scholarly journals Destabilisation and modification of Tollmien–Schlichting disturbances by a three-dimensional surface indentation

2017 ◽  
Vol 819 ◽  
pp. 592-620 ◽  
Author(s):  
Hui Xu ◽  
Shahid M. Mughal ◽  
Erwin R. Gowree ◽  
Chris J. Atkin ◽  
Spencer J. Sherwin
Keyword(s):  
Boundary Layer ◽  
Linear Models ◽  
Flow Instability ◽  
Separation Bubble ◽  
Three Dimensional ◽  
Symmetry Plane ◽  
Nonlinear Behaviour ◽  
Numerical Work ◽  
Tollmien Schlichting ◽  
Topological Changes

We consider the influence of a smooth three-dimensional (3-D) indentation on the instability of an incompressible boundary layer by linear and nonlinear analyses. The numerical work was complemented by an experimental study to investigate indentations of approximately $11\unicode[STIX]{x1D6FF}_{99}$ and $22\unicode[STIX]{x1D6FF}_{99}$ width at depths of 45 %, 52 % and 60 % of $\unicode[STIX]{x1D6FF}_{99}$, where $\unicode[STIX]{x1D6FF}_{99}$ indicates 99% boundary layer thickness. For these indentations a separation bubble confined within the indentation arises. Upstream of the indentation, spanwise-uniform Tollmien–Schlichting (TS) waves are assumed to exist, with the objective to investigate how the 3-D surface indentation modifies the 2-D TS disturbance. Numerical corroboration against experimental data reveals good quantitative agreement. Comparing the structure of the 3-D separation bubble to that created by a purely 2-D indentation, there are a number of topological changes particularly in the case of the widest indentation; more rapid amplification and modification of the upstream TS waves along the symmetry plane of the indentation is observed. For the shortest indentations, beyond a certain depth there are then no distinct topological changes of the separation bubbles and hence on flow instability. The destabilising mechanism is found to be due to the confined separation bubble and is attributed to the inflectional instability of the separated shear layer. Finally for the widest width indentation investigated ($22\unicode[STIX]{x1D6FF}_{99}$), results of the linear analysis are compared with direct numerical simulations. A comparison with the traditional criteria of using $N$-factors to assess instability of properly 3-D disturbances reveals that a general indication of flow destabilisation and development of strongly nonlinear behaviour is indicated as $N=6$ values are attained. However $N$-factors, based on linear models, can only be used to provide indications and severity of the destabilisation, since the process of disturbance breakdown to turbulence is inherently nonlinear and dependent on the magnitude and scope of the initial forcing.

Acoustic receptivity and evolution of two-dimensional and oblique disturbances in a Blasius boundary layer

2001 ◽  
Vol 432 ◽  
pp. 69-90 ◽  
Author(s):  
RUDOLPH A. KING ◽  
KENNETH S. BREUER
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Acoustic Wave ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Surface Waviness ◽  
S Wave ◽  
Boundary Layer Instability ◽  
Blasius Boundary Layer ◽  
Tollmien Schlichting

An experimental investigation was conducted to examine acoustic receptivity and subsequent boundary-layer instability evolution for a Blasius boundary layer formed on a flat plate in the presence of two-dimensional and oblique (three-dimensional) surface waviness. The effect of the non-localized surface roughness geometry and acoustic wave amplitude on the receptivity process was explored. The surface roughness had a well-defined wavenumber spectrum with fundamental wavenumber kw. A planar downstream-travelling acoustic wave was created to temporally excite the flow near the resonance frequency of an unstable eigenmode corresponding to kts = kw. The range of acoustic forcing levels, ε, and roughness heights, Δh, examined resulted in a linear dependence of receptivity coefficients; however, the larger values of the forcing combination εΔh resulted in subsequent nonlinear development of the Tollmien–Schlichting (T–S) wave. This study provides the first experimental evidence of a marked increase in the receptivity coefficient with increasing obliqueness of the surface waviness in excellent agreement with theory. Detuning of the two-dimensional and oblique disturbances was investigated by varying the streamwise wall-roughness wavenumber αw and measuring the T–S response. For the configuration where laminar-to-turbulent breakdown occurred, the breakdown process was found to be dominated by energy at the fundamental and harmonic frequencies, indicative of K-type breakdown.

