scholarly journals Two-dimensional plastic flow of foams and emulsions in a channel: experiments and lattice Boltzmann simulations

2015 ◽  
Vol 766 ◽  
pp. 556-589 ◽  
Author(s):  
B. Dollet ◽  
A. Scagliarini ◽  
M. Sbragaglia

AbstractIn order to understand the flow profiles of complex fluids, a crucial issue concerns the emergence of spatial correlations among plastic rearrangements exhibiting cooperativity flow behaviour at the macroscopic level. In this paper, the rate of plastic events in a Poiseuille flow is experimentally measured on a confined foam in a Hele-Shaw geometry. The correlation with independently measured velocity profiles is quantified by looking at the relationship between the localisation length of the velocity profiles and the localisation length of the spatial distribution of plastic events. To complement the cooperativity mechanisms studied in foam with those of other soft glassy systems, we compare the experiments with simulations of dense emulsions based on the lattice Boltzmann method, which are performed both with and without wall friction. Finally, unprecedented results on the distribution of the orientation of plastic events show that there is a non-trivial correlation with the underlying local shear strain. These features, not previously reported for a confined foam, lend further support to the idea that cooperativity mechanisms, originally invoked for concentrated emulsions (Goyon et al., Nature, vol. 454, 2008, pp. 84–87), have parallels in the behaviour of other soft glassy materials.

2009 ◽  
Vol 283-286 ◽  
pp. 364-369 ◽  
Author(s):  
M.R. Arab ◽  
Bernard Pateyron ◽  
Mohammed El Ganaoui ◽  
Nicolas Calvé

For simulating flows in a porous medium, a numerical tool based on the Lattice Boltzmann Method (LBM) is developed with regards to the classical D2Q9 model. A short description of this model is presented. This technique, applied to two-dimensional configurations, indicates its ability to simulate phenomena of heat and mass transfer. The numerical study is extended to estimate physical parameters that characterize porous materials, like the so-called Effective Thermal Conductivity (ETC) which is of our interest in this paper. Obtained results are compared with those which could be found analytically and by theoretical models. Finally, a porous medium is considered to find its ETC.


2007 ◽  
Vol 129 (3) ◽  
pp. 603-610 ◽  
Author(s):  
Gunther Brenner ◽  
Ahmad Al-Zoubi ◽  
Merim Mukinovic ◽  
Hubert Schwarze ◽  
Stefan Swoboda

The effect of surface texture and roughness on shear and pressure forces in tribological applications in the lubrication regime is analyzed by means of lattice-Boltzmann simulations that take the geometry of real surface elements into account. Topographic data on representative surface structures are obtained with high spatial resolution with the application of an optical interference technique. The three-dimensional velocity field past these surfaces is computed for laminar flow of Newtonian fluids in the continuum regime. Subsequently, pressure and shear flow factors are obtained by evaluating the velocity field in accordance with the extended Reynolds equation of Patir and Cheng (1978, ASME J. Tribol., 100, pp. 12–17). The approach allows an efficient determination of the hydrodynamic characteristics of microstructured surfaces in lubrication. Especially, the influence of anisotropy of surface texture on the hydrodynamic load capacity and friction is determined. The numerical method used in the present work is verified for a simplified model configuration, the flow past a channel with sinusoidal walls. The results obtained indicate that full numerical simulations should be used to accurately and efficiently compute the characteristic properties of film flows past rough surfaces and may therefore contribute to a better understanding and prediction of tribological problems.


2005 ◽  
Vol 16 (01) ◽  
pp. 25-44 ◽  
Author(s):  
KANNAN N. PREMNATH ◽  
JOHN ABRAHAM

In this paper, three-dimensional computations of drop–drop interactions using the lattice Boltzmann method (LBM) are reported. The LBM multiphase flow model employed is evaluated for single drop problems and binary drop interactions. These include the verification of Laplace–Young relation for static drops, drop oscillations, and drop deformation and breakup in simple shear flow. The results are compared with experimental data, analytical solutions and numerical solutions based on other computational methods, as applicable. Satisfactory agreement is shown. Initial studies of drop–drop interactions involving the head-on collisions of drops in quiescent medium and off-center collision of drops in the presence of ambient shear flow are considered. As expected, coalescence outcome is observed for the range of parameters studied.


