scholarly journals Trailing-edge flow and noise control using porous treatments

2018 ◽  
Vol 850 ◽  
pp. 83-119 ◽  
Author(s):  
Syamir Alihan Showkat Ali ◽  
Mahdi Azarpeyvand ◽  
Carlos Roberto Ilário da Silva
Keyword(s):  
Boundary Layer ◽  
Vortex Shedding ◽  
Aerodynamic Noise ◽  
Near Wake ◽  
Recirculating Flow ◽  
Flow Interaction ◽  
Layer Structures ◽  
Trailing Edges ◽  
Blunt Edge ◽  
Vortex Shedding Frequency

This paper is concerned with the application of porous treatments as a means of flow and aerodynamic noise reduction. An extensive experimental investigation is undertaken to study the effects of flow interaction with porous media, in particular in the context of the manipulation of flow over blunt trailing edges and attenuation of vortex shedding. Comprehensive boundary layer and wake measurements have been carried out for a long flat plate with solid and porous blunt trailing edges. Unsteady velocity and surface pressure measurements have also been performed to gain an in-depth understanding of the changes to the energy–frequency content and coherence of the boundary layer and wake structures as a result of the flow interaction with a porous treatment. Results have shown that permeable treatments can effectively delay the vortex shedding and stabilize the flow over the blunt edge via mechanisms involving flow penetration into the porous medium and discharge into the near-wake region. It has also been shown that the porous treatment can effectively destroy the spanwise coherence of the boundary layer structures and suppress the velocity and pressure coherence, particularly at the vortex shedding frequency. The flow–porous scrubbing and its effects on the near-wall and large coherent structures have also been studied. The emergence of a quasi-periodic recirculating flow field inside highly permeable surface treatments has also been investigated. Finally, the paper has identified several important mechanisms concerning the application of porous treatments for aerodynamic and aeroacoustic purposes, which can help more effective and tailored designs for specific applications.

The Influence of Boundary Layer Velocity Gradients and Bed Proximity on Vortex Shedding From Free Spanning Pipelines

1984 ◽  
Vol 106 (1) ◽  
pp. 70-78 ◽  
Author(s):  
A. J. Grass ◽  
P. W. J. Raven ◽  
R. J. Stuart ◽  
J. A. Bray
Keyword(s):  
Boundary Layer ◽  
Strouhal Number ◽  
Vortex Shedding ◽  
Combined Effects ◽  
Maximum Increase ◽  
Velocity Gradients ◽  
Large Velocity ◽  
Layer Velocity ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

The paper summarizes the results of a laboratory study of the separate and combined effects of bed proximity and large velocity gradients on the frequency of vortex shedding from pipeline spans immersed in the thick boundary layers of tidal currents. This investigation forms part of a wider project concerned with the assessment of span stability. The measurements show that in the case of both sheared and uniform approach flows, with and without velocity gradients, respectively, the Strouhal number defining the vortex shedding frequency progressively increases as the gap between the pipe base and the bed is reduced below two pipe diameters. The maximum increase in vortex shedding Strouhal number, recorded close to the bed in an approach flow with large velocity gradients, was of the order of 25 percent.

Vortex-Induced Vibration for Heat Transfer Enhancement

2014 ◽  
Author(s):  
Junxiang Shi ◽  
Steven R. Schafer ◽  
Chung-Lung (C. L. ) Chen
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Transfer Enhancement ◽  
Natural Frequency ◽  
Vortex Shedding ◽  
Pressure Loss ◽  
Thermal Boundary Layer ◽  
Transfer Enhancement ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

A passive, self-agitating method which takes advantage of vortex-induced vibration (VIV) is presented to disrupt the thermal boundary layer and thereby enhance the convective heat transfer performance of a channel. A flexible cylinder is placed at centerline of a channel. The vortex shedding due to the presence of the cylinder generates a periodic lift force and the consequent vibration of the cylinder. The fluid-structure-interaction (FSI) due to the vibration strengthens the disruption of the thermal boundary layer by reinforcing vortex interaction with the walls, and improves the mixing process. This novel concept is demonstrated by a three-dimensional modeling study in different channels. The fluid dynamics and thermal performance are discussed in terms of the vortex dynamics, disruption of the thermal boundary layer, local and average Nusselt numbers (Nu), and pressure loss. At different conditions (Reynolds numbers, channel geometries, material properties), the channel with the VIV is seen to significantly increase the convective heat transfer coefficient. When the Reynolds number is 168, the channel with the VIV improves the average Nu by 234.8% and 51.4% in comparison with a clean channel and a channel with a stationary cylinder, respectively. The cylinder with the natural frequency close to the vortex shedding frequency is proved to have the maximum heat transfer enhancement. When the natural frequency is different from the vortex shedding frequency, the lower natural frequency shows a higher heat transfer rate and lower pressure loss than the larger one.