Generation of steady longitudinal vortices in hypersonic boundary layer

2013 ◽  
Vol 729 ◽  
pp. 702-731 ◽  
Author(s):  
A. I. Ruban ◽  
M. A. Kravtsova
Keyword(s):  
Boundary Layer ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Viscosity Coefficient ◽  
Momentum Equation ◽  
The Body ◽  
Nonlinear Behaviour ◽  
Hypersonic Boundary Layer ◽  
Stagnation Temperature ◽  
Characteristic Distance

AbstractIn this paper we study the three-dimensional perturbations produced in a hypersonic boundary layer by a small wall roughness. The flow analysis is performed under the assumption that the Reynolds number, $R{e}_{0} = {\rho }_{\infty } {V}_{\infty } L/ {\mu }_{0} $, and Mach number, ${M}_{\infty } = {V}_{\infty } / {a}_{\infty } $, are large, but the hypersonic interaction parameter, $\chi = { M}_{\infty }^{2} R{ e}_{0}^{- 1/ 2} $, is small. Here ${V}_{\infty } $, ${\rho }_{\infty } $ and ${a}_{\infty } $ are the flow velocity, gas density and speed of sound in the free stream, ${\mu }_{0} $ is the dynamic viscosity coefficient at the ‘stagnation temperature’, and $L$ is the characteristic distance the boundary layer develops along the body surface before encountering a roughness. We choose the longitudinal and spanwise dimensions of the roughness to be $O({\chi }^{3/ 4} )$ quantities. In this case the flow field around the roughness may be described in the framework of the hypersonic viscous–inviscid interaction theory, also known as the triple-deck model. Our main interest in this paper is the nonlinear behaviour of the perturbations. We study these by means of numerical solution of the triple-deck equations, for which purpose a modification of the ‘skewed shear’ technique suggested by Smith (United Technologies Research Center Tech. Rep. 83-46, 1983) has been used. The technique requires global iterations to adjust the viscous and inviscid parts of the flow. Convergence of such iterations is known to be a major problem in viscous–inviscid calculations. In order to achieve improved stability of the method, both the momentum equation for the viscous part of the flow, and the equations describing the interaction with the flow outside the boundary layer, are treated implicitly in this study. The calculations confirm the fact that in this sort of flow the perturbations are capable of propagating upstream in the boundary layer, resulting in a perturbation field which surrounds the roughness on all sides. We found that the perturbations decay rather fast with the distance from the roughness everywhere except in the wake behind the roughness. We found that if the height of the roughness is small, then the perturbations also decay in the wake, though much more slowly than outside the wake. However, if the roughness height exceeds some critical value, then two symmetric counter-rotating vortices form in the wake. They appear to support themselves and grow as the distance from the roughness increases.

Numerical simulation of boundary-layer transition and transition control

1989 ◽  
Vol 199 ◽  
pp. 403-440 ◽  
Author(s):  
E. Laurien ◽  
L. Kleiser
Keyword(s):  
Boundary Layer ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Transition Process ◽  
Numerical Results ◽  
Boundary Layer Transition ◽  
Two Dimensional ◽  
Layer Transition ◽  
Longitudinal Vortices ◽  
Tollmien Schlichting

The laminar-turbulent transition process in a parallel boundary-layer with Blasius profile is simulated by numerical integration of the three-dimensional incompressible Navier-Stokes equations using a spectral method. The model of spatially periodic disturbances developing in time is used. Both the classical Klebanoff-type and the subharmonic type of transition are simulated. Maps of the three-dimensional velocity and vorticity fields and visualizations by integrated fluid markers are obtained. The numerical results are compared with experimental measurements and flow visualizations by other authors. Good qualitative and quantitative agreement is found at corresponding stages of development up to the one-spike stage. After the appearance of two-dimensional Tollmien-Schlichting waves of sufficiently large amplitude an increasing three-dimensionality is observed. In particular, a peak-valley structure of the velocity fluctuations, mean longitudinal vortices and sharp spike-like instantaneous velocity signals are formed. The flow field is dominated by a three-dimensional horseshoe vortex system connected with free high-shear layers. Visualizations by time-lines show the formation of A-structures. Our numerical results connect various observations obtained with different experimental techniques. The initial three-dimensional steps of the transition process are consistent with the linear theory of secondary instability. In the later stages nonlinear interactions of the disturbance modes and the production of higher harmonics are essential.We also study the control of transition by local two-dimensional suction and blowing at the wall. It is shown that transition can be delayed or accelerated by superposing disturbances which are out of phase or in phase with oncoming Tollmien-Schlichting instability waves, respectively. Control is only effective if applied at an early, two-dimensional stage of transition. Mean longitudinal vortices remain even after successful control of the fluctuations.

