scholarly journals Considerations on the Cost of Electricity Production in the Context of Integration Operating Activities Underground and Production of Coal in Thermal Power Stations Electricity in the Jiu Valley Mining Area

2015 ◽  
Vol 23 ◽  
pp. 371-377 ◽  
Author(s):  
Mangu Sorin ◽  
Iloiu Mirela ◽  
Csiminga Diana
1993 ◽  
Vol 115 (4) ◽  
pp. 452-462 ◽  
Author(s):  
R. J. Nathan ◽  
M. P. Norton

The overall objective of the work reported in this paper is to minimize the cost of power generation in thermal power stations utilizing pulverized coal combustion processes for steam generation. The strategy of achieving this objective is based on an “on-condition maintenance” philosophy and vibration based diagnostic signature analysis techniques. The coal pulverizers reported on here are 783 RP (roll pressure) and 823 RP combustion engineering (CE) bowl-roller coal pulverizers (bowl mills) installed at the State Energy Commission of Western Australia (SECWA) power stations. This paper reviews the design philosophy, operational principles, and system dynamics and establishes the procedures for identifying the potential malfunction of bowl mills and their associated components. The influence of operating parameters, such as coal flow, primary air flow, and operating temperature, on mill vibration are investigated. The effects of journal spring force variation, such as magnitude, uneven spring force, and broken springs, are also studied. Special attention is also given to the diagnosis of the top radial bearing problem due to its remoteness from the bowl mill external structure. A spectral recovery technique utilizing the inverse frequency response function was developed for trend analysis and diagnostic purposes.


2015 ◽  
Vol 725-726 ◽  
pp. 208-213 ◽  
Author(s):  
Yuriy Lazarev ◽  
Marina Chakir ◽  
Elizaveta Sukhareva ◽  
Yulia Ibraeva

This article is about strengthening soil in application of the problem with utilization of ash-and-slag wastes from coil thermal power-stations to reduce the cost of construction of road, to get sufficiently strong of road bases with reinforcing soils, to provide a higher rate of acquisition of durability and higher durability and frost resistance.


2020 ◽  
Vol 67 (11) ◽  
pp. 800-804
Author(s):  
K. E. Aronson ◽  
B. E. Murmansky ◽  
V. B. Novoselov ◽  
Yu. M. Brodov ◽  
A. Yu. Sosnovsky ◽  
...  

Desalination ◽  
1999 ◽  
Vol 126 (1-3) ◽  
pp. 261-266
Author(s):  
A.S. Sedlov ◽  
V.V. Shischenko ◽  
V.F. Ghidkih ◽  
R.M. Chasiachmetov ◽  
Y.I. Pichushkin

2021 ◽  
Vol 323 ◽  
pp. 8-13
Author(s):  
Jadambaa Temuujin ◽  
Damdinsuren Munkhtuvshin ◽  
Claus H. Ruescher

With a geological reserve of over 170 billion tons, coal is the most abundant energy source in Mongolia with six operating thermal power stations. Moreover, in Ulaanbaatar city over 210000 families live in the Ger district and use over 800000 tons of coal as a fuel. The three thermal power plants in Ulaanbaatar burn about 5 million tons of coal, resulting in more than 500000 tons of coal combustion by-products per year. Globally, the ashes produced by thermal power plants, boilers, and single ovens pose serious environmental problems. The utilization of various types of waste is one of the factors determining the sustainability of cities. Therefore, the processing of wastes for re-use or disposal is a critical topic in waste management and materials research. According to research, the Mongolian capital city's air and soil quality has reached a disastrous level. The main reasons for air pollution in Ulaanbaatar are reported as being coal-fired stoves of the Ger residential district, thermal power stations, small and medium-sized low-pressure furnaces, and motor vehicles. Previously, coal ashes have been used to prepare advanced materials such as glass-ceramics with the hardness of 6.35 GPa, geopolymer concrete with compressive strength of over 30 MPa and zeolite A with a Cr (III) removal capacity of 35.8 mg/g. Here we discuss our latest results on the utilization of fly ash for preparation of a cement stabilized base layer for paved roads, mechanically activated fly ash for use in concrete production, and coal ash from the Ger district for preparation of an adsorbent. An addition of 20% fly ash to 5-8% cement made from a mixture of road base gave a compressive strength of ~ 4MPa, which exceeds the standard. Using coal ashes from Ger district prepared a new type of adsorbent material capable of removing various organic pollutants from tannery water was developed. This ash also showed weak leaching characteristics in water and acidic environment, which opens up an excellent opportunity to utilize.


Sign in / Sign up

Export Citation Format

Share Document