scholarly journals Prediction of noise from serrated trailing edges

2016 ◽  
Vol 793 ◽  
pp. 556-588 ◽  
Author(s):  
B. Lyu ◽  
M. Azarpeyvand ◽  
S. Sinayoko
Keyword(s):  
Noise Reduction ◽  
Analytical Model ◽  
Leading Edge ◽  
Experimental Investigations ◽  
Destructive Interference ◽  
Trailing Edge ◽  
Trailing Edges ◽  
Mach Numbers ◽  
Trailing Edge Serrations ◽  
High Mach

A new analytical model is developed for the prediction of noise from serrated trailing edges. The model generalizes Amiet’s trailing-edge noise theory to sawtooth trailing edges, resulting in a complicated partial differential equation. The equation is then solved by means of a Fourier expansion technique combined with an iterative procedure. The solution is validated through comparison with the finite element method for a variety of serrations at different Mach numbers. The results obtained using the new model predict noise reduction of up to 10 dB at 90$^{\circ }$ above the trailing edge, which is more realistic than predictions based on Howe’s model and also more consistent with experimental observations. A thorough analytical and numerical analysis of the physical mechanism is carried out and suggests that the noise reduction due to serration originates primarily from interference effects near the trailing edge. A closer inspection of the proposed mathematical model has led to the development of two criteria for the effectiveness of the trailing-edge serrations, consistent but more general than those proposed by Howe. While experimental investigations often focus on noise reduction at 90$^{\circ }$ above the trailing edge, the new analytical model shows that the destructive interference scattering effects due to the serrations cause significant noise reduction at large polar angles, near the leading edge. It has also been observed that serrations can significantly change the directivity characteristics of the aerofoil at high frequencies and even lead to noise increase at high Mach numbers.

Experimental investigation of NACA-0012 airfoil instability noise with sawtooth trailing edges

2021 ◽  
pp. 0309524X2110605
Author(s):  
Basim Al Tlua ◽  
Joana Rocha
Keyword(s):  
Noise Reduction ◽  
Reynolds Numbers ◽  
Radiation Characteristics ◽  
Trailing Edge ◽  
Trailing Edges ◽  
Noise Measurements ◽  
Parametric Studies ◽  
Trailing Edge Serrations ◽  
Field Noise ◽  
Naca 0012

This study presents an experimental study of the effect of sawtooth trailing-edge serrations on airfoil instability noise. The far-field noise measurements are obtained to investigate the noise radiation characteristics of a NACA-0012 airfoil operated at various angles of attack: 0°, 5°, and 10°, and covered Reynolds numbers of 2.87 × 105, 3.71 × 105, and 5 × 105. It is found that as the Reynolds number increases, the instability noise shifts from tonal to broadband, whereas as the angle of attack increases, it shifts from broadband to tonal. Furthermore, sawtooth trailing-edges are used to minimize instability tonal noise, leading to considerable self-noise reduction. Parametric studies of the serration amplitude 2 h and streamwise wavelength λ are performed to understand the effect of sawtooth trailing-edges on noise reduction. It is observed that the sound pressure reduction level is sensitive to both the amplitude and streamwise wavelength. Overall, the sawtooth trailing-edge with larger amplitude and smaller wavelength produce the greatest amount of noise reduction.

Numerical study on the airfoil self-noise of three owl-based wings with the trailing-edge serrations

2021 ◽  
pp. 095441002098822
Author(s):  
Dian Li ◽  
Xiaomin Liu ◽  
Lei Wang ◽  
Fujia Hu ◽  
Guang Xi
Keyword(s):  
Flow Field ◽  
Noise Reduction ◽  
Numerical Study ◽  
Barn Owl ◽  
Aerodynamic Noise ◽  
Frequency Noise ◽  
Trailing Edge ◽  
Reduction Mechanisms ◽  
Trailing Edge Serrations ◽  
Bionic Airfoil