scholarly journals Receptivity of a laminar boundary layer to the interaction of a three-dimensional roughness element with time-harmonic free-stream disturbances

1992 ◽  
Vol 242 ◽  
pp. 701-720 ◽  
Author(s):  
M. Tadjfar ◽  
R. J. Bodonyi
Keyword(s):  
Boundary Layer ◽  
Laminar Boundary Layer ◽  
Stokes Flow ◽  
Free Stream ◽  
Flow Direction ◽  
Roughness Element ◽  
Three Dimensional ◽  
Unsteady Motion ◽  
Time Harmonic ◽  
Tollmien Schlichting

Receptivity of a laminar boundary layer to the interaction of time-harmonic free-stream disturbances with a three-dimensional roughness element is studied. The three-dimensional nonlinear triple–deck equations are solved numerically to provide the basic steady-state motion. At high Reynolds numbers, the governing equations for the unsteady motion are the unsteady linearized three-dimensional triple-deck equations. These equations can only be solved numerically. In the absence of any roughness element, the free-stream disturbances, to the first order, produce the classical Stokes flow, in the thin Stokes layer near the wall (on the order of our lower deck). However, with the introduction of a small three-dimensional roughness element, the interaction between the hump and the Stokes flow introduces a spectrum of all spatial disturbances inside the boundary layer. For supercritical values of the scaled Strouhal number, S0 > 2, these Tollmien–Schlichting waves are amplified in a wedge-shaped region, 15° to 18° to the basic-flow direction, extending downstream of the hump. The amplification rate approaches a value slightly higher than that of two-dimensional Tollmien–Schlichting waves, as calculated by the linearized analysis, far downstream of the roughness element.

scholarly journals Experimental and theoretical study of swept-wing boundary-layer instabilities. Three-dimensional Tollmien-Schlichting instability

2019 ◽  
Vol 31 (11) ◽  
pp. 114104
Author(s):  
V. I. Borodulin ◽  
A. V. Ivanov ◽  
Y. S. Kachanov ◽  
D. A. Mischenko ◽  
R. Örlü ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Theoretical Study ◽  
Three Dimensional ◽  
Swept Wing ◽  
Tollmien Schlichting

Leading-edge receptivity of a hypersonic boundary layer on a flat plate

2001 ◽  
Vol 426 ◽  
pp. 73-94 ◽  
Author(s):  
A. A. MASLOV ◽  
A. N. SHIPLYUK ◽  
A. A. SIDORENKO ◽  
D. ARNAL
Keyword(s):  
Boundary Layer ◽  
Acoustic Waves ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Experimental Investigations ◽  
Two Dimensional ◽  
Inclination Angles ◽  
Tollmien Schlichting ◽  
Radiation Conditions

Experimental investigations of the boundary layer receptivity, on the sharp leading edge of a at plate, to acoustic waves induced by two-dimensional and three- dimensional perturbers, have been performed for a free-stream Mach number M∞ = 5.92. The fields of controlled free-stream disturbances were studied. It was shown that two-dimensional and three-dimensional perturbers radiate acoustic waves and that these perturbers present a set of harmonic motionless sources and moving sources with constant amplitude. The disturbances excited in the boundary layer were measured. It was found that acoustic waves impinging on the leading edge generate Tollmien–Schlichting waves in the boundary layer. The receptivity coefficients were obtained for several radiation conditions and intensities. It was shown that there is a dependence of receptivity coefficients on the wave inclination angles.

