Vortex shedding from a cylinder vibrating in line with an incident uniform flow

1976 ◽  
Vol 75 (2) ◽  
pp. 257-271 ◽  
Author(s):  
Owen M. Griffin ◽  
Steven E. Ramberg
Keyword(s):  
Vortex Shedding ◽  
Vibration Amplitude ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Vortex Wake ◽  
Single Vortex ◽  
Vortex Pairs ◽  
Wake Patterns ◽  
Shedding Frequency ◽  
Basic Characteristics

A study has been made of the wake of a cylinder vibrating in line with an incident steady flow. The Reynolds number for the experiments was 190, and the vortex shedding was at all times synchronized with the vibrations of the cylinder, which were in a range of frequencies near twice the Strouhal shedding frequency for the stationary cylinder. Two distinct vortex wake patterns were encountered. The first is a complex regime in which two vortices are shed during each cycle of the vibration and form an alternating pattern of vortex pairs downstream. The second pattern is an alternating street which results from the shedding of a single vortex during each cycle of the cylinder's motion. The street geometry in the latter case shares many basic characteristics with the wake of a cylinder vibrating in cross-flow. These include the effects of vibration amplitude and frequency on the longitudinal and transverse spacing of the vortices. The results obtained from these experiments in air are in agreement with previous findings from free- and forced-vibration experiments in water at both higher and lower Reynolds numbers.

Computational Determination of the Modified Vortex Shedding Frequency for a Rigid, Truncated, Wall-Mounted Cylinder in Cross Flow

2014 ◽  
Author(s):  
Aimie Faucett ◽  
Todd Harman ◽  
Tim Ameel
Keyword(s):  
Vortex Shedding ◽  
Cross Flow ◽  
Classical Case ◽  
Reynolds Numbers ◽  
Two Dimensional ◽  
End Effects ◽  
Dimensional Solution ◽  
Horseshoe Vortices ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

Flow around a rigid, truncated, wall-mounted cylinder with an aspect ratio of 5 is examined computationally at various Reynolds numbers Re to determine how the end effects impact the vortex shedding frequency. The existence of the wall and free end cause a dampening of the classical shedding frequency found for a semi-infinite, two-dimensional cylinder, as horseshoe vortices along the wall and flow over the tip entrain into the shedding region. This effect was observed for Reynolds numbers in the range of 50 to 2000, and quantified by comparing the modified Strouhal numbers to the classical (two-dimensional) solution for Strouhal number as a function of Reynolds number. The range of transition was found to be 220 < Re < 300, versus 150 < Re < 300 for the classical case. Vortex shedding started at Re ≈ 100, significantly above Re = 50, where shedding starts for the two-dimensional case.

scholarly journals FLOW AROUND MODIFIED CIRCULAR CILYNDERS

2004 ◽  
Vol 3 (1) ◽  
pp. 62
Author(s):  
R. L. Ferreira ◽  
E. D. R. Vieira
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Reynolds Numbers ◽  
Vortex Wake ◽  
Continuous Mode ◽  
Longitudinal Slit ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Hot Film ◽  
The Relationship

The flow around a circular cylinder has awaken the attention of different researchers since the historic Strouhal's work of 1878. Ever since, many experimental and numeric works have been carried out in order to determine the relationship between the vortex shedding frequency and the flow regime. Recently, a number of studies have been developed using several small modifications in circular cylinder. In this work a circular cylinder modified with a longitudinal concave notch, has been tested in order to determine the relationship between the non-dimensional vortex shedding frequency (Strouhal number) and the Reynolds number has been determined to Reynolds up to 600. Additionally a modified circular cylinder with a longitudinal slit also has been tested in order to determine the Strouhal-Reynolds relationship in several attack angle configurations. The experiments have been carried out in a vertical low turbulence hydrodynamic tunnel with 146x146x500 mm of test section operating in continuous mode. Flow visualization by direct liquid dye injection has been utilized in order to produce vortex images. These images have been captured in still chemical photography for different Reynolds numbers. A hot-film probe has been adequately positioned in the vortex wake to determine the vortex shedding frequency and consequently the Strouhal number.

