Characterization of SPEEK/Y2O3 proton exchange membrane treated with high magnetic field

2011 ◽  
Vol 29 (6) ◽  
pp. 604-608 ◽  
Author(s):  
Juying TONG ◽  
Qiang GUO ◽  
Xiaolin TAN ◽  
Xia LI ◽  
Dan LI ◽  
...  
Keyword(s):  
Magnetic Field ◽  
High Magnetic Field ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Exchange Membrane

Synthesis and characterization of novel functionalized perarylated polysiloxane for proton exchange membrane fuel cells

MRS Advances ◽  
2019 ◽  
Vol 4 (64) ◽  
pp. 3579-3585
Author(s):  
Guillermo M. González Guerra ◽  
Alejandro Alatorre-Ordaz ◽  
Gerardo González Garcia ◽  
Jesus S. Jaime-Ferrer
Keyword(s):  
Cyclic Voltammetry ◽  
Fuel Cells ◽  
Proton Exchange Membrane ◽  
Area Under The Curve ◽  
Chlorosulfonic Acid ◽  
Proton Exchange ◽  
Synthesis And Characterization ◽  
A Value ◽  
Exchange Membrane

ABSTRACTThis work presents the synthesis and characterization of a pearylated polysiloxane material (PAP) from a polycondensation reaction, followed by functionalization with HClSO3 by an electrophilic substitution reaction. According to the characterization techniques applied, a sulfonated pearylated polysiloxane was also obtained, (SPAP). The purpose of this sulfonated material is to obtain an ionomer able to be applied in hydrogen fuel cells of the proton exchange membrane kind (PEMFC). The reaction to produce the polysiloxane precursor was carried out with the commercial reagents: PhSiCl3, Ph2SiCl2 and Ph3SiCl in anhydrous THF at 75 °C and the SPAP material was obtained by sulfonation of the precursor with chlorosulfonic acid. PAP and SPAP were characterized by 1H, NMR for liquids, 29Si NMR for solids, IR-ATR, SEM, and cyclic voltammetry. The NMR 29Si spectra show that PAP and PAPS contain crosslinking regions due to PhSiCl3, growing chain zones due to Ph2SiCl2 and polymer termination zones due to Ph3SiCl, obtaining a mixture of siloxanes. The analysis by cyclic voltammetry indicates that by integrating the area under the curve of the adsorption peaks of H2, a value of 0.062 mC/cm2 is obtained, a value close to the commercial ionomer of Nafion®.

Preparation and Characterization of Modified PVDF-g-PSSA Membrane

2010 ◽  
Vol 152-153 ◽  
pp. 44-50 ◽  
Author(s):  
Gui Bao Guo ◽  
Er Ding Han ◽  
Sheng Li An
Keyword(s):  
Relative Humidity ◽  
Sodium Silicate ◽  
Room Temperature ◽  
Proton Exchange Membrane ◽  
Vinylidene Fluoride ◽  
Proton Exchange ◽  
Poly Vinylidene Fluoride ◽  
Relative Humidity Range ◽  
Exchange Membrane

A new method based on a solution graft technique was used to prepare poly (vinylidene fluoride) grafted polystyrene sulfonated acid (PVDF-g-PSSA) proton exchange membrane. Polystyrene is grafted into PVDF modified by plain sodium silicate (Na4SiO4). There is a linear relationship between the degree of grafting and the content of Na4SiO4. Fourier transform infrared spectroscopy is used to characterize changes of the membrane's microstructures after grafting and sulfonation. The morphology of the membrane's microstructures after grafting and sulfonation is studied by scanning electrolytic microscope (SEM). The effect of plain sodium silicate (Na4SiO4) concentration and relative humidity on the conductivity of the electrolyte was investigated by the impedance at room temperature. The results show that the styrene has been grafted into PVDF. The conductivity of PVDF-g-PSSA electrolyte doped 10% plain sodium silicate (Na4SiO4) is 0.016 S/cm at room temperature. The conductivity of the electrolyte changes slightly at a relative humidity range of 20%-70%. The weightlessness of PVDF-g-PSSA electrolyte heated to 40°C was less than 2%, which indicated that water capacity was good.

scholarly journals PEMBUATAN DAN KARAKTERISASI MEMBRAN KOMPOSIT KITOSAN-SODIUM ALGINAT TERFOSFORILASI SEBAGAI PROTON EXCHANGE MEMBRANE FUEL CELL (PEMFC)

2016 ◽  
Vol 1 (1) ◽  
pp. 14
Author(s):  
Siti Wafiroh ◽  
Suyanto Suyanto ◽  
Yuliana Yuliana
Keyword(s):  
Fuel Cell ◽  
Sodium Alginate ◽  
Proton Conductivity ◽  
Composite Membrane ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Methanol Permeability ◽  
Water Swelling ◽  
Exchange Membrane