Stability properties of forced wakes

2007 ◽  
Vol 579 ◽  
pp. 137-161 ◽  
Author(s):  
B. THIRIA ◽  
J. E. WESFREID
Keyword(s):  
Vortex Shedding ◽  
Mean Flow ◽  
Near Wake ◽  
Global Mode ◽  
Spatial Properties ◽  
Moderate Reynolds Number ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
The Stability ◽  
Selection Of

Thiria, Goujon-Durand & Wesfreid (J. Fluid Mech. vol. 560, 2006, p. 123), it was shown that vortex shedding from a rotationally oscillating cylinder at moderate Reynolds number can be characterized by the spatial coexistence of two distinct patterns, one of which is related to the forcing frequency in the near wake and the other to a frequency close to the natural one for the unforced case downstream of this locked region. The existence and the modification of these wake characteristics were found to be strongly affected by the frequency and the amplitude of the cylinder oscillation. In this paper, a linear stability analysis of these forced regimes is performed, and shows that the stability characteristics of such flows are governed by a strong mean flow correction which is a function of the oscillation parameters. We also present experiments on the spatial properties of the global mode and on the selection of the vortex shedding frequency as a function of the forcing conditions for Re = 150. Finally, we elucidate a diagram of locked and non-locked states, for a large range of frequencies and amplitudes of the oscillation.

Flow Around a Normal Plate of Finite Width Immersed in a Turbulent Boundary Layer

1983 ◽  
Vol 105 (1) ◽  
pp. 98-104 ◽  
Author(s):  
H. Sakamoto ◽  
M. Arie
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Turbulent Boundary Layer ◽  
Power Function ◽  
Vortex Shedding ◽  
Stream Velocity ◽  
Finite Width ◽  
Pressure Drag ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

An experimental investigation was carried out on the flow around a normal plate of finite width mounted on a smooth plane wall along which a turbulent boundary layer was fully developed. Experimental data were collected to investigate the effects of (1) the aspect ratio of the plate (2) the parameters characterizing the boundary-layer on the pressure drag and the vortex shedding frequency. The pressure drag coefficient of the plate defined by CDτ = D/(1/2ρuτ2hw) was found to be expressed by a power function of huτ/ν in the range h/δ<1.0 for each aspect ratio w/h, where D is the pressure drag, uτ is the shear velocity, ρ is the density of fluid, h and w are the height and the width of the plate, respectively, ν is the kinematic viscosity, δ is the thickness of the boundary layer. Also, the Strouhal number for the plate defined by St =fc • w/ U0 was found to be expressed by a power function of the aspect ratio w/h in the range of h/δ less than about 1.0, where fc is the vortex shedding frequency, U0 is the free-stream velocity. As the aspect ratio was reduced, the type of vortex shedding behind the plate was found to change from the arch type to the Karman type at the aspect ratio of about 0.8.

Vortex shedding from a rectangular prism and a circular cylinder placed vertically in a turbulent boundary layer

1983 ◽  
Vol 126 ◽  
pp. 147-165 ◽  
Author(s):  
Hiroshi Sakamoto ◽  
Mikio Arie
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Circular Cylinder ◽  
Turbulent Boundary Layer ◽  
Vortex Shedding ◽  
Rectangular Prism ◽  
Stream Velocity ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Two Bodies

Measurements of the vortex-shedding frequency behind a vertical rectangular prism and a vertical circular cylinder attached to a plane wall are correlated with the characteristics of the smooth-wall turbulent boundary layer in which they are immersed. Experimental data were collected to investigate the effects of (i) the aspect ratio of these bodies and (ii) the boundary-layer characteristics on the vortex-shedding frequency. The Strouhal number for the rectangular prism and the circular cylinder, defined by S = fcw/U0 and fcd/U0 respectively, was found to be expressed by a power function of the aspect ratio h/w (or h/d). Here fc is the vortex-shedding frequency, U0 is the free-stream velocity, h is the height, w is the width and d is the diameter. As the aspect ratio is reduced, the type of vortex shedding behind each of the two bodies was found to change from the Karman-type vortex to the arch-type vortex at the aspect ratio of 2·0 for the rectangular prism and 2·5 for the circular cylinder.

