scholarly journals Turbulent channel flow of a dense binary mixture of rigid particles

2017 ◽  
Vol 818 ◽  
pp. 623-645 ◽  
Author(s):  
Iman Lashgari ◽  
Francesco Picano ◽  
Pedro Costa ◽  
Wim-Paul Breugem ◽  
Luca Brandt
Keyword(s):  
Binary Mixture ◽  
Channel Flow ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Turbulent Channel Flow ◽  
Channel Height ◽  
Wall Region ◽  
Small Particles ◽  
Rigid Particles ◽  
Large Particles

We study turbulent channel flow of a binary mixture of finite-sized neutrally buoyant rigid particles by means of interface-resolved direct numerical simulations. We fix the bulk Reynolds number and total solid volume fraction, $Re_{b}=5600$ and $\unicode[STIX]{x1D6F7}=20\,\%$, and vary the relative fraction of small and large particles. The binary mixture consists of particles of two different sizes, $2h/d_{l}=20$ and $2h/d_{s}=30$ where $h$ is the half-channel height and $d_{l}$ and $d_{s}$ the diameters of the large and small particles. While the particulate flow statistics exhibit a significant alteration of the mean velocity profile and turbulent fluctuations with respect to the unladen flow, the differences between the mono-disperse and bi-disperse cases are small. However, we observe a clear segregation of small particles at the wall in binary mixtures, which affects the dynamics of the near-wall region and thus the overall drag. This results in a higher drag in suspensions with a larger number of large particles. As regards bi-disperse effects on the particle dynamics, a non-monotonic variation of the particle dispersion in the spanwise (homogeneous) direction is observed when increasing the percentage of small/large particles. Finally, we note that particles of the same size tend to cluster more at contact whereas the dynamics of the large particles gives the highest collision kernels due to a higher approaching speed.

Large Eddy Simulation of Turbulent Flow Laden With Binary Mixture of Particles

2007 ◽  
Author(s):  
Neng-Tsung Chang ◽  
Chih-Hung Hsu ◽  
Keh-Chin Chang
Keyword(s):  
Binary Mixture ◽  
Large Eddy Simulation ◽  
Channel Flow ◽  
Turbulent Channel Flow ◽  
Wall Region ◽  
Wall Roughness ◽  
Wall Model ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Normal Particle

Particle-laden turbulent channel flow at Reτ = 644, loaded with binary mixture of particles, is numerically studied using the Lagrangian particle tracking method coupled with large eddy simulation. Turbulence statistics of different particle groups are analyzed. Two particle-wall models are applied to this study with / without considering wall roughness. Taking into considerations of rough wall model, the effect of wall roughness in the computations strengthens the wall-normal particle velocity fluctuations. As a result, particles tend to move from the near-wall region to the central core region. It leads to decrement of particle accumulation in the near-wall region as compared to the case considering the smooth wall model. The wall-normal particle mixing capability is enhanced which results in the redistribution of particles in the channel. The behavior of particle motion in the turbulent channel flow should be, thus, dependent on not only the value of Stokes number but also the wall roughness level.

Topology of fine-scale motions in turbulent channel flow

1996 ◽  
Vol 310 ◽  
pp. 269-292 ◽  
Author(s):  
Hugh M. Blackburn ◽  
Nagi N. Mansour ◽  
Brian J. Cantwell
Keyword(s):  
Strain Rate ◽  
Channel Flow ◽  
Velocity Gradient ◽  
Outer Region ◽  
Turbulent Channel Flow ◽  
Principal Strain ◽  
Wall Region ◽  
Fine Scale ◽  
Stable Focus ◽  
Topological Features

An investigation of topological features of the velocity gradient field of turbulent channel flow has been carried out using results from a direct numerical simulation for which the Reynolds number based on the channel half-width and the centreline velocity was 7860. Plots of the joint probability density functions of the invariants of the rate of strain and velocity gradient tensors indicated that away from the wall region, the fine-scale motions in the flow have many characteristics in common with a variety of other turbulent and transitional flows: the intermediate principal strain rate tended to be positive at sites of high viscous dissipation of kinetic energy, while the invariants of the velocity gradient tensor showed that a preference existed for stable focus/stretching and unstable node/saddle/saddle topologies. Visualization of regions in the flow with stable focus/stretching topologies revealed arrays of discrete downstream-leaning flow structures which originated near the wall and penetrated into the outer region of the flow. In all regions of the flow, there was a strong preference for the vorticity to be aligned with the intermediate principal strain rate direction, with the effect increasing near the walls in response to boundary conditions.

scholarly journals Large eddy simulation of turbulent channel flow using differential equation wall model

2018 ◽  
Vol 15 (2) ◽  
pp. 75-89
Author(s):  
Muhammad Saiful Islam Mallik ◽  
Md. Ashraf Uddin
Keyword(s):  
Differential Equation ◽  
Flow Field ◽  
Channel Flow ◽  
Turbulent Channel Flow ◽  
Wall Region ◽  
Computational Domain ◽  
Wall Model ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Near Wall

A large eddy simulation (LES) of a plane turbulent channel flow is performed at a Reynolds number Re? = 590 based on the channel half width, ? and wall shear velocity, u? by approximating the near wall region using differential equation wall model (DEWM). The simulation is performed in a computational domain of 2?? x 2? x ??. The computational domain is discretized by staggered grid system with 32 x 30 x 32 grid points. In this domain the governing equations of LES are discretized spatially by second order finite difference formulation, and for temporal discretization the third order low-storage Runge-Kutta method is used. Essential turbulence statistics of the computed flow field based on this LES approach are calculated and compared with the available Direct Numerical Simulation (DNS) and LES data where no wall model was used. Comparing the results throughout the calculation domain we have found that the LES results based on DEWM show closer agreement with the DNS data, especially at the near wall region. That is, the LES approach based on DEWM can capture the effects of near wall structures more accurately. Flow structures in the computed flow field in the 3D turbulent channel have also been discussed and compared with LES data using no wall model.

