbing of the tubes against their supports. This damage can be predicted by computing tube response to flow-induced excitation forces using analytical techniques, and then relating this response to resultant wear damage using experimentally derived wear coefficients. Fretting-wear of steam generator materials has been studied experimentally at Chalk River Laboratories for two decades. Tests are conducted in machines that simulate steam generator environmental conditions and tube-to-support dynamic interactions. Different tube and support materials, tube-to-support clearances, and tube support geometries have been studied. The effect of environmental conditions, such as temperature, oxygen content, pH and chemistry control additive, have been investigated as well. Early studies showed that damage was related to contact force as long as other parameters, such as geometry and motion, were held constant. Later studies have shown that damage is related to a parameter called work-rate, which combines both contact force and sliding distance. Results of short and long-term fretting-wear tests for CANDU steam generator materials at realistic environmental conditions are presented. These results demonstrate that work-rate is an appropriate correlating parameter for impact-sliding interaction.

Probabilistic Assessment of Fretting Wear in Steam Generator Tubes Under Flow Induced Vibrations

2003 ◽  
Author(s):  
Greg D. Morandin ◽  
Richard G. Sauve´
Keyword(s):  
Steam Generator ◽  
Degradation Mechanism ◽  
Probabilistic Methods ◽  
Fretting Wear ◽  
Nonlinear Flow ◽  
Impact Wear ◽  
Steam Generators ◽  
Flow Induced Vibration ◽  
Wear Damage ◽  
The Impact

Successful life management of steam generators requires an ongoing operational assessment plan to monitor and address all potential degradation mechanisms. A degradation mechanism of concern is tube fretting as a result of flow-induced vibration. Flow induced vibration predictive methods routinely used for design purposes are based on deterministic nonlinear structural analysis techniques. In previous work, the authors have proposed the application of probabilistic techniques to better understand and assess the risk associated with operating power generating stations that have aging re-circulating steam generators. Probabilistic methods are better suited to address the variability of the parameters in operating steam generators, e.g., flow regime, support clearances, manufacturing tolerances, tube to support interactions, and material properties. In this work, an application of a Monte Carlo simulation to predict the propensity for fretting wear in an operating re-circulation steam generator is described. Tube wear damage is evaluated under steady-state conditions using two wear damage correlation models based on the tube-to-support impact force time histories and work rates obtained from nonlinear flow induced vibration analyses. Review of the tube motion in the supports and the impact/sliding criterion shows that significant tube damage at the U-bend supports is a result of impact wear. The results of this work provide the upper bound predictions of wear damage in the steam generators. The EPRI wear correlations for sliding wear and impact wear indicate good agreement with the observed damage and, given the preponderance of wear sites subject to impact, should form the basis of future predictions.

Time Domain Simulation of the Vibration of a Steam Generator Tube Subjected to Fluidelastic Forces Induced by Two-Phase Cross-Flow

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Téguewindé Sawadogo ◽  
Njuki Mureithi
Keyword(s):  
Steam Generator ◽  
Two Phase Flow ◽  
Work Rate ◽  
Fretting Wear ◽  
Phase Flow ◽  
Reference Case ◽  
Two Phase ◽  
Steam Generator Tube ◽  
Wide Range ◽  
Instability Regime

Having previously verified the quasi-steady model under two-phase flow laboratory conditions, the present work investigates the feasibility of practical application of the model to a prototypical steam generator (SG) tube subjected to a nonuniform two-phase flow. The SG tube vibration response and normal work-rate induced by tube-support interaction are computed for a range of flow conditions. Similar computations are performed using the Connors model as a reference case. In the quasi-steady model, the fluid forces are expressed in terms of the quasi-static drag and lift force coefficients and their derivatives. These forces have been measured in two-phase flow over a wide range of void fractions making it possible to model the effect of void fraction variation along the tube span. A full steam generator tube subjected to a nonuniform two-phase flow was considered in the simulations. The nonuniform flow distribution corresponds to that along a prototypical steam-generator tube based on thermal-hydraulic computations. Computation results show significant and important differences between the Connors model and the two-phase flow based quasi-steady model. While both models predict the occurrence of fluidelastic instability, the predicted pre-instability and post instability behavior is very different in the two models. The Connors model underestimates the flow-induced negative damping in the pre-instability regime and vastly overestimates it in the post instability velocity range. As a result the Connors model is found to underestimate the work-rate used in the fretting wear assessment at normal operating velocities, rendering the model potentially nonconservative under these practically important conditions. Above the critical velocity, this model largely overestimates the work-rate. The quasi-steady model on the other hand predicts a more moderately increasing work-rate with the flow velocity. The work-rates predicted by the model are found to be within the range of experimental results, giving further confidence to the predictive ability of the model. Finally, the two-phase flow based quasi-steady model shows that fluidelastic forces may reduce the effective tube damping in the pre-instability regime, leading to higher than expected work-rates at prototypical operating velocities.

