Current–voltage characteristics of PLD grown manganite based ZnO/La0.5Pr0.2Sr0.3MnO3/SrNb0.002Ti0.998O3 thin film heterostructure

2012 ◽  
Vol 152 (1) ◽  
pp. 34-37 ◽  
Author(s):  
Uma Khachar ◽  
P.S. Solanki ◽  
R.J. Choudhary ◽  
D.M. Phase ◽  
V. Ganesan ◽  
...  
Keyword(s):  
Thin Film ◽  
Current Voltage ◽  
Current Voltage Characteristics

Photoconductivity of Nanocomposite MEH-PPV: TiO2 Thin Films

2011 ◽  
Vol 13 ◽  
pp. 87-92 ◽  
Author(s):  
M.S.P Sarah ◽  
F.S. Zahid ◽  
M.Z. Musa ◽  
U.M. Noor ◽  
Z. Shaameri ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Surface Morphology ◽  
Spin Coating ◽  
Glass Substrate ◽  
Spin Coating Technique ◽  
Coating Technique ◽  
Current Voltage ◽  
Current Voltage Characteristics

The photoconductivity of a nanocomposite MEH-PPV:TiO2 thin film is investigated. The nanocomposite MEH-PPV:TiO2 thin film was deposited on a glass substrate by spin coating technique. The composition of the TiO2 powder was varied from 5 wt% to 20 wt% (with 5 wt% interval). The concentration of the MEH-PPV is given by 1 mg/1 ml. The current voltage characteristics were measured in dark and under illumination. The photoconductivity showed increment in value as the composition of the TiO2 is raised in the polymer based solution. The absorption showed augmentation as the amount of TiO2 is increased. The escalation of the current voltage is then supported by the results of surface morphology.

Temperature variation of the current-voltage characteristics of thin-film gas sensors

2006 ◽  
Vol 32 (1) ◽  
pp. 48-50 ◽  
Author(s):  
V. V. Simakov ◽  
O. V. Yakusheva ◽  
A. I. Grebennikov ◽  
V. V. Kisin
Keyword(s):  
Thin Film ◽  
Temperature Variation ◽  
Gas Sensors ◽  
Current Voltage ◽  
Current Voltage Characteristics

Origin of hysteresis in current-voltage characteristics of polycrystalline silicon thin-film transistors

2009 ◽  
Vol 105 (5) ◽  
pp. 054502 ◽  
Author(s):  
Horng-Chih Lin ◽  
Cheng-Hsiung Hung ◽  
Wei-Chen Chen ◽  
Zer-Ming Lin ◽  
Hsing-Hui Hsu ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Film Transistors ◽  
Polycrystalline Silicon ◽  
Silicon Thin Film ◽  
Current Voltage ◽  
Current Voltage Characteristics

scholarly journals THE USE OF LIQUID PROBES BASED ON AN EUTECTIC SOLUTION FOR STUDYING THE CONDUCTING PROPERTIES OF THIN FILMS

2021 ◽  
pp. 338-344
Author(s):  
Никита Вадимович Пермяков
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Contact Area ◽  
Vertical Axis ◽  
Mechanical Deformation ◽  
Optical Control ◽  
Contact Areas ◽  
Current Voltage ◽  
Current Voltage Characteristics ◽  
Indium Gallium

Работа посвящена разработке модульной четрырехзондовой установки с использованием жидкого контакта на основе индий-галлиевого эвтектического раствора (EGaIn), с помощью которого можно создать прижимные жидкие контакты, не вносящие механические деформации в измеряемые структуры. Предлагается использовать данную установку для измерения вольт-амперных характеристик тонкопленочных образцов. Предполагается модульная схема измерений. Каждый зонд управляется четырьмя моторами для позиционирования и выдавливания капли из шприца для формирования нужного размера пятна контакта. Используется оптический контроль для подготовки зондов и измерения диаметра сформированных контактных областей. Подобраны параметры изготовления жидких зондов, а именно скорости выдавливания и перемещения зонда вдоль вертикальной оси для формирования капли конической формы . Управление установкой осуществляется в среде LabView. The work is devoted to development of a modular four-probe setup using a liquid contact based on an indium-gallium eutectic solution (EGaIn), which can be used to create clamping liquid contacts that do not introduce mechanical deformation into the measured structures. It is proposed to use this setup for measuring the current-voltage characteristics of thin-film samples. A modular measurement scheme is assumed. Each probe is driven by four motors to position and expel a drop from the syringe to form the desired contact area size. Optical control is used to prepare the probes and measure the diameter of the formed contact areas. The parameters for the manufacture of liquid probes are selected, namely, the speed of extrusion and movement of the probe along the vertical axis to form a conical droplet. The installation is controlled in the LabView environment.

Sign in / Sign up

Export Citation Format

Share Document