Vortex Shedding from Smooth and Roughened Cylinders in Cross-Flow near a Plane Surface

1979 ◽  
Vol 30 (1) ◽  
pp. 305-321 ◽  
Author(s):  
G. Buresti ◽  
A. Lanciotti
Keyword(s):  
Vortex Shedding ◽  
Plane Surface ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Cylinder Surface ◽  
Hot Wire ◽  
Cylinder Axis ◽  
Supercritical Regime ◽  
Subcritical Regime ◽  
Smooth Cylinder

SummaryThe characteristics of the flow field around a circular cylinder in cross-flow placed at various distances from a plane, parallel both to the flow and to the cylinder axis, were analysed using a hot wire anemometer. Experiments were performed in a wind tunnel with Reynolds numbers ranging from 0.85×105 to 3×105. The spectra of the hot wire signals were obtained using a Fast Fourier Transform technique programmed on a PDP 11/40 computer. As regards a smooth cylinder, the main features of the vortex shedding mechanism in the subcritical regime remained unaltered for distances from the plane greater than approximately 0.4 diameters; in particular the Strouhal frequency did not show any significant variation relative to the typical value for an isolated cylinder. As for lower values of the distance from the plane, the regular vortex shedding disappeared and the hot wire spectra showed typical turbulent features. The possibility of obtaining supercritical conditions by roughening the cylinder surface was confirmed together with the importance of the Reynolds number based on the typical roughness size, Rk, in the evaluation of the flow regime around the cylinder. In the case of roughened cylinders, and with values of Rk below-350, the regular vortex shedding disappeared at a distance from the plane smaller than 0.3 diameters. This fact suggests that, at least in part of the supercritical regime, the influence of the plane can be smaller than in the subcritical regime.

An experimental study of round jets in cross-flow

1996 ◽  
Vol 306 ◽  
pp. 111-144 ◽  
Author(s):  
R. M. Kelso ◽  
T. T. Lim ◽  
A. E. Perry
Keyword(s):  
Flow Visualization ◽  
Shear Layer ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Stream Velocity ◽  
Hot Wire ◽  
Vortex System ◽  
Freestream Velocity ◽  
Round Jets ◽  
Topological Features

The structure of round jets in cross-flow was studied using flow visualization techniques and flying-hot-wire measurements. The study was restricted to jet to freestream velocity ratios ranging from 2.0 to 6.0 and Reynolds numbers based on the jet diameter and free-stream velocity in the range of 440 to 6200.Flow visualization studies, together with time-averaged flying-hot-wire measurements in both vertical and horizontal sectional planes, have allowed the mean topological features of the jet in cross-flow to be identified using critical point theory. These features include the horseshoe (or necklace) vortex system originating just upstream of the jet, a separation region inside the pipe upstream of the pipe exit, the roll-up of the jet shear layer which initiates the counter-rotating vortex pair and the separation of the flat-wall boundary layer leading to the formation of the wake vortex system beneath the downstream side of the jet.The topology of the vortex ring roll-up of the jet shear layer was studied in detail using phase-averaged flying-hot-wire measurements of the velocity field when the roll-up was forced. From these data it is possible to examine the evolution of the shear layer topology. These results are supported by the flow visualization studies which also aid in their interpretation.The study also shows that, for velocity ratios ranging from 4.0 to 6.0, the unsteady upright vortices in the wake may form by different mechanisms, depending on the Reynolds number. It is found that at high Reynolds numbers, the upright vortex orientation in the wake may change intermittently from one configuration of vortex street to another. Three mechanisms are proposed to explain these observations.

