scholarly journals Effect of surface contamination on interfacial mass transfer rate

2017 ◽  
Vol 830 ◽  
pp. 5-34 ◽  
Author(s):  
J. G. Wissink ◽  
H. Herlina ◽  
Y. Akar ◽  
M. Uhlmann
Keyword(s):  
Mass Transfer ◽  
Transfer Rate ◽  
Isotropic Turbulence ◽  
Mass Transfer Rate ◽  
Surface Contamination ◽  
Gas Transfer ◽  
Clean Surface ◽  
Transfer Velocity ◽  
Surface Fraction ◽  
Interfacial Mass Transfer

The influence of surface contamination upon the mass transfer rate of a low diffusivity gas across a flat surface is studied using direct numerical simulations. The interfacial mass transfer is driven by isotropic turbulence diffusing from below. Similar to Shen et al. (J. Fluid Mech., vol. 506, 2004, pp. 79–115) the surface contamination is modelled by relating the normal gradient of the horizontal velocities at the top to the horizontal gradients of the surfactant concentrations. A broad range of contamination levels is considered, including clean to severely contaminated conditions. The time-averaged results show a strong correlation between the gas transfer velocity and the clean surface fraction of the surface area. In the presence of surface contamination the mass transfer velocity $K_{L}$ is found to scale as a power of the Schmidt number, i.e. $Sc^{-q}$, where $q$ smoothly transitions from $q=1/2$ for clean surfaces to $q=2/3$ for very dirty interfaces. A power law $K_{L}\propto Sc^{-q}$ is proposed in which both the exponent $q$ and the constant of proportionality become functions of the clean surface fraction.

scholarly journals Direct numerical simulation of turbulent scalar transport across a flat surface

2014 ◽  
Vol 744 ◽  
pp. 217-249 ◽  
Author(s):  
H. Herlina ◽  
J. G. Wissink
Keyword(s):  
Mass Transfer ◽  
Isotropic Turbulence ◽  
Reynolds Numbers ◽  
Gas Transfer ◽  
Computational Domain ◽  
Atmospheric Gases ◽  
Transfer Velocity ◽  
Physical Mechanisms ◽  
Schmidt Numbers ◽  
Large Eddies

AbstractTo elucidate the physical mechanisms that play a role in the interfacial transfer of atmospheric gases into water, a series of direct numerical simulations of mass transfer across the air–water interface driven by isotropic turbulence diffusing from below has been carried out for various turbulent Reynolds numbers ($R_T=84,195,507$). To allow a direct (unbiased) comparison of the instantaneous effects of scalar diffusivity, in each of the DNS up to six scalar advection–diffusion equations with different Schmidt numbers were solved simultaneously. As far as the authors are aware this is the first simulation that is capable to accurately resolve the realistic Schmidt number, $\mathit{Sc}=500$, that is typical for the transport of atmospheric gases such as oxygen in water. For the range of turbulent Reynolds numbers and Schmidt numbers considered, the normalized transfer velocity $K_L$ was found to scale with $R_T^{-{1/2}}$ and $\mathit{Sc}^{-{1/2}}$, which indicates that the largest eddies present in the isotropic turbulent flow introduced at the bottom of the computational domain tend to determine the mass transfer. The $K_L$ results were also found to be in good agreement with the surface divergence model of McCready, Vassiliadou & Hanratty (AIChE J., vol. 32, 1986, pp. 1108–1115) when using a constant of proportionality of 0.525. Although close to the surface large eddies are responsible for the bulk of the gas transfer, it was also observed that for higher $R_T$ the influence of smaller eddies becomes more important.

Effect of Mild Sway on the Interfacial Mass Transfer Rate of Stored Liquids

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Dibakar Rakshit ◽  
K. P. Thiagarajan ◽  
R. Narayanaswamy
Keyword(s):  
Mass Transfer ◽  
Transfer Rate ◽  
Degrees Of Freedom ◽  
Mass Transfer Rate ◽  
Constant Amplitude ◽  
Two Phase ◽  
Interfacial Mass Transfer ◽  
Different Temperatures ◽  
Slow Moving ◽  
Liquid Vapor

An exploratory study of two-phase physics was undertaken in a slow moving tank containing liquid. This study is under the regime of conjugate heat and mass transfer phenomena. An experiment was designed and performed to estimate the interfacial mass transfer characteristics of a slowly moving tank. The tank was swayed at varying frequencies and constant amplitude. The experiments were conducted for a range of liquid temperatures and filling levels. The experimental setup consisted of a tank partially filled with water at different temperatures, being swayed using a six degrees-of-freedom (DOF) motion actuator. The experiments were conducted for a frequency range of 0.7–1.6 Hz with constant amplitude of 0.025 m. The evaporation of liquid from the interface and the gaseous condensation was quantified by calculating the instantaneous interfacial mass transfer rate of the slow moving tank. The dependence of interfacial mass transfer rate on the liquid–vapor interfacial temperature, the fractional concentration of the evaporating liquid, the surface area of the liquid vapor interface and the filling level of the liquid was established. As sway frequency, filling levels, and liquid temperature increased, the interfacial mass transfer rate also increased. The interfacial mass transfer rate estimated for the swaying tank compared with the interfacial mass transfer rate of stationary tank shows that vibration increases the mass transfer.

