Pressure Coefficient Distribution Over Tube Surfaces of Tube Bundle Subjected in Two-Phase Flow

2011 ◽  
Author(s):  
W. G. Sim
Keyword(s):  
Heat Exchangers ◽  
Two Phase Flow ◽  
Pressure Coefficient ◽  
Nuclear Industry ◽  
Fretting Wear ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Coefficient Distribution ◽  
Vibration Excitation

Two-phase cross flow exists in many shell- and tube heat exchangers such as condensers, evaporators and nuclear steam generators. During the last two decades, research devoted to two-phase flow induced vibrations has increased, mainly driven by the nuclear industry. Flow-induced vibration excitation forces can cause excessive vibration which will result in long-term fretting-wear or fatigue. To avoid potential tube failures in heat exchangers, it is required for designer to have guidelines that incorporate flow-induced vibration excitation forces. The phenomenon of the vibration of tubes in two-phase flow is very complex and depends on factors which are nonexistent in single-phase flows. To understand the fluid dynamic forces acting on a structure subjected to two-phase flow, it is essential to get detailed information about the characteristics of two-phase flow. Pressure distributions generated by two-phase flow over tube surfaces yield more general information than the local velocity distribution. The pressure coefficient distribution obtained by experimental test has been evaluated.

Vibration Excitation Forces in a Rotated Triangular Tube Bundle Subjected to Two-Phase Cross Flow

2010 ◽  
Author(s):  
H. Senez ◽  
N. W. Mureithi ◽  
M. J. Pettigrew
Keyword(s):  
Steam Generator ◽  
Tube Bundle ◽  
Cross Flow ◽  
Fretting Wear ◽  
Experimental Program ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Fluid Forces ◽  
Vibration Excitation

Two-phase cross flow exists in many shell-and-tube heat exchangers. Flow-induced vibration excitation forces can cause tube motion that will result in long-term fretting wear or fatigue. Detailed flow and vibration excitation force measurements in tube bundles subjected to two-phase cross flow are required to understand the underlying vibration excitation mechanisms. Studies on this subject have already been done, providing results on flow regimes, fluidelastic instabilities, and turbulence-induced vibration. The spectrum of turbulence-induced forces has usually been expected to be similar to that in single-phase flow. However, a recent study, using tubes with a diameter larger than that in a real steam generator, showed the existence of significant quasi-periodic forces in two-phase flow. An experimental program was undertaken with a rotated-triangular array of cylinders subjected to air-water cross-flow, to simulate two-phase mixtures. The tube bundle here has the same geometry as that of a real steam generator. The quasi-periodic forces have now also been observed in this tube bundle. The present work aims to understand turbulence-induced forces acting on the tube bundle, providing results on drag and lift force spectra and their behaviour according to flow parameters, and describing their correlations. Detailed experimental test results are presented in this paper. Comparison is also made with previous measurements with larger diameter tubes. The present results suggest that quasi-periodic fluid forces are not uncommon in tube arrays subjected to two-phase cross-flow.

Two-Phase Flow-Induced Vibration: An Overview (Survey Paper)

1994 ◽  
Vol 116 (3) ◽  
pp. 233-253 ◽  
Author(s):  
M. J. Pettigrew ◽  
C. E. Taylor
Keyword(s):  
Two Phase Flow ◽  
Cross Flow ◽  
Axial Flow ◽  
Random Excitation ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Vibration Excitation ◽  
Fluidelastic Instability ◽  
Excitation Mechanisms

Two-phase flow exists in many industrial components. To avoid costly vibration problems, sound technology in the area of two-phase flow-induced vibration is required. This paper is an overview of the principal mechanisms governing vibration in two-phase flow. Dynamic parameters such as hydrodynamic mass and damping are discussed. Vibration excitation mechanisms in axial flow are outlined. These include fluidelastic instability, phase-change noise, and random excitation. Vibration excitation mechanisms in cross-flow, such as fluidelastic instability, periodic wake shedding, and random excitation, are reviewed.

Thermalhydraulic Analysis of Steam Generators: Application of the Thirst Code to Vibration Analyses

2003 ◽  
Author(s):  
M. Yetisir ◽  
J. Pietralik ◽  
M. Mirzai
Keyword(s):  
Flow Velocity ◽  
Two Phase Flow ◽  
Flow Distribution ◽  
Fretting Wear ◽  
Phase Flow ◽  
Steam Quality ◽  
Steam Generators ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Gap Flow

Flow-induced vibration concerns may be avoided by analysis, which requires the knowledge of flow patterns and the flow distribution in steam generators (SG). Typically, the distributions of flow velocity, fluid density, and, in the case of two-phase flow, distributions of steam quality and two-phase flow regime are needed. Generating this data is not straightforward because of the 3-dimensional nature of flow, complex steam generator geometry, and uncertainties associated with two-phase flow modelling. In this paper, the main features of THIRST, a thermalhydraulic code for recirculating SGs, are described. In addition, the effects of thermalhydraulic modelling and design features on velocity distributions and gap flow velocity needed for flow-induced vibration and fretting-wear calculations are discussed. These include an anisotropic resistance model in the U-bend region, design modifications in the U-bend region to reduce tube vibration, and the prediction of two-phase flow regimes.

