A study of mixed-mode composite delamination using enriched interface elements

2013 ◽  
Vol 117 (1195) ◽  
pp. 959-967
Author(s):  
I. Guiamatsia ◽  
J. K. Ankersen ◽  
L. Iannucci
Keyword(s):  
Finite Elements ◽  
Analytical Solution ◽  
Elastic Foundation ◽  
Displacement Field ◽  
Mixed Mode ◽  
Crack Tip ◽  
Shape Functions ◽  
Interface Elements ◽  
Minimum Element ◽  
Element Size

Abstract This paper examines the performance of enriching the shape functions of interface finite elements in the prediction of mixed-mode delamination. Enriching second-order interface and solid elements with the analytical solution of a beam on elastic foundation problem yields the correct displacement field ahead of the crack tip. Despite the enrichment being fixed at elements nodes, resulting in non-traceability of the crack tip location, the strategy is shown to perform consistently well, increasing the minimum element size from the typical 0·5mm to 5mm, for a range of classical mixed-mode bending (MMB) specimens.

Thermal-Mechanical Fracture Analysis Considering Heat Flux Singularity

2019 ◽  
Vol 141 (12) ◽  
Author(s):  
Xiaofei Hu ◽  
Xing Ding ◽  
Yanguang Zhao ◽  
Weian Yao
Keyword(s):  
Heat Flux ◽  
Finite Element ◽  
Temperature Distribution ◽  
Analytical Solution ◽  
Thermal Conduction ◽  
Mixed Mode ◽  
Crack Tip ◽  
Fracture Analysis ◽  
Singular Element ◽  
Mechanical Fracture

Abstract Precise modeling of thermoelastic cracks remains challenging due to the fact that both heat flux and stress fields have singularity issue. In the previous studies, the first author proposed different types of symplectic analytical singular element (SASE) for thermal conduction and stress analysis of cracks. It has been demonstrated that these crack-tip elements of which the interior fields are defined by analytical solutions are highly accurate and efficient. However, the thermal mechanical coupling problem of crack cannot be treated with the existing SASEs. The main difficulty is that the analytical solution of the crack problem considering arbitrary temperature distribution is not available. Approximate solution may lead to significant numerical instabilities. Moreover, the construction of a crack-tip singular element for both thermal conduction and stress analysis is complicated and requires more efforts. In this study, the governing symplectic dual equation of thermoelastic crack is restudied. The analytical solution considering arbitrary temperature distribution is obtained in close form which, to the best of the authors' knowledge, has not been found before. Then, the finite element formulation of a new SASE for thermal-mechanical fracture analysis is derived analytically through a variational approach. A two-step analysis procedure is proposed to calculate the mixed mode thermal stress intensity factors (TSIFs)) and the analysis can be done on a fixed finite element mesh. Mesh refinement around the crack tip is unnecessary, and the mixed-mode TSIFs can be solved accurately without any postprocessing.

scholarly journals 3D-Based Transition hpq/hp-Adaptive Finite Elements for Analysis of Piezoelectrics

2021 ◽  
Vol 11 (9) ◽  
pp. 4062
Author(s):  
Grzegorz Zboiński ◽  
Magdalena Zielińska
Keyword(s):  
Finite Elements ◽  
Numerical Solutions ◽  
High Stress ◽  
Continuous Change ◽  
Transition Elements ◽  
Finite Element Approximations ◽  
Element Size ◽  
Piezoelectric Elements ◽  
Mechanical Models ◽  
Transition Models

This paper concerns the algorithm of transition piezoelectric elements for adaptive analysis of electro-mechanical systems. In addition, effectivity of the proposed elements in such an analysis is presented. The elements under consideration are assigned for joining basic elements which correspond to the mechanical models of either the first or higher order, while the electric model is of arbitrary order. In this work, three variants of the transition models are applied. The first one assures continuity of displacements between the basic models and continuity of electric potential between these models, as well. The second transition piezoelectric model guarantees additional continuity of the stress field between the basic models. The third transition model additionally enables continuous change of the strain state between the basic models. Based on the mentioned models, three types of the corresponding transition finite elements are introduced. The applied finite element approximations are hpq/hp-adaptive ones, which allows element-wise changes of the element size parameter h, and the element longitudinal and transverse orders of approximation, respectively, p and q, depending on the error level. Numerical effectiveness of the models and their approximations is investigated in the contexts of: ability to remove high stress gradients between the basic and transition models, and convergence of the numerical solutions for the model problems of piezoelectrics with and without the proposed transition elements.

scholarly journals Analytical corrections for double-cantilever beam tests

2021 ◽  
Author(s):  
T. Chen ◽  
C. M. Harvey ◽  
S. Wang ◽  
V. V. Silberschmidt
Keyword(s):  
Elastic Foundation ◽  
Analytical Solutions ◽  
Data Reduction ◽  
Crack Tip ◽  
Beam Theory ◽  
Dynamic Loads ◽  
Structural Vibration ◽  
Mode I ◽  
Mode I Fracture ◽  
Reduction Methods

AbstractDouble-cantilever beams (DCBs) are widely used to study mode-I fracture behavior and to measure mode-I fracture toughness under quasi-static loads. Recently, the authors have developed analytical solutions for DCBs under dynamic loads with consideration of structural vibration and wave propagation. There are two methods of beam-theory-based data reduction to determine the energy release rate: (i) using an effective built-in boundary condition at the crack tip, and (ii) employing an elastic foundation to model the uncracked interface of the DCB. In this letter, analytical corrections for a crack-tip rotation of DCBs under quasi-static and dynamic loads are presented, afforded by combining both these data-reduction methods and the authors’ recent analytical solutions for each. Convenient and easy-to-use analytical corrections for DCB tests are obtained, which avoid the complexity and difficulty of the elastic foundation approach, and the need for multiple experimental measurements of DCB compliance and crack length. The corrections are, to the best of the authors’ knowledge, completely new. Verification cases based on numerical simulation are presented to demonstrate the utility of the corrections.