Characterization of Interfacial Mass Transfer Rate of Stored Liquids

2015 ◽  
Vol 7 (2) ◽  
Author(s):  
Dibakar Rakshit ◽  
R. Narayanaswamy ◽  
K. P. Thiagarajan
Keyword(s):  
Mass Transfer ◽  
Transfer Rate ◽  
Mass Transfer Rate ◽  
Two Phase ◽  
Interfacial Mass Transfer ◽  
Different Temperatures ◽  
Interfacial Temperature ◽  
Fill Level ◽  
Liquid Vapor

A thermodynamic analysis of the two-phase physics involving a liquid–vapor combination has been studied under the regime of conjugate heat and mass transfer phenomena. An experiment has been designed and performed to estimate the interfacial mass transfer characteristics of a liquid–vapor system by varying the liquid temperature. The experimental setup consists of an instrumented tank partially filled with water and maintained at different temperatures. The evaporation of liquid from the interface and the gaseous condensation has been quantified by calculating the interfacial mass transfer rate for both covered and uncovered tanks. The dependence of interfacial mass transfer rate on the liquid–vapor interfacial temperature, fractional concentration of the evaporating liquid, the surface area of the liquid vapor interface, and the fill level of the liquid has been established through the present experimental study. An estimation of the overall mass transfer rate from the interface due to a concentration gradient shows an analogy with the multiphase heat transfer that takes place across the interface due to temperature gradient. It was seen that at low fill levels and with a temperature difference of about 30 °C between liquid and ullage, the mass transfer rate of a closed system was nearly doubled when compared to its open system counterpart.

scholarly journals Isotropic-turbulence-induced mass transfer across a severely contaminated water surface

2016 ◽  
Vol 797 ◽  
pp. 665-682 ◽  
Author(s):  
H. Herlina ◽  
J. G. Wissink
Keyword(s):  
Mass Transfer ◽  
Schmidt Number ◽  
Isotropic Turbulence ◽  
Slip Boundary Condition ◽  
Gas Transfer ◽  
Transfer Velocity ◽  
Slip Conditions ◽  
Slip Boundary ◽  
Turbulent Reynolds Number ◽  
Solid Liquid

Direct numerical simulations were performed to investigate the effect of severe contamination on interfacial gas transfer in the presence of isotropic turbulence diffusing from below. A no-slip boundary condition was employed at the interface to model the severe contamination effect. The influence of both Schmidt number ($Sc$) and turbulent Reynolds number ($R_{T}$) on the transfer velocity ($K_{L}$) was studied. In the range from $Sc=2$ up to $Sc=500$ it was found that $K_{L}\propto Sc^{-2/3}$, which is in agreement with predictions based on solid–liquid transport models, see e.g. Davies (1972, Turbulence Phenomena, Academic). For similar $R_{T}$, the transfer velocity was observed to reduce significantly compared with the free-slip conditions. The reduction becomes more pronounced with increasing Schmidt number. Similar to the observation for free-slip conditions made by Theofanous et al. (Intl J. Heat Mass Transfer, vol. 19 (6), 1976, pp. 613–624), the normalized $K_{L}$ in the present no-slip case was also found to depend on $R_{T}^{-1/2}$ and $R_{T}^{-1/4}$ for small and large turbulent Reynolds numbers, respectively.

Free Convective Mass Transfer at Isosceles Triangular Surfaces of Varying Inclination

2003 ◽  
Vol 68 (11) ◽  
pp. 2080-2092 ◽  
Author(s):  
Martin Keppert ◽  
Josef Krýsa ◽  
Anthony A. Wragg
Keyword(s):  
Mass Transfer ◽  
Transfer Rate ◽  
Mass Transfer Rate ◽  
Mass Transfer Process ◽  
Sulfate Solution ◽  
Convective Mass Transfer ◽  
Varying Length ◽  
Inclined Surface ◽  
Vertical Case ◽  
Limiting Diffusion Current

The limiting diffusion current technique was used for investigation of free convective mass transfer at down-pointing up-facing isosceles triangular surfaces of varying length and inclination. As the mass transfer process, copper deposition from acidified copper(II) sulfate solution was used. It was found that the mass transfer rate increases with inclination from the vertical to the horizontal position and decreases with length of inclined surface. Correlation equations for 7 angles from 0 to 90° were found. The exponent in the ShL-RaL correlation ranged from 0.247 for the vertical case, indicating laminar flow, to 0.32 for inclinations of 60 to 90°, indicating mixed or turbulent flow. The general correlation ShL = 0.358(RaL sin θ)0.30 for the RaL sin θ range from 7 × 106 to 2 × 1011 and inclination range from 15 to 90° was obtained.

Distributed mass transfer rate for modelling the leaching of porous granular materials containing soluble pollutants

2000 ◽  
Vol 55 (7) ◽  
pp. 1257-1267 ◽  
Author(s):  
Tiruta-Barna Ligia ◽  
Barna Radu ◽  
Moszkowicz Pierre ◽  
Bae Hae-Ryong
Keyword(s):  
Mass Transfer ◽  
Granular Materials ◽  
Transfer Rate ◽  
Mass Transfer Rate

Enhancement of formic acid production from CO2 in formate dehydrogenase reaction using nanoparticles

RSC Advances ◽  
2016 ◽  
Vol 6 (111) ◽  
pp. 109978-109982 ◽  
Author(s):  
Young-Kee Kim ◽  
Sung-Yeob Lee ◽  
Byung-Keun Oh
Keyword(s):  
Mass Transfer ◽  
Formic Acid ◽  
Acid Production ◽  
Transfer Rate ◽  
Formate Dehydrogenase ◽  
Mass Transfer Rate ◽  
Liquid Mass ◽  
Dehydrogenase Reaction ◽  
Liquid Mass Transfer ◽  
Mesoporous Nanoparticles

In an enzyme process using a gas substrate, the enhanced gas liquid mass transfer rate of the gas substrate by methyl-functionalized mesoporous nanoparticles could improve the productivity.

Sign in / Sign up

Export Citation Format

Share Document