Vortex Formation in the Wake of a Vibrating, Flexible Cable

1974 ◽  
Vol 96 (4) ◽  
pp. 317-322 ◽  
Author(s):  
S. E. Ramberg ◽  
O. M. Griffin
Keyword(s):  
Vortex Shedding ◽  
Vortex Formation ◽  
Reynolds Numbers ◽  
Hot Wire ◽  
Near Wake ◽  
Formation Region ◽  
Vortex Streets ◽  
Region Length ◽  
Karman Vortex ◽  
Flexible Cables

The von Karman vortex streets formed in the wakes of vibrating, flexible cables were studied using a hot-wire anemometer. All the experiments took place in the flow regime where the vibration and vortex-shedding frequencies lock together, or synchronize, to control the wake formation. Detailed measurements were made of the vortex formation flow for Reynolds numbers between 230 and 650. As in the case of vibrating cylinders, the formation-region length is dependent on a shedding parameter St* related to the natural Strouhal number and the vibrational conditions. Furthermore, the near wake configuration is found to be dependent on the local amplitude of vibration suggesting that the vibrating cylinder rseults are directly applicable in that region.

Direct Numerical Simulation of Flow and Heat Transfer From a Sphere in a Uniform Cross-Flow

2000 ◽  
Vol 123 (2) ◽  
pp. 347-358 ◽  
Author(s):  
P. Bagchi ◽  
M. Y. Ha ◽  
S. Balachandar
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Vortex Shedding ◽  
Axisymmetric Flow ◽  
Three Dimensional ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Temperature Fields ◽  
Flow And Heat Transfer

Direct numerical solution for flow and heat transfer past a sphere in a uniform flow is obtained using an accurate and efficient Fourier-Chebyshev spectral collocation method for Reynolds numbers up to 500. We investigate the flow and temperature fields over a range of Reynolds numbers, showing steady and axisymmetric flow when the Reynolds number is less than 210, steady and nonaxisymmetric flow without vortex shedding when the Reynolds number is between 210 and 270, and unsteady three-dimensional flow with vortex shedding when the Reynolds number is above 270. Results from three-dimensional simulation are compared with the corresponding axisymmetric simulations for Re>210 in order to see the effect of unsteadiness and three-dimensionality on heat transfer past a sphere. The local Nusselt number distribution obtained from the 3D simulation shows big differences in the wake region compared with axisymmetric one, when there exists strong vortex shedding in the wake. But the differences in surface-average Nusselt number between axisymmetric and three-dimensional simulations are small owing to the smaller surface area associated with the base region. The shedding process is observed to be dominantly one-sided and as a result axisymmetry of the surface heat transfer is broken even after a time-average. The one-sided shedding also results in a time-averaged mean lift force on the sphere.

Computational Determination of the Modified Vortex Shedding Frequency for a Rigid, Truncated, Wall-Mounted Cylinder in Cross Flow

2014 ◽  
Author(s):  
Aimie Faucett ◽  
Todd Harman ◽  
Tim Ameel
Keyword(s):  
Vortex Shedding ◽  
Cross Flow ◽  
Classical Case ◽  
Reynolds Numbers ◽  
Two Dimensional ◽  
End Effects ◽  
Dimensional Solution ◽  
Horseshoe Vortices ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

Flow around a rigid, truncated, wall-mounted cylinder with an aspect ratio of 5 is examined computationally at various Reynolds numbers Re to determine how the end effects impact the vortex shedding frequency. The existence of the wall and free end cause a dampening of the classical shedding frequency found for a semi-infinite, two-dimensional cylinder, as horseshoe vortices along the wall and flow over the tip entrain into the shedding region. This effect was observed for Reynolds numbers in the range of 50 to 2000, and quantified by comparing the modified Strouhal numbers to the classical (two-dimensional) solution for Strouhal number as a function of Reynolds number. The range of transition was found to be 220 < Re < 300, versus 150 < Re < 300 for the classical case. Vortex shedding started at Re ≈ 100, significantly above Re = 50, where shedding starts for the two-dimensional case.