Delamination of Laminate Plates

2014 ◽  
Vol 969 ◽  
pp. 97-100 ◽  
Author(s):  
Eva Kormaníková
Keyword(s):  
Finite Element Analysis ◽  
Mixed Mode ◽  
Plate Theory ◽  
Laminate Plate ◽  
Element Analysis ◽  
Interface Elements ◽  
First Order ◽  
Plate Elements ◽  
Interface Modeling ◽  
Shear Deformable

The paper deals with numerical modeling of delamination of laminate plate consists of unidirectional fiber reinforced layers. The methodology adopts the first-order shear laminate plate theory and fracture and contact mechanics. There are described sublaminate modeling and delamination modeling by the help of finite element analysis. With the interface modeling there is calculated the energy release rate along the lamination front. Numerical results are given for mixed mode delamination problems by implementing the method in a 2D finite analysis, which utilizes shear deformable plate elements and interface elements. Numerical example is done by the commercial ANSYS code.

Mismatch Effect on the Mixed Mode Type Creep Crack within Weldment

2016 ◽  
Vol 853 ◽  
pp. 281-285
Author(s):  
Jun Hui Zhang ◽  
Yan Wei Dai
Keyword(s):  
Mixed Mode ◽  
Stress Triaxiality ◽  
Crack Tip ◽  
Crack Tip Field ◽  
Creep Crack ◽  
Loading Mode ◽  
The Difference ◽  
Engineering Practices ◽  
Mismatch Effect ◽  
Transient And Steady State

Creep crack within weldments are very common in engineering practices, and the cracking location in these welding structures always appears at the HAZ location. The mismatch effect on the mixed mode creep crack is still not clear in these available literatures. The aim of this paper is to investigate the mismatch influence on the creep crack of mixed mode thoroughly. A mixed mode creep crack within HAZ is established in this paper. The leading factor that dominates the creep crack tip field under mixed loading mode is studied. The influences of mismatch effect on mode mixity, stress distribution and stress triaxiality are proposed. The difference of mixed mode creep crack and normal mode I or mode II creep crack are compared. The influence of mixity factor on the transient and steady state creep of crack tip are also analyzed.

Using the Multi-Parameter Fracture Mechanics for more Accurate Description of Stress/Displacement Crack Tip Fields

2013 ◽  
Vol 586 ◽  
pp. 237-240 ◽  
Author(s):  
Lucie Šestáková
Keyword(s):  
Stress Distribution ◽  
Fracture Mechanics ◽  
Boundary Conditions ◽  
Displacement Field ◽  
Singular Term ◽  
Crack Tip ◽  
Higher Order ◽  
Precise Description ◽  
Accurate Knowledge ◽  
Higher Order Terms

Most of fracture analyses often require an accurate knowledge of the stress/displacement field over the investigated body. However, this can be sometimes problematic when only one (singular) term of the Williams expansion is considered. Therefore, also other terms should be taken into account. Such an approach, referred to as multi-parameter fracture mechanics is used and investigated in this paper. Its importance for short/long cracks and the influence of different boundary conditions are studied. It has been found out that higher-order terms of the Williams expansion can contribute to more precise description of the stress distribution near the crack tip especially for long cracks. Unfortunately, the dependences obtained from the analyses presented are not unambiguous and it cannot be strictly derived how many of the higher-order terms are sufficient.

Atomistic Study of Cleavage and Dislocation Emission in NiAl

1994 ◽  
Vol 364 ◽  
Author(s):  
M. Ludwig ◽  
P. Gumbsch
Keyword(s):  
Finite Element ◽  
Mixed Mode ◽  
Crack Tip ◽  
Mode I ◽  
Crack Plane ◽  
Dislocation Emission ◽  
Dislocation Generation ◽  
Embedded Atom ◽  
Atomistic Study ◽  
Eam Potential

AbstractThe atomistic processes during fracture of NiAl are studied using a new embedded atom (EAM) potential to describe the region near the crack tip. To provide the atomistically modeled crack tip region with realistic boundary conditions, a coupled finite element - atomistic (FEAt) technique [1] is employed. In agreement with experimental observations, perfectly brittle cleavage is observed for the (110) crack plane. In contrast, cracks on the (100) plane either follow a zig-zag path on (110) planes, or emit dislocations. Dislocation generation is studied in more detail under mixed mode I/II loading conditions.

Shape functions and the accuracy of arch finite elements.

AIAA Journal ◽  
1973 ◽  
Vol 11 (3) ◽  
pp. 287-291 ◽  
Author(s):  
ISAAC FRIED
Keyword(s):  
Finite Elements ◽  
Shape Functions
Sign in / Sign up

Export Citation Format

Share Document