Previous publications have summarized that three special morphological structures of owl wing could reduce aerodynamic noise under low Reynolds number flows effectively. However, the coupling noise-reduction mechanism of bionic airfoil with trailing-edge serrations is poorly understood. Furthermore, while the bionic airfoil extracted from natural owl wing shows remarkable noise-reduction characteristics, the shape of the owl-based airfoils reconstructed by different researchers has some differences, which leads to diversity in the potential noise-reduction mechanisms. In this article, three kinds of owl-based airfoils with trailing-edge serrations are investigated to reveal the potential noise-reduction mechanisms, and a clean airfoil based on barn owl is utilized as a reference to make a comparison. The instantaneous flow field and sound field around the three-dimensional serrated airfoils are simulated by using incompressible large eddy simulation coupled with the FW-H equation. The results of unsteady flow field show that the flow field of Owl B exhibits stronger and wider-scale turbulent velocity fluctuation than that of other airfoils, which may be the potential reason for the greater noise generation of Owl B. The scale and magnitude of alternating mean convective velocity distribution dominates the noise-reduction effect of trailing-edge serrations. The noise-reduction characteristic of Owl C outperforms that of Barn owl, which suggests that the trailing-edge serrations can suppress vortex shedding noise of flow field effectively. The trailing-edge serrations mainly suppress the low-frequency noise of the airfoil. The trailing-edge serration can suppress turbulent noise by weakening pressure fluctuation.

Experimental study of wavy trailing edge serrations on flat rotor blades

2021 ◽  
Vol 263 (5) ◽  
pp. 1855-1866
Author(s):  
Sai Manikanta Kaja ◽  
K. Sriinivasan ◽  
A. Jaswanth Kalyan Kumar
Keyword(s):  
Experimental Study ◽  
Noise Reduction ◽  
Pitch Angle ◽  
Acoustic Emissions ◽  
Broadband Noise ◽  
Rotor Blades ◽  
Tonal Noise ◽  
Trailing Edge ◽  
Low Speeds ◽  
Trailing Edge Serrations

A detailed experimental study is conducted to observe the effect of various parameters like wavelength, depth of serrations, and pitch angle on serrated blades' acoustic emissions at low speeds up to 2000 rpm. Experiments are conducted on flat blade rotors with sinusoidal serrations on the trailing edge of blades with different amplitudes and wavelengths. A total of 7 blades with different serration configurations, including a base configuration, are studied, five of them have serrations throughout the span of the blade, and one configuration has serration of varying amplitude on the farther half of the blade. It is observed that some blade configurations have resulted in tonal noise reduction noise as much as 8dB, whereas some of the serration configurations reduce very little to none, there is no significant effect of T.E serrations on the broadband noise emitted by the rotor. Directivity of noise generated from the rotor, the effect of serrations on the directivity of the noise is studied.

scholarly journals Role of Polymeric Coating on Metallic Foams to Control the Aeroacoustic Noise Reduction of Airfoils with Permeable Trailing Edges

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1087 ◽  
Author(s):  
Reza Hedayati ◽  
Alejandro Rubio Carpio ◽  
Salil Luesutthiviboon ◽  
Daniele Ragni ◽  
Francesco Avallone ◽  
...  
Keyword(s):  
Noise Reduction ◽  
Metal Foams ◽  
Polymeric Coating ◽  
Metallic Foams ◽  
Noise Mitigation ◽  
Trailing Edge ◽  
Reference Case ◽  
Pore Sizes ◽  
Coated Metal ◽  
Trailing Edges

