scholarly journals Mechanical and physical characterisation of steel fibre reinforced self-compacting concrete: Different aspect ratios and volume fractions of fibres

2022 ◽  
pp. 100335
Author(s):  
Anas Alrawashdeh ◽  
Ozgur Eren
Keyword(s):  
Steel Fibre ◽  
Self Compacting Concrete ◽  
Volume Fractions ◽  
Aspect Ratios

Preliminary Investigation on the Flexural Behaviour of Steel Fibre Reinforced Self-Compacting Concrete Ribbed Slab

2018 ◽  
Vol 15 (1) ◽  
pp. 31
Author(s):  
Nur Aiman Suparlan ◽  
Muhammad Azrul Ku Ayob ◽  
Hazrina Ahmad ◽  
Siti Hawa Hamzah ◽  
Mohd Hisbany Mohd Hashim
Keyword(s):  
Ultimate Load ◽  
Steel Fibre ◽  
Preliminary Investigation ◽  
Bending Test ◽  
Flexural Behaviour ◽  
Self Compacting Concrete ◽  
Two Samples ◽  
Simple Support ◽  
Set Up ◽  
Ultimate Load Carrying Capacity

A ribbed slab structure has the advantage in the reduction of concrete volume in between the ribs resulting in a lower structural self-weight. In order to overcome the drawbacks in the construction process, the application of steel fibre self-compacting concrete (SCFRC) is seen as an alternative material to be used in the slab. This preliminary investigation was carried out to investigate the flexural behaviour of steel fibre self-compacting concrete (SCFRC) as the main material in ribbed slab omitting the conventional reinforcements. Two samples of ribbed slab were prepared for this preliminary study; 2-ribbed and 3-ribbed in 1 m width to identify the effect of the geometry to the slab’s flexural behaviour. The dimension of both samples is 2.5 m x 1 m with 150 mm thickness. The compressive strength of the mix is 48.6 MPa based on the cubes tested at 28 days. Load was applied to failure by using the four point bending test set-up with simple support condition. The result of the experiment recorded ultimate load carrying capacity at 30.68 kN for the 2-ribbed slab and 25.52 kN for 3-ribbed slab. From the results, the ultimate load of the 2-ribbed sample exceeds 3-ribbed by approximately 20%. This proved that even with lower concrete volume, the sample can still withstand an almost similar ultimate load. Cracks was also observed and recorded with the maximum crack width of 2 mm. It can be concluded that the steel fibres do have the potential to withstand flexural loadings. Steel fibre reduces macro-crack forming into micro-cracks and improves concrete ductility, as well as improvement in deflection. This shows that steel fibre reinforced self-compacting concrete is practical as it offers good concrete properties as well as it can be mixed, placed easier without compaction. 

scholarly journals Frost durability of steel fiber self-compacting concrete for pavements

2016 ◽  
Vol 11 (1) ◽  
pp. 35-42 ◽  
Author(s):  
Jerzy Wawrzeńczyk ◽  
Agnieszka Molendowska ◽  
Adam Kłak
Keyword(s):  
Steel Fibre ◽  
Air Entrainment ◽  
Hardened Concrete ◽  
Polymer Microspheres ◽  
Self Compacting Concrete ◽  
Freeze Thaw ◽  
Concrete Mix ◽  
Finished Surface ◽  
Frost Durability ◽  
Scaling Resistance

The paper presents the results from the research on self-compacting concrete with different steel fibre type addition. The reference self-compacting concrete mix with water/binder = 0.33 was prepared, then modified with steel fibres in the amounts of 0–60 kg/m3 and air entrained with polymer microspheres (40 μm diameter). The major objective of the research was to determine the effect of steel fibre and air content on the self-compacting concrete mix properties and hardened concrete frost durability. The tests also included internal cracking and scaling resistance evaluation for concrete specimens subjected to cyclic freeze-thaw process − two beams were frozen in air and two beams were partially submerged in water and then frozen. The scaling resistance was tested using the slab method on the specimens with sawn surface and on the specimens with natural finished surface. Non-air entrained steel fibrereinforced concretes, despite their high strength class (C55/67–C60/75) and medium absorption (4.34–5.11%), showed unsatisfactory resistance to internal cracking and scaling tests. The beams partially submerged in water failed after 100 freeze-thaw cycles, which confirms a significant influence of water uptake from moist environment during freeze-thaw cycles and the acceleration of the damage process. Test results indicate that air entrainment with polymer microspheres is a very effective method and allows obtaining very good air pore structure parameters and frost resistance results. The specimens with top − finished surface exhibited less damage in the scaling resistance tests in relation to the specimens with sawn surface.

scholarly journals Steel fibre spacing in self-compacting concrete precast walls by X-ray computed tomography

2014 ◽  
Vol 48 (12) ◽  
pp. 3863-3874 ◽  
Author(s):  
Tomasz Ponikiewski ◽  
Jacek Katzer ◽  
Monika Bugdol ◽  
Marcin Rudzki
Keyword(s):  
Computed Tomography ◽  
Steel Fibre ◽  
Self Compacting Concrete ◽  
X Ray ◽  
X Ray Computed ◽  
Precast Walls

EXPERIMENTAL RESULTS ON THE SHEAR BEHAVIOUR OF STEEL FIBRE SELF-COMPACTING CONCRETE (SFSCC) BEAMS

2016 ◽  
Vol 78 (11) ◽  
Author(s):  
Juli Asni Lamide ◽  
Roslli Noor Mohamed ◽  
Ahmad Baharuddin Abd Rahman
Keyword(s):  
Mechanical Properties ◽  
Steel Fibre ◽  
Mechanical Performance ◽  
Load Capacity ◽  
Shear Behaviour ◽  
Self Compacting Concrete ◽  
Steel Fibres ◽  
Concrete Mixtures ◽  
Shear Performance ◽  
Better Than

This paper presents an experimental test program that was carried out to investigate the shear performance of steel fibre self-compacting concrete (SFSCC) beams. In this paper, the mechanical performance of results from all mixtures used to cast normal concrete (NC), self-compacting concrete (SCC) and steel fibre self-compacting concrete (SFSCC) were also investigated. In total, 27 cubes, 9 cylinders, 9 prisms and 9 beams were prepared for the assessment of mechanical properties of three different mixtures. Four beams (125 mm x 250 mm x 2200 mm) were tested and cast using three different concrete mixtures, having two different spacing of stirrups as a result of 50% reduction of the stirrups amount. Three beams with different mixtures having similar stirrups spacing 125mm while the fourth beam with SFSCC mixes having 250mm stirrups spacing. The results show that the mechanical properties were positively affected with steel fibres inclusion. The addition of steel fibres showed an increment up to 40% in the shear load capacity for B-SFSCC125 compared to B-NC125 and B-SCC125.  In addition, the crack pattern of B-SFSCC was found better than B-NC and B-SCC.   

Sign in / Sign up

Export Citation Format

Share Document