Influence of kneading time on network formation and electrical properties of wet jet milling treated and untreated SWCNT reinforced polyamide 6 nanocomposites by impedance spectroscopy

Polymer ◽  
2015 ◽  
Vol 80 ◽  
pp. 18-26 ◽  
Author(s):  
Xinlei Yan ◽  
Yusuke Imai ◽  
Daisuke Shimamoto ◽  
Yuji Hotta
2021 ◽  
Vol 363 ◽  
pp. 115593
Author(s):  
V. Kavaliukė ◽  
T. Šalkus ◽  
S. Balčiūnas ◽  
J. Banys ◽  
A.I. Pogodin ◽  
...  

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Pei-Ju Chao ◽  
Eng-Yen Huang ◽  
Kuo-Sheng Cheng ◽  
Yu-Jie Huang

Electrical impedance is one of the most frequently used parameters for characterizing material properties. The resistive and capacitive characteristics of tissue may be revealed by electrical impedance spectroscopy (EIS) as electrical biopsy. This technique could be used to monitor the sequelae after irradiation. In this study, rat intestinal tissues after irradiation were assessed by EIS system based on commercially available integrated circuits. The EIS results were fitted to a resistor-capacitor circuit model to determine the electrical properties of the tissue. The variations in the electrical characteristics of the tissue were compared to radiation injury score (RIS) by morphological and histological findings. The electrical properties, based on receiver operation curve (ROC) analysis, strongly reflected the histological changes with excellent diagnosis performance. The results of this study suggest that electrical biopsy reflects histological changes after irradiation. This approach may significantly augment the evaluation of tissue after irradiation. It could provide rapid results for decision making in monitoring radiation sequelae prospectively.


Author(s):  
Nurul Huda Osman ◽  
Nurul Najiha Mazu ◽  
Josephine Liew Ying Chyi ◽  
Muhammad Mahyiddin Ramli ◽  
Mohammad Abdull Halim Mohd Abdull Majid ◽  
...  

This paper reports on chitosan/bentonite crosslinked (ChB-ECH) film for removal of Cu (II). The effects of chitosan/bentonite ratio on the removal percentage were studied along with the effect of different Cu (II) concentration and the contact time on the film adsorption capacity, qt. The electrical properties of the film are studied, before and after the adsorption occurred, by using impedance spectroscopy for different parameters such as DC conductivity, the complex dielectric constants (ε’ and ε”) and complex electrical modulas (M’ and M’’). The results showed that the chitosan/bentonite ratio of 3:1 produces highest removal percentage at 29 %, while the contact time of 120 minutes was found to be optimum. An increment in the DC conductivity of the ChB-ECH film’s was observed up to 10-7 S/cm as the removal percentage of film increased. The film with the highest Cu (II) adsorb also showed the highest value for ε’ and ε” while exhibiting non-Derby behavior. Shifting of peak amplitude of the M” towards the higher frequency was also observed as the Cu (II) adsorption in the film increased. The results showed that all the electrical parameters can be utilized to determine the amount of adsorbed copper (II) in chitosan/bentonite film.


2017 ◽  
Vol 5 (8) ◽  
pp. 1407-1414 ◽  
Author(s):  
Jacqueline E. Cloud ◽  
Curtis J. Guild ◽  
Sourav Biswas ◽  
Steven L. Suib

Author(s):  
Fernando Seoane ◽  
Ramón Bragos ◽  
Kaj Lindecrantz ◽  
Pere Riu

The passive electrical properties of biological tissue have been studied since the 1920s, and with time, the use of Electrical Bioimpedance (EBI) in medicine has successfully spread (Schwan, 1999). Since the electrical properties of tissue are frequency-dependent (Schwan, 1957), observations of the bioimpedance spectrum have created the discipline of Electrical Impedance Spectroscopy (EIS), a discipline that has experienced a development closely related to the progress of electronic instrumentation and the dissemination of EBI technology through medicine.


Nanomaterials ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 1156 ◽  
Author(s):  
Nayda P. Arias ◽  
María E. Becerra ◽  
Oscar Giraldo

The focus of this paper is centered on the thermal reduction of KMnO4 at controlled temperatures of 400 and 800 °C. The materials under study were characterized by atomic absorption spectroscopy, thermogravimetric analysis, average oxidation state of manganese, nitrogen adsorption–desorption, and impedance spectroscopy. The structural formulas, found as a result of these analyses, were K 0.29 + ( M n 0.84 4 + M n 0.16 3 + ) O 2.07 · 0.61 H 2 O and K 0.48 + ( M n 0.64 4 + M n 0.36 3 + ) O 2.06 · 0.50 H 2 O . The N2 adsorption–desorption isotherms show the microporous and mesoporous nature of the structure. Structural analysis showed that synthesis temperature affects the crystal size and symmetry, varying their electrical properties. Impedance spectroscopy (IS) was used to measure the electrical properties of these materials. The measurements attained, as a result of IS, show that these materials have both electronic and ionic conductivity. The conductivity values obtained at 10 Hz were 4.1250 × 10−6 and 1.6870 × 10−4 Ω−1cm−1 for Mn4 at 298 and 423 K respectively. For Mn8, the conductivity values at this frequency were 3.7074 × 10−7 (298) and 3.9866 × 10−5 Ω−1cm−1 (423 K). The electrical behavior was associated with electron hopping at high frequencies, and protonic conduction and ionic movement of the K+ species, in the interlayer region at low frequencies.


RSC Advances ◽  
2020 ◽  
Vol 10 (47) ◽  
pp. 28007-28018
Author(s):  
Amine Bendahhou ◽  
Karim Chourti ◽  
Rachid El Bouayadi ◽  
Soufian El Barkany ◽  
Mohamed Abou-Salama

In this work, Zn co-doped tungsten bronze having nominal formula Ba5CaTi1.94Zn0.06Nb8O30 has been synthesized and systematically studied for structure, dielectric and electrical properties.


Sign in / Sign up

Export Citation Format

Share Document