An Experimental Study on the Vertical Flow Past a Finite-Length Horizontal Cylinder at Low Reynolds Numbers

2014 ◽  
Vol 493 ◽  
pp. 68-73 ◽  
Author(s):  
Willy Stevanus ◽  
Yi Jiun Peter Lin
Keyword(s):  
Finite Length ◽  
Vortex Shedding ◽  
Vortex Formation ◽  
Reynolds Numbers ◽  
Horizontal Cylinder ◽  
Vortex Street ◽  
Vertical Flow ◽  
Low Reynolds Numbers ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency

The research studies the characteristics of the vertical flow past a finite-length horizontal cylinder at low Reynolds numbers (ReD) from 250 to 1080. The experiments were performed in a vertical closed-loop water tunnel. Flow fields were observed by the particle tracer approach for flow visualization and measured by the Particle Image Velocimetry (P.I.V.) approach for velocity fields. The characteristics of vortex formation in the wake of the finite-length cylinder change at different regions from the tip to the base of it. Near the tip, a pair of vortices in the wake was observed and the size of the vortex increased as the observed section was away from the tip. Around a distance of 3 diameters of the cylinder from its tip, the vortex street in the wake was observed. The characteristics of vortex formation also change with increasing Reynolds numbers. At X/D = -3, a pair of vortices was observed in the wake for ReD = 250, but as the ReD increases the vortex street was observed at the same section. The vortex shedding frequency is analyzed by Fast Fourier Transform (FFT). Experimental results show that the downwash flow affects the vortex shedding frequency even to 5 diameters of the cylinder from its tip. The interaction between the downwash flow and the Von Kármán vortex street in the wake of the cylinder is presented in this paper.

Vortex Shedding from Smooth and Roughened Cylinders in Cross-Flow near a Plane Surface

1979 ◽  
Vol 30 (1) ◽  
pp. 305-321 ◽  
Author(s):  
G. Buresti ◽  
A. Lanciotti
Keyword(s):  
Vortex Shedding ◽  
Plane Surface ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Cylinder Surface ◽  
Hot Wire ◽  
Cylinder Axis ◽  
Supercritical Regime ◽  
Subcritical Regime ◽  
Smooth Cylinder

SummaryThe characteristics of the flow field around a circular cylinder in cross-flow placed at various distances from a plane, parallel both to the flow and to the cylinder axis, were analysed using a hot wire anemometer. Experiments were performed in a wind tunnel with Reynolds numbers ranging from 0.85×105 to 3×105. The spectra of the hot wire signals were obtained using a Fast Fourier Transform technique programmed on a PDP 11/40 computer. As regards a smooth cylinder, the main features of the vortex shedding mechanism in the subcritical regime remained unaltered for distances from the plane greater than approximately 0.4 diameters; in particular the Strouhal frequency did not show any significant variation relative to the typical value for an isolated cylinder. As for lower values of the distance from the plane, the regular vortex shedding disappeared and the hot wire spectra showed typical turbulent features. The possibility of obtaining supercritical conditions by roughening the cylinder surface was confirmed together with the importance of the Reynolds number based on the typical roughness size, Rk, in the evaluation of the flow regime around the cylinder. In the case of roughened cylinders, and with values of Rk below-350, the regular vortex shedding disappeared at a distance from the plane smaller than 0.3 diameters. This fact suggests that, at least in part of the supercritical regime, the influence of the plane can be smaller than in the subcritical regime.

Direct Numerical Simulation of Flow and Heat Transfer From a Sphere in a Uniform Cross-Flow

2000 ◽  
Vol 123 (2) ◽  
pp. 347-358 ◽  
Author(s):  
P. Bagchi ◽  
M. Y. Ha ◽  
S. Balachandar
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Vortex Shedding ◽  
Axisymmetric Flow ◽  
Three Dimensional ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Temperature Fields ◽  
Flow And Heat Transfer

Direct numerical solution for flow and heat transfer