Studies on porous trailing edges, manufactured with open-cell Ni-Cr-Al foams with sub-millimeter pore sizes, have shown encouraging results for the mitigation of turbulent boundary-layer trailing-edge noise. However, the achieved noise mitigation is typically dependent upon the pore geometry, which is fixed after manufacturing. In this study, a step to control the aeroacoustics effect of such porous trailing edges is taken, by applying a polymeric coating onto the internal foam structure. Using this method, the internal topology of the foam is maintained, but its permeability is significantly affected. This study opens a new possibility of aeroacoustic control, since the polymeric coatings are temperature responsive, and their thickness can be controlled inside the foam. Porous metallic foams with pore sizes of 580, 800, and 1200 μm are (internally) spray-coated with an elastomeric coating. The uncoated and coated foams are characterized in terms of reduced porosity, average coating thickness and air-flow resistance. Subsequently, the coated and uncoated foams are employed to construct tapered inserts installed at the trailing edge of an NACA 0018 airfoil. The noise mitigation performances of the coated metal foams are compared to those of uncoated metal foams with either similar pore size or permeability value, and both are compared to the solid trailing edge reference case. Results show that that the permeability of the foam can be easily altered by the application of an internal coating on the metallic foams. The noise reduction characteristics of the coated foams are similar to equivalent ones with metallic materials, provided that the coating material is rigid enough not to plastically deform under flow conditions.

Boundary Backstepping Control of Flow-Induced Vibrations of a Membrane at High Mach Numbers

2015 ◽  
Vol 137 (8) ◽  
Author(s):  
Aziz Sezgin ◽  
Miroslav Krstic
Keyword(s):  
Wave Equation ◽  
Original System ◽  
Target System ◽  
Spanwise Direction ◽  
Infinite Length ◽  
Flow Induced Vibration ◽  
Trailing Edge ◽  
Flow Induced Vibrations ◽  
Mach Numbers ◽  
High Mach

We design a controller for flow-induced vibrations of an infinite-band membrane, with flow running across the band and only above it, and with actuation only on the trailing edge of the membrane. Due to the infinite length of the membrane, the dynamics of the membrane in the spanwise direction are neglected, namely, we employ a one-dimensional (1D) model that focuses on streamwise vibrations. This framework is inspired by a flow along an airplane wing with actuation on the trailing edge. The model of the flow-induced vibration is given by a wave partial differential equation (PDE) with an antidamping term throughout the 1D domain. Such a model is based on linear aeroelastic theory for Mach numbers above 0.8. To design a controller, we introduce a three-stage backstepping transformation. The first stage gets the system to a critically antidamped wave equation, changing the stiffness coefficient's value but not its sign. The second stage changes the system from a critically antidamped to a critically damped equation with an arbitrary damping coefficient. The third stage adjusts stiffness arbitrarily. The controller and backstepping transformation map the original system into a target system given by a wave equation with arbitrary positive damping and stiffness.

scholarly journals Features of owl wings that promote silent flight

2017 ◽  
Vol 7 (1) ◽  
pp. 20160078 ◽  
Author(s):  
Hermann Wagner ◽  
Matthias Weger ◽  
Michael Klaas ◽  
Wolfgang Schröder
Keyword(s):  
Noise Reduction ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Wing Loading ◽  
Trailing Edge ◽  
Future Directions ◽  
Trailing Edge Noise ◽  
Aerodynamic Properties ◽  
Morphological Adaptations ◽  
Noise Production

Owls are an order of birds of prey that are known for the development of a silent flight. We review here the morphological adaptations of owls leading to silent flight and discuss also aerodynamic properties of owl wings. We start with early observations (until 2005), and then turn to recent advances. The large wings of these birds, resulting in low wing loading and a low aspect ratio, contribute to noise reduction by allowing slow flight. The serrations on the leading edge of the wing and the velvet-like surface have an effect on noise reduction and also lead to an improvement of aerodynamic performance. The fringes at the inner feather vanes reduce noise by gliding into the grooves at the lower wing surface that are formed by barb shafts. The fringed trailing edge of the wing has been shown to reduce trailing edge noise. These adaptations to silent flight have been an inspiration for biologists and engineers for the development of devices with reduced noise production. Today several biomimetic applications such as a serrated pantograph or a fringed ventilator are available. Finally, we discuss unresolved questions and possible future directions.

Sign in / Sign up

Export Citation Format

Share Document