Electromagnetic Transduction for Wireless Passive Sensors

This paper presents a technique, based on the matrix pencil method (MPM), for the compression of underwater acoustic signals produced by boat engines. The compressed signal, represented by its complex resonance expansion, is intended to be sent over a low-bit-rate wireless communication channel. We demonstrate that the method can provide data compression greater than 60%, ensuring a correlation greater than 93% between the reconstructed and the original signal, at a sampling frequency of 2.2 kHz. Once the signal was reconstituted, a localization process was carried out with the time reversal method (TR) using information from four different sensors in a simulation environment. This process sought to achieve the identification of the position of the ship using only passive sensors, considering two different sensor arrangements.

Download Full-text

A Closed-Form Estimator for Bearings-Only Fusion of Heterogeneous Passive Sensors

IEEE Transactions on Signal Processing ◽

10.1109/tsp.2020.3035289 ◽

2020 ◽

Vol 68 ◽

pp. 6681-6695

Author(s):

Sanjeev Arulampalam ◽

Laleh Badriasl ◽

Branko Ristic

Keyword(s):

Closed Form ◽

Passive Sensors

Download Full-text

Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽

10.3390/mi12070803 ◽

2021 ◽

Vol 12 (7) ◽

pp. 803

Author(s):

Zhongjie Li ◽

Chuanfu Xin ◽

Yan Peng ◽

Min Wang ◽

Jun Luo ◽

...

Keyword(s):

Power Density ◽

Output Power ◽

Energy Harvester ◽

Hybrid Energy ◽

Energy Harvesters ◽

Piezoelectric Patch ◽

Piezoelectric Energy ◽

Electromagnetic Transduction ◽

Self Powered ◽

Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

Download Full-text

Novel Multilayer SAW Temperature Sensor for Ultra-High Temperature Environments

Micromachines ◽

10.3390/mi12060643 ◽

2021 ◽

Vol 12 (6) ◽

pp. 643

Author(s):

Xuhang Zhou ◽

Qiulin Tan ◽

Xiaorui Liang ◽

Baimao Lin ◽

Tao Guo ◽

...

Keyword(s):

High Temperature ◽

Temperature Sensor ◽

X Ray Diffraction ◽

Aero Engine ◽

Before And After ◽

Application Potential ◽

Passive Sensors ◽

Temperature Exposure ◽

Engine Systems

Performing high-temperature measurements on the rotating parts of aero-engine systems requires wireless passive sensors. Surface acoustic wave (SAW) sensors can measure high temperatures wirelessly, making them ideal for extreme situations where wired sensors are not applicable. This study reports a new SAW temperature sensor based on a langasite (LGS) substrate that can perform measurements in environments with temperatures as high as 1300 °C. The Pt electrode and LGS substrate were protected by an AlN passivation layer deposited via a pulsed laser, thereby improving the crystallization quality of the Pt film, with the function and stability of the SAW device guaranteed at 1100 °C. The linear relationship between the resonant frequency and temperature is verified by various high-temperature radio-frequency (RF) tests. Changes in sample microstructure before and after high-temperature exposure are analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The analysis confirms that the proposed AlN/Pt/Cr thin-film electrode has great application potential in high-temperature SAW sensors.

Download Full-text