A comparative study on the fretting wear of steam generator tubes in korean power plants

Wear ◽  
2003 ◽  
Vol 255 (7-12) ◽  
pp. 1198-1208 ◽  
Author(s):  
Young-Ho Lee ◽  
Hyung-Kyu Kim ◽  
Hong-Deok Kim ◽  
Chi-Yong Park ◽  
In-Sup Kim
Keyword(s):  
Comparative Study ◽  
Steam Generator ◽  
Power Plants ◽  
Fretting Wear ◽  
Steam Generator Tubes

Progress in studying the fretting wear/corrosion of nuclear steam generator tubes

2020 ◽  
Vol 144 ◽  
pp. 107556 ◽  
Author(s):  
Xianglong Guo ◽  
Ping Lai ◽  
Ling Li ◽  
Lichen Tang ◽  
Lefu Zhang
Keyword(s):  
Steam Generator ◽  
Fretting Wear ◽  
Steam Generator Tubes

Wear Transitions of Tube-Support Components for a Nuclear Steam Generator under Fretting Conditions

2006 ◽  
Vol 326-328 ◽  
pp. 1263-1266 ◽  
Author(s):  
Sung Hoon Jeong ◽  
Jung Min Park ◽  
Joong Hui Lee ◽  
Young Ze Lee
Keyword(s):  
Nuclear Power ◽  
Applied Load ◽  
Fluid Flows ◽  
Relative Displacement ◽  
Fretting Wear ◽  
Steam Generators ◽  
Flow Induced Vibration ◽  
Support Materials ◽  
Mild Wear ◽  
Inconel 690

Tubes in nuclear steam generators are held up by supports because the tubes are long and slender. Fluid flows of high-pressure and high-temperature in the tubes cause oscillating motions between tubes and supports. This is called as FIV (flow induced vibration), which causes fretting wear in contact parts of tube-support. The fretting wear of tube-support can threaten the safety of nuclear power plant. Therefore, a research about the fretting wear characteristics of tube-support is required. This work is focused on fretting wear transitions from mild wear to severe wear of tube-support materials by various loads and relative displacements. The transition is defined on the basis of the changes in wear amount. To investigate the transition, the fretting wear tester was contrived to prevent the reduction of relative displacement between tube and support by increasing the load. The tube and support materials were Inconel 690 and 409 SS, respectively. The results show that the transition of tube-support wear is caused by the changes of the dominant wear mechanism depending on the applied load and the relative displacement.

Flow-Induced Vibration Responses of U-Tube Bundle in Air-Water Flow

2007 ◽  
Author(s):  
In-Cheol Chu ◽  
Heung June Chung ◽  
Chang Hee Lee ◽  
Hyung Hyun Byun ◽  
Moo Yong Kim
Keyword(s):  
Steam Generator ◽  
Two Phase Flow ◽  
Tube Bundle ◽  
Damping Ratio ◽  
Geometrical Parameters ◽  
Phase Flow ◽  
Elastic Instability ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Vibration Responses

In the present study, a series of experiments have been performed to investigate a fluid-elastic instability of a nuclear steam generator U-tube bundle in an air-water two-phase flow condition. A total of 39 U-tubes are arranged in a rotated square array with a pitch-to-diameter ratio of 1.633. The diameter and other geometrical parameters of U-bend region are the same to those of an actual steam generator, but the vertical length of U-tubes are reduced to 2-span in contrast to 9-span of an actual steam generator. The following parameters were experimentally measured to evaluate a fluid-elastic instability of U-tube bundles in a two-phase flow: a general tube vibration response, a critical gap velocity, a damping ratio and a hydrodynamic mass. Based on the experimental measurements, the instability factor, K, of Connors’ relation was preliminary assessed with some assumptions on the velocity and density profiles of the two-phase flow.

Pressure Coefficient Distribution Over Tube Surfaces of Tube Bundle Subjected in Two-Phase Flow

2011 ◽  
Author(s):  
W. G. Sim
Keyword(s):  
Heat Exchangers ◽  
Two Phase Flow ◽  
Pressure Coefficient ◽  
Nuclear Industry ◽  
Fretting Wear ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Coefficient Distribution ◽  
Vibration Excitation

Two-phase cross flow exists in many shell- and tube heat exchangers such as condensers, evaporators and nuclear steam generators. During the last two decades, research devoted to two-phase flow induced vibrations has increased, mainly driven by the nuclear industry. Flow-induced vibration excitation forces can cause excessive vibration which will result in long-term fretting-wear or fatigue. To avoid potential tube failures in heat exchangers, it is required for designer to have guidelines that incorporate flow-induced vibration excitation forces. The phenomenon of the vibration of tubes in two-phase flow is very complex and depends on factors which are nonexistent in single-phase flows. To understand the fluid dynamic forces acting on a structure subjected to two-phase flow, it is essential to get detailed information about the characteristics of two-phase flow. Pressure distributions generated by two-phase flow over tube surfaces yield more general information than the local velocity distribution. The pressure coefficient distribution obtained by experimental test has been evaluated.

Sign in / Sign up

Export Citation Format

Share Document