Predictability Study of Viscoelastic Turbulent Channel Flow Using Deep Learning

2019 ◽  
Author(s):  
Atsushi Nagamachi ◽  
Takahiro Tsukahara
Keyword(s):  
Channel Flow ◽  
Viscoelastic Fluid ◽  
Coherent Structures ◽  
Turbulent Channel Flow ◽  
Wall Region ◽  
Nonlinear Relationship ◽  
Multi Layer Perceptron ◽  
Numerical Instability ◽  
Z Score ◽  
Score Normalization

Abstract We tested Artificial Neural Networks (ANNs) to predict a fully-developed turbulent channel flow of a viscoelastic fluid in preparation for elucidating flow phenomenon and solving the difficulty in DNS (Direct Numerical Simulation) due to numerical instability of the viscoelastic fluid. Two kinds of ANNs (multi-layer perceptron (MLP) and U-Net) were trained using DNS data to predict conformation stress from given instantaneous field. The MLP showed accurate predictions and predictions got better with z-score normalization. ANN predicted accurately in near-wall region having coherent structures. In addition, we demonstrated that ANN get the nonlinear relationship between velocity gradient and viscoelastic stress partially.

Assessing the Effects of Near Wall Corrections of the Force Acting on Particles in Gas-Solid Channel Flows

2005 ◽  
Author(s):  
Boris Arcen ◽  
Anne Tanie`re ◽  
Benoiˆt Oesterle´
Keyword(s):  
Channel Flow ◽  
Lift Force ◽  
Particle Concentration ◽  
Turbulent Channel Flow ◽  
Shear Velocity ◽  
Solid Particles ◽  
Wall Region ◽  
Wall Effects ◽  
Strong Shear ◽  
Near Wall

The importance of using the lift force and wall-corrections of the drag coefficient for modeling the motion of solid particles in a fully-developed channel flow is investigated by means of direct numerical simulation (DNS). The turbulent channel flow is computed at a Reynolds number based on the wall-shear velocity and channel half-width of 185. Contrary to most of the numerical simulations, we consider in the present study a lift force formulation that accounts for the weak and strong shear as well as for the wall effects (hereinafter referred to as optimum lift force), and the wall-corrections of the drag force. The DNS results show that the optimum lift force and the wall-corrections of the drag together have little influence on most of the statistics (particle concentration, mean velocities, and mean relative and drift velocities), even in the near wall region.

Deposition of Small Particles From Turbulent Flows

2003 ◽  
Author(s):  
Z. Wu ◽  
J. B. Young
Keyword(s):  
Turbulent Flow ◽  
Turbulent Flows ◽  
Channel Flow ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Numerical Study ◽  
Turbulent Channel Flow ◽  
Brownian Diffusion ◽  
Small Particles ◽  
Two Fluid

This paper deals with particle deposition onto solid walls from turbulent flows. The aim of the study is to model particle deposition in industrial flows, such as the one in gas turbines. The numerical study has been carried out with a two fluid approach. The possible contribution to the deposition from Brownian diffusion, turbulent diffusion and shear-induced lift force are considered in the study. Three types of turbulent two-phase flows have been studied: turbulent channel flow, turbulent flow in a bent duct and turbulent flow in a turbine blade cascade. In the turbulent channel flow case, the numerical results from a two-dimensional code show good agreement with numerical and experimental results from other resources. Deposition problem in a bent duct flow is introduced to study the effect of curvature. Finally, the deposition of small particles on a cascade of turbine blades is simulated. The results show that the current two fluid models are capable of predicting particle deposition rates in complex industrial flows.

Direct Numerical Simulation of Passive Scalar Field in a Turbulent Channel Flow

1992 ◽  
Vol 114 (3) ◽  
pp. 598-606 ◽  
Author(s):  
N. Kasagi ◽  
Y. Tomita ◽  
A. Kuroda
Keyword(s):  
Numerical Simulation ◽  
Direct Numerical Simulation ◽  
Channel Flow ◽  
Turbulent Channel Flow ◽  
Passive Scalar ◽  
Streamwise Velocity ◽  
Heat Fluxes ◽  
Wall Region ◽  
Turbulent Heat ◽  
Turbulent Heat Fluxes

A direct numerical simulation (DNS) of the fully developed thermal field in a two-dimensional turbulent channel flow of air was carried out. The isoflux condition was imposed on the two walls so that the local mean temperature increased linearly in the streamwise direction. With any buoyancy effect neglected, temperature was considered as a passive scalar. The computation was executed on 1,589,248 grid points by using a spectral method. The statistics obtained were root-mean-square temperature fluctuations, turbulent heat fluxes, turbulent Prandtl number, and dissipation time scales. They agreed fairly well with existing experimental and numerical simulation data. Each term in the budget equations of temperature variance, its dissipation rate, and turbulent heat fluxes was also calculated. It was found that the temperature fluctuation θ′ was closely correlated with the streamwise velocity fluctuation u′, particularly in the near-wall region. Hence, the distribution of budget terms for the streamwise and wall-normal heat fluxes, u′θ′ and v′θ′, were very similar to those for the two Reynolds stress components, u′u′ and u′v′.

Sign in / Sign up

Export Citation Format

Share Document