Synchronized Vibrations of a Circular Cylinder in Cross Flow at Supercritical Reynolds Numbers1

2003 ◽  
Vol 125 (1) ◽  
pp. 97-108 ◽  
Author(s):  
Tsutomu Kawamura ◽  
Toshitsugu Nakao ◽  
Masanori Takahashi ◽  
Masaaki Hayashi ◽  
Kouichi Murayama ◽  
...  
Keyword(s):  
Circular Cylinder ◽  
Strouhal Number ◽  
Vortex Shedding ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Excited Vibration ◽  
Karman Vortex ◽  
Lock In

Synchronized vibrations of a circular cylinder in a water cross flow at supercritical Reynolds numbers were measured. Turbulence intensities were varied to investigate the effect of the Strouhal number on the synchronization range. Self-excited vibration in the drag direction due to symmetrical vortex shedding began only when the Strouhal number was about 0.29, at a reduced velocity of 1.1. The reduced velocities at the beginning of lock-in vibrations caused by Karman vortex shedding decreased from 1.5 to 1.1 in the drag direction and from 2.7 to 2.2 in the lift direction, as the Strouhal number increased from 0.29 to 0.48.

Laminar Forced Convection for Flow Across a Cylinder With Longitudinal Fins of Finite Thickness

2008 ◽  
Vol 130 (9) ◽  
Author(s):  
S. C. Haldar ◽  
G. S. Kochhar ◽  
K. Manohar
Keyword(s):  
Heat Transfer ◽  
Forced Convection ◽  
Finite Thickness ◽  
Cross Flow ◽  
Cylinder Surface ◽  
Total Heat Transfer ◽  
Smooth Cylinder ◽  
Opposing Effects ◽  
Laminar Forced Convection ◽  
Free Area

Conjugate numerical solution of laminar forced convection for cross-flow over a cylinder with external longitudinal fins of finite thickness has been carried out. The rate of heat transfer from the fins increases and that from the free area of the cylinder marginally decreases with an increase in thickness, length, and number of fins. The rate of heat transfer from the fins alone is usually much higher than that from the cylinder surface. As a consequence, the net result of these two opposing effects is an increase in the total heat transfer over that of the smooth cylinder, the amount increasing with an increase in thickness, length, and number of fins but with diminishing returns. The fins are more effective at high Re values than at low ones.

Influence of Thermal Buoyancy on Vortex Shedding Behind a Rotating Circular Cylinder in Cross Flow at Subcritical Reynolds Numbers

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Dipankar Chatterjee ◽  
Chiranjit Sinha
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Thermal Instability ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Forced Flow ◽  
Thermal Buoyancy ◽  
Thermal Fields ◽  
Rotating Circular Cylinder ◽  
Unbounded Medium

The vortex shedding (VS) behind stationary bluff obstacles in cross-flow can be initiated by imposing thermal instability at subcritical Reynolds numbers (Re). We demonstrate here that additional thermal instability is required to be imparted in the form of heating for destabilizing the flow around a rotating bluff obstacle. A two-dimensional numerical simulation is performed in this regard to investigate the influences of cross buoyancy on the VS process behind a heated and rotating circular cylinder at subcritical Re. The flow is considered in an unbounded medium. The range of Re is chosen to be 5–45 with a dimensionless rotational speed (Ω) ranging between 0 and 4. At this subcritical range of Reynolds number the flow and thermal fields are found to be steady without the superimposed thermal buoyancy (i.e., for pure forced flow). However, as the buoyancy parameter (Richardson number, Ri) increases flow becomes unstable and subsequently, at some critical value of Ri, periodic VS is observed to characterize the flow and thermal fields. The rotation of the cylinder is found to have a stabilizing effect and as Ω increases more heating is observed to be required to destabilize the flow.