AbstrakDi era globalisasi ini, kebutuhan bahan bakar fosil semakin meningkat dan ketersediannya semakin menipis. Oleh karena itu, dibutuhkan bahan bakar alternatif seperti Proton Exchange Membrane Fuel Cell (PEMFC). Tujuan dari penelitian ini adalah membuat dan mengkarakterisasi membran komposit kitosan-sodium alginat dari rumput laut coklat (Sargassum sp.) terfosforilasi sebagai Proton Exchange Membrane Fuel Cell (PEMFC). PEM dibuat dengan 4 variasi perbandingan konsentrasi antara kitosan dengan sodium alginat 8:0, 8:1, 8:2, dan 8:4 (b/b). Membran komposit kitosan-sodium alginat difosforilasi dengan STPP 2N. Karakterisasi PEM meliputi: uji tarik, swelling air, kapasitas penukar ion, FTIR, SEM, permeabilitas metanol, dan konduktivitas proton. Berdasarkan hasil analisis tersebut, membran yang optimal adalah perbandingan 8:1 (b/b) dengan nilai modulus young sebesar 0,0901 kN/cm2, swelling air sebesar 19,14 %, permeabilitas metanol sebesar 72,7 x 10-7, dan konduktivitas proton sebesar 4,7 x 10-5 S/cm. Membran komposit kitosan-sodium alginat terfosforilasi memiliki kemampuan yang cukup baik untuk bisa diaplikasikan sebagai membran polimer elektrolit dalam PEMFC. Kata kunci: kitosan, sodium alginat, terfosforilasi, PEMFC  AbstractIn this globalization era, the needs of fossil fuel certainly increases, but its providence decreases. Therefore, we need alternative fuels such as Proton Exchange Membrane Fuel Cell (PEMFC). The purpose of this study is preparationand characterization of phosphorylated chitosan-sodium alginate composite membrane from brown seaweed (Sargassum sp.) as Proton Exchange Membrane Fuel Cell (PEMFC). PEM is produced with 4 variations of concentration ratio between chitosan and sodium alginate 8:0, 8:1, 8:2, and 8:4 (w/w). Chitosan-sodium alginate composite membrane phosphorylated with 2 N STPP. The characterization of PEM include: tensile test, water swelling, ion exchange capacity, FTIR, SEM, methanol permeability, and proton conductivity. Based on the analysis result, the optimal membrane is ratio of 8:1 (w/w) with the value of Young’s modulus about 0.0901 kN/cm2, water swelling at 19.14%, methanol permeability about 72.7 x 10-7, and proton conductivity about 4.7 x 10-5 S/cm. The phosphorylated chitosan-sodium alginate composite membrane has good potentials for the application of the polymer electrolyte membrane in PEMFC. Keywords: chitosan, sodium alginate, phosphorylated, PEMFC

Fabrication and Characterization of Carbon Fiber Paper for Application of Proton Exchange Membrane Fuel Cells

2014 ◽  
Vol 787 ◽  
pp. 407-411 ◽  
Author(s):  
Kai Yang ◽  
Zhi Yong Xie ◽  
Qi Zhong Huang ◽  
Xian Tang ◽  
Rong Hu
Keyword(s):  
Fuel Cells ◽  
Carbon Content ◽  
Proton Exchange Membrane ◽  
Chemical Vapor ◽  
Heating Time ◽  
Proton Exchange ◽  
Carbon Paper ◽  
Carbon Fiber Paper ◽  
Exchange Membrane

Using the dry method-prepared polyacrylonitrile based carbon fibers as raw the material, carbon paper applied for proton exchange membrane fuel cells was prepared by the processes of molding, high temperature carbonization, chemical vapor deposition (CVD), and graphitization. The effects of resin carbon content and subsequent heat-treatment process parameters on the properties of carbon paper were studied. The results show that: the resin carbon content is an important factor to affect the density, thickness, through-plane resistivity and porosity of carbon paper. When the resin carbon content is 20%, the thickness of carbon paper is 0.20mm, the density is 0.41g/cm3, and the porosity is 74.5%, in line with requirements of the fuel cell. When the heating time is 4 hours, the porosity is 71.9%.

Preparation and characterization of zeolite polymer composite proton exchange membrane

2015 ◽  
pp. 1-9
Author(s):  
Anis Nurdhiani Rosdi ◽  
Yee Li Kang ◽  
Monash Purushothaman ◽  
Shaliza Ibrahim ◽  
Saravanan Pichiah
Keyword(s):  
Polymer Composite ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Exchange Membrane

The Effect of Injection and Suction on the Interfacial Mass Transport Resistance in a Proton Exchange Membrane Fuel Cell Air Channel

2014 ◽  
Author(s):  
Mustafa Koz ◽  
Satish G. Kandlikar
Keyword(s):  
Proton Exchange Membrane ◽  
Numerical Study ◽  
Gas Diffusion ◽  
Proton Exchange ◽  
Channel Cross Section ◽  
Flow Through ◽  
Air Channel ◽  
Air Channels ◽  
Exchange Membrane

Proton exchange membrane fuel cells are efficient and environmentally friendly electrochemical engines. The present work focuses on air channels that bring the oxidant air into the cell. Characterization of the oxygen concentration drop from the channel to the gas diffusion layer (GDL)-channel interface is a need in the modeling community. This concentration drop is expressed with the non-dimensional Sherwood number (Sh). At the aforementioned interface, the air can have a non-zero velocity normal to the interface: injection of air to the channel and suction of air from the channel. A water droplet in the channel can constrict the channel cross section and lead to a flow through the GDL. In this numerical study, a rectangular air channel, GDL, and a stationary droplet on the GDL-channel interface are simulated to investigate the Sh under droplet induced injection/suction conditions. The simulations are conducted with a commercially available software package, COMSOL Multiphysics.

Sign in / Sign up

Export Citation Format

Share Document