An Experimental Study of the Flow Above the Free Ends of Surface-Mounted Bluff Bodies

2012 ◽  
Author(s):  
Noorallah Rostamy ◽  
David Sumner ◽  
Donald J. Bergstrom ◽  
James D. Bugg
Keyword(s):  
Boundary Layer ◽  
Flow Pattern ◽  
Vortex Shedding ◽  
Ground Plane ◽  
Separated Flow ◽  
The Body ◽  
Bluff Bodies ◽  
Near Wake ◽  
Square Prism ◽  
Karman Vortex

The flow around surface-mounted finite-height bluff bodies is more complex than the flow around a two-dimensional or “infinite” cylinder. The flow over the free end and the boundary layer flow around the body-wall junction strongly influence the near-wake flow pattern. Streamwise tip vortex structures interact in a complex manner with Kármán vortex shedding from the sides of the body, and are responsible for a downward-directed local velocity field in the upper part of the wake known as “downwash.” A second pair of streamwise vortex structures, known as the base vortices, is found close to the ground plane. Upstream of the body the familiar horseshoe vortex is found. The interactions between the tip vortices, base vortices, and Kármán vortex shedding are strongly influenced by the aspect ratio, AR = H/D (for height, H, and width, D), the Reynolds number, Re, and the relative thickness of the boundary layer, δ/D. The flow above the free ends of surface-mounted finite-height circular cylinders and square prisms was studied in a low-speed wind tunnel using particle image velocimetry (PIV). Cylinders and prisms of AR = 9, 7, 5, and 3 were tested at Re = 4.2 × 104. The bodies were mounted normal to a ground plane and were partially immersed in a turbulent flat-plate boundary layer with δ/D = 1.7. PIV measurements were made above the free ends in three vertical planes at different cross-stream locations (y/D = 0, 0.25, and 0.375). The ensemble-averaged streamlines, turbulence intensity and Reynolds shear stress fields were obtained in these planes. The PIV results provide insight into the separated flow above the free ends, including the effects of AR and body shape. For the finite square prism, the large, separated, recirculating flow region extends into the near-wake. For the finite circular cylinder, this region is smaller and the separated flow reattaches onto the free-end surface. For the square prism of AR = 3, considerable difference is seen in the free-end flow pattern compared to the more slender prisms of AR = 9, 7 and 5. In particular, a cross-stream vortex is formed due to interaction between the separated flow from the leading edge of the prism and the reverse flow over the free end. This vortex is seen in all three planes for AR = 3 but only in the symmetry plane for AR = 9, while for the finite circular cylinder the flow pattern above the free end seems to be the same in all three planes for all aspect ratios, consisting of a cross-stream vortex at approximately x/D = 0.

scholarly journals Cavitation in Ka´rma´n Vortex Shedding From 2D Hydrofoil: Wall Roughness Effects

2007 ◽  
Author(s):  
Philippe Ausoni ◽  
Mohamed Farhat ◽  
Franc¸ois Avellan
Keyword(s):  
Boundary Layer ◽  
Vortex Shedding ◽  
Leading Edge ◽  
Transition To Turbulence ◽  
Special Focus ◽  
Roughness Effects ◽  
Vortex Induced Vibration ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Layer Flow

The present study deals with the shedding process of the Ka´rma´n vortices in the wake of a NACA0009 hydrofoil at high Reynolds number, Reh = 25·103 − 65·103. This research addresses the effects of the foil leading edge roughness on the wake dynamic with a special focus on the vortex shedding frequency, vortex-induced vibration and three-dimensionality of vortex shedding. For smooth leading edge, the shedding frequency of Ka´rma´n vortices occurs at constant Strouhal number, St = 0.24. The wake exhibits 3D instabilities and the vortex induced vibration signals strong modulation with intermittent weak shedding cycles. Direct relation between vibration amplitude and vortex spanwise organization is shown. In the case of rough leading edge, the Ka´rma´n shedding frequency is notably decreased compared to the smooth one, St = 0.18. Moreover, the vortex induced vibration level is significantly increased and the vibration spectra sharply peaked. The occurrence of vortex dislocations is shown to be less frequent with the roughness. The shedding of the vortices is considered on the whole as in phase along the hydrofoil span. Obviously, the shedding process of the Ka´rma´n vortices is highly related to the state of the boundary layer over the entire hydrofoil. It is believed that in the case of smooth leading edge, slight spanwise non-uniformities in the boundary-layer flow lead to slight instantaneous variation in vortex shedding frequency along the span which is enough to trigger vortex dislocations. On the contrary, for the rough leading edge, the location of transition to turbulence is uniformly forced which leads to the reduction of the spanwise boundary-layer non-uniformities and therefore to the enhancement of the coherence length of the Ka´rma´n vortices.

Sign in / Sign up

Export Citation Format

Share Document