Vortex shedding from a cylinder vibrating in line with an incident uniform flow

1976 ◽  
Vol 75 (2) ◽  
pp. 257-271 ◽  
Author(s):  
Owen M. Griffin ◽  
Steven E. Ramberg
Keyword(s):  
Vortex Shedding ◽  
Vibration Amplitude ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Vortex Wake ◽  
Single Vortex ◽  
Vortex Pairs ◽  
Wake Patterns ◽  
Shedding Frequency ◽  
Basic Characteristics

A study has been made of the wake of a cylinder vibrating in line with an incident steady flow. The Reynolds number for the experiments was 190, and the vortex shedding was at all times synchronized with the vibrations of the cylinder, which were in a range of frequencies near twice the Strouhal shedding frequency for the stationary cylinder. Two distinct vortex wake patterns were encountered. The first is a complex regime in which two vortices are shed during each cycle of the vibration and form an alternating pattern of vortex pairs downstream. The second pattern is an alternating street which results from the shedding of a single vortex during each cycle of the cylinder's motion. The street geometry in the latter case shares many basic characteristics with the wake of a cylinder vibrating in cross-flow. These include the effects of vibration amplitude and frequency on the longitudinal and transverse spacing of the vortices. The results obtained from these experiments in air are in agreement with previous findings from free- and forced-vibration experiments in water at both higher and lower Reynolds numbers.

Experimental evidence of new three-dimensional modes in the wake of a rotating cylinder

2013 ◽  
Vol 734 ◽  
pp. 567-594 ◽  
Author(s):  
A. Radi ◽  
M. C. Thompson ◽  
A. Rao ◽  
K. Hourigan ◽  
J. Sheridan
Keyword(s):  
Rotation Rate ◽  
Numerical Study ◽  
Water Channel ◽  
Three Dimensional ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Rotating Cylinder ◽  
Travelling Wave ◽  
Cylinder Surface ◽  
Rotation Rates

AbstractA recent numerical study by Rao et al. (J. Fluid Mech., vol. 717, 2013, pp. 1–29) predicted the existence of several previously unobserved linearly unstable three-dimensional modes in the wake of a spinning cylinder in cross-flow. While linear stability analysis suggests that some of these modes exist for relatively limited ranges of Reynolds numbers and rotation rates, this may not be true for fully developed nonlinear wakes. In the current paper, we present the results of water channel experiments on a rotating cylinder in cross-flow, for Reynolds numbers $200\leqslant \mathit{Re}\leqslant 275$ and non-dimensional rotation rates $0\leqslant \alpha \leqslant 2. 5$. Using particle image velocimetry and digitally post-processed hydrogen bubble flow visualizations, we confirm the existence of the predicted modes for the first time experimentally. For instance, for $\mathit{Re}= 275$ and a rotation rate of $\alpha = 1. 7$, we observe a subharmonic mode, mode C, with a spanwise wavelength of ${\lambda }_{z} / d\approx 1. 1$. On increasing the rotation rate, two modes with a wavelength of ${\lambda }_{z} / d\approx 2$ become unstable in rapid succession, termed modes D and E. Mode D grows on a shedding wake, whereas mode E consists of streamwise vortices on an otherwise steady wake. For $\alpha \gt 2. 2$, a short-wavelength mode F appears localized close to the cylinder surface with ${\lambda }_{z} / d\approx 0. 5$, which is presumably a manifestation of centrifugal instability. Unlike the other modes, mode F is a travelling wave with a spanwise frequency of ${\mathit{St}}_{3D} \approx 0. 1$. In addition to these new modes, observations on the one-sided shedding process, known as the ‘second shedding’, are reported for $\alpha = 5. 1$. Despite suggestions from the literature, this process seems to be intrinsically three-dimensional. In summary, our experiments confirm the linear predictions by Rao et al., with very good agreement of wavelengths, symmetries and the phase velocity for the travelling mode. Apart from this, these experiments examine the nonlinear saturated state of these modes and explore how the existence of multiple unstable modes can affect the selected final state. Finally, our results establish that several distinct three-dimensional instabilities exist in a relatively confined area on the $\mathit{Re}$–$\alpha $ parameter map, which could account for their non-detection previously.

Sign in / Sign up

Export Citation Format

Share Document