Time Domain Simulation of the Vibration of a Steam Generator Tube Subjected to Fluidelastic Forces Induced by Two-Phase Cross-Flow

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Téguewindé Sawadogo ◽  
Njuki Mureithi
Keyword(s):  
Steam Generator ◽  
Two Phase Flow ◽  
Work Rate ◽  
Fretting Wear ◽  
Phase Flow ◽  
Reference Case ◽  
Two Phase ◽  
Steam Generator Tube ◽  
Wide Range ◽  
Instability Regime

Having previously verified the quasi-steady model under two-phase flow laboratory conditions, the present work investigates the feasibility of practical application of the model to a prototypical steam generator (SG) tube subjected to a nonuniform two-phase flow. The SG tube vibration response and normal work-rate induced by tube-support interaction are computed for a range of flow conditions. Similar computations are performed using the Connors model as a reference case. In the quasi-steady model, the fluid forces are expressed in terms of the quasi-static drag and lift force coefficients and their derivatives. These forces have been measured in two-phase flow over a wide range of void fractions making it possible to model the effect of void fraction variation along the tube span. A full steam generator tube subjected to a nonuniform two-phase flow was considered in the simulations. The nonuniform flow distribution corresponds to that along a prototypical steam-generator tube based on thermal-hydraulic computations. Computation results show significant and important differences between the Connors model and the two-phase flow based quasi-steady model. While both models predict the occurrence of fluidelastic instability, the predicted pre-instability and post instability behavior is very different in the two models. The Connors model underestimates the flow-induced negative damping in the pre-instability regime and vastly overestimates it in the post instability velocity range. As a result the Connors model is found to underestimate the work-rate used in the fretting wear assessment at normal operating velocities, rendering the model potentially nonconservative under these practically important conditions. Above the critical velocity, this model largely overestimates the work-rate. The quasi-steady model on the other hand predicts a more moderately increasing work-rate with the flow velocity. The work-rates predicted by the model are found to be within the range of experimental results, giving further confidence to the predictive ability of the model. Finally, the two-phase flow based quasi-steady model shows that fluidelastic forces may reduce the effective tube damping in the pre-instability regime, leading to higher than expected work-rates at prototypical operating velocities.

New Experimental Data and Analysis for Two-Phase Flow-Induced Vibration of Tube Bundles: Preliminary Results

2003 ◽  
Author(s):  
Deepanjan Mitra ◽  
Vijay K. Dhir ◽  
Ivan Catton
Keyword(s):  
Two Phase Flow ◽  
Structural Parameters ◽  
Cross Flow ◽  
Instability Criterion ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Void Fractions ◽  
Comparison Of The Results ◽  
Square Array

In the past, fluid-elastic instability in two-phase flow has been largely investigated with air-water flow. In this work, new experiments are conducted in air-water cross-flow with a fully flexible 5 × 3 normal square array having pitch-to-diameter ratio of 1.4. The tubes have a diameter of 0.016 m and a length of 0.21 m. The vibrations are measured using strain gages installed on piano wires used to suspend the tubes. Experiments are carried out for void fractions from 0%–30%. A comparison of the results of the current tests with previous experiments conducted in air-water cross-flow shows that instability occurs earlier in a fully flexible array as compared to a flexible tube surrounded by rigid tubes in an array. An attempt is made to separate out the effects of structural parameters of three different experimental datasets by replotting the instability criterion by incorporating the instability constant K, in the reduced velocity parameter.

New void fraction equations for two-phase flow in helical heat exchangers using artificial neural networks

2018 ◽  
Vol 130 ◽  
pp. 149-160 ◽  
Author(s):  
A. Parrales ◽  
D. Colorado ◽  
J.A. Díaz-Gómez ◽  
A. Huicochea ◽  
A. Álvarez ◽  
...  
Keyword(s):  
Neural Networks ◽  
Artificial Neural Networks ◽  
Void Fraction ◽  
Heat Exchangers ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Artificial Neural

Analysis of Flow-Induced Vibration Due to Stratified Wavy Two-Phase Flow

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Shuichiro Miwa ◽  
Takashi Hibiki ◽  
Michitsugu Mori
Keyword(s):  
Two Phase Flow ◽  
Dynamic Properties ◽  
Fluid Model ◽  
Dominant Frequency ◽  
Phase Flow ◽  
Flow Induced Vibration ◽  
Two Phase ◽  
Pipe Bend ◽  
Experimental Database ◽  
Force Fluctuation

Fluctuating force induced by horizontal gas–liquid two-phase flow on 90 deg pipe bend at atmospheric pressure condition is considered. Analysis was conducted to develop a model which is capable of predicting the peak force fluctuation frequency and magnitudes, particularly at the stratified wavy two-phase flow regime. The proposed model was developed from the local instantaneous two-fluid model, and adopting guided acoustic theory and dynamic properties of one-dimensional (1D) waves to consider the collisional force due to the interaction between dynamic waves and structure. Comparing the developed model with experimental database, it was found that the main contribution of the force fluctuation due to stratified wavy flow is from the momentum and pressure fluctuations, and collisional effects. The collisional effect is due to the fluid–solid interaction of dynamic wave, which is named as the wave collision force. Newly developed model is capable of predicting the force fluctuations and dominant frequency range with satisfactory accuracy for the flow induced vibration (FIV) caused by stratified wavy two-phase flow in 52.5 mm inner diameter (ID) pipe bend.

Sign in / Sign up

Export Citation Format

Share Document