The three-dimensional stability of boundary-layer flow over compliant walls

1992 ◽  
Vol 238 ◽  
pp. 537-577 ◽  
Author(s):  
K. S. Yeo
Keyword(s):  
Boundary Layer ◽  
Eigenvalue Problem ◽  
Growth Rates ◽  
Isotropic Material ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Material Anisotropy ◽  
Compliant Walls ◽  
Tollmien Schlichting ◽  
Disturbance Growth

This paper examines the linear stability of the Blasius boundary layer over compliant walls to three-dimensional (oblique) disturbance wave modes. The formulation of the eigenvalue problem is applicable to compliant walls possessing general material anisotropy. Isotropic-material walls and selected classes of anisotropic-material walls are studied. When the properties of the wall are identical with respect to all oblique wave directions, the stability eigenvalue problem for unstable three-dimensional wave modes may be reduced to an equivalent problem for two-dimensional modes. The results for isotropic-material walls show that three-dimensional Tollmien–Schlichting instability modes are more dominant than their two-dimensional counterparts when the walls are sufficiently compliant. The critical Reynolds number for Tollmien-Schlichting instability may be given by three-dimensional modes. Furthermore, for highly compliant walls, calculations based solely on two-dimensional modes are likely to underestimate the maximum disturbance growth factor needed for transition prediction and correlation. However, because the disturbance growth rates on highly compliant walls are much lower than those on a rigid wall, significant delay of transition may still be possible provided compliance-induced instabilities are properly suppressed. Walls featuring material anisotropy which have reduced stiffness to shear deformation in the transverse and oblique planes are also investigated. Such anisotropy is found to be effective in reducing the growth rates of the three-dimensional modes relative to those of the two-dimensional modes.

Direct Numerical Simulations of Transitional Separation–Bubble Development in Swept–Blade Flow Conditions

2012 ◽  
Author(s):  
Joshua R. Brinkerhoff ◽  
Metin I. Yaras
Keyword(s):  
Boundary Layer ◽  
Numerical Simulations ◽  
Shear Layer ◽  
Pressure Field ◽  
Separation Bubble ◽  
Three Dimensional ◽  
Direct Numerical Simulations ◽  
Small Scale ◽  
Flow Conditions ◽  
Crossflow Instability

This paper describes numerical simulations of the instability mechanisms in a separation bubble subjected to a three-dimensional freestream pressure distribution. Two direct numerical simulations are performed of a separation bubble with laminar separation and turbulent reattachment under low freestream turbulence at flow Reynolds numbers and streamwise pressure distributions that approximate the conditions encountered on the suction side of typical low-pressure gas-turbine blades with blade sweep angles of 0° and 45°. The three-dimensional pressure field in the swept configuration produces a crossflow-velocity component in the laminar boundary layer upstream of the separation point that is unstable to a crossflow instability mode. The simulation results show that crossflow instability does not play a role in the development of the boundary layer upstream of separation. An increase in the amplification rate and most amplified disturbance frequency is observed in the separated-flow region of the swept configuration, and is attributed to boundary-layer conditions at the point of separation that are modified by the spanwise pressure gradient. This results in a slight upstream movement of the location where the shear layer breaks down to small-scale turbulence and modifies the turbulent mixing of the separated shear layer to yield a downstream shift in the time-averaged reattachment location. The results demonstrate that although crossflow instability does not appear to have a noticeable effect on the development of the transitional separation bubble, the 3D pressure field does indirectly alter the separation-bubble development by modifying the flow conditions at separation.

The boundary layer due to a three-dimensional vortex loop

1987 ◽  
Vol 185 ◽  
pp. 569-598 ◽  
Author(s):  
S. Ersoy ◽  
J. D. A. Walker
Keyword(s):  
Boundary Layer ◽  
Three Dimensional ◽  
Symmetry Plane ◽  
Layer Growth ◽  
Plane Wall ◽  
Vortex Loop ◽  
Loop Shape ◽  
Layer Flow ◽  
Boundary Layer Growth ◽  
Moving Vortex

The nature of the boundary layer induced by the motion of a three-dimensional vortex loop towards a plane wall is considered. Initially the vortex is taken to be a ring approaching a plane wall at an angle of attack in an otherwise stagnant fluid; the ring rapidly distorts into a loop shape due to the influence of the wall and the trajectory is computed from a numerical solution of the Biot-Savart integral. As the vortex loop moves, an unsteady boundary-layer flow develops on the wall. A method is described which allows the computation of the flow velocities on and near the symmetry plane of the vortex loop within the boundary layer. The computed results show the development of a variety of complex three-dimensional separation phenomena. Some of the solutions ultimately show strong localized boundary-layer growth and are suggestive that a boundary-layer eruption and a strong viscous-inviscid interaction will be induced by the moving vortex.

Sign in / Sign up

Export Citation Format

Share Document