2011 ◽  
Vol 9 (5) ◽  
pp. 1128-1136 ◽  
Author(s):  
Nikolaos Prasianakis ◽  
Santosh Ansumali

AbstractThe exact solution to the hierarchy of nonlinear lattice Boltzmann kinetic equations, for the stationary planar Couette flow for any Knudsen number was presented by S. Ansumali et al. [Phys. Rev. Lett., 98 (2007), 124502]. In this paper, simulation results at a non-vanishing value of the Knudsen number are compared with the closed-form solutions for the higher-order moments. The order of convergence to the exact solution is also studied. The lattice Boltzmann simulations are in excellent agreement with the exact solution.


1999 ◽  
Vol 385 ◽  
pp. 41-62 ◽  
Author(s):  
DEWEI QI

A lattice-Boltzmann method has been developed to simulate suspensions of both spherical and non-spherical particles in finite-Reynolds-number flows. The results for sedimentation of a single elliptical particle are shown to be in excellent agreement with the results of Huang, Hu & Joseph (1998) who used a finite-element method. Sedimentation of two-dimensional circular and rectangular particles in a two-dimensional channel and three-dimensional spherical particles in a tube with square cross-section is simulated. Computational results are consistent with experimentally observed phenomena, such as drafting, kissing and tumbling.


Author(s):  
Long Sang ◽  
Yiping Hong ◽  
Fujun Wang

Droplet formation in a co-flowing microfluidic device is investigated with the lattice Boltzmann method (LBM). This LBM code was validated with two benchmarks such as Poiseuille flow through a straight duct and Taylor deformation on droplets between two shearing plates. A comparison of experimental droplet formation in a microchannel (Cramer et al, 2004) showed good quantitative agreement with our modeling results. With this code, a large number of simulations were carried out with various inlet flow rate ratios at various Re and various interfacial tensions in the co-flowing microfluidic system. All resulting droplet sizes are discussed quantitatively with the nondimensional parameters, which is helpful for droplet control in different co-flowing devices.


2007 ◽  
Vol 18 (04) ◽  
pp. 455-462 ◽  
Author(s):  
MARTIN GEIER ◽  
ANDREAS GREINER ◽  
JAN G. KORVINK

The theory of the lattice Boltzmann automaton is based on a moment transform which is not Galilean invariant. It is explained how the central moments transform, used in the cascaded lattice Boltzmann method, overcomes this problem by choosing the center of mass coordinate system as the frame of reference. Galilean invariance is restored and the form of the kinetic theory is unaffected. Conservation laws are not compromised by the high order polyinomials in the equilibrium distribution arising from the central moment transform. Two sources of instabilities in lattice Boltzmann simulations are discussed: negative numerical viscosity due to insufficient Galilean invariance and aliasing. The cascaded lattice Boltzmann automaton overcomes both problems. It is discussed why aliasing is unavoidable in lattice Boltzmann methods that rely on a single relaxation time. An appendix lists the complete scattering operator of the D2Q9 cascaded lattice Boltzmann automaton.


2003 ◽  
Vol 17 (01n02) ◽  
pp. 21-26 ◽  
Author(s):  
T. INAMURO ◽  
R. TOMITA ◽  
F. OGINO

A lattice Boltzmann method for multicomponent immiscible fluids is applied to simulations of drop deformation and breakup in shear flows for various capillary numbers and viscosity ratios at three different Revnolds numbers, Re = 0.2, 1, 10. The effect of the Reynolds number on drop deformation and breakup in shear flows is investigated. It is found that the drop is easier to deform and to be ruptured as the Reynolds number increases.


Sign in / Sign up

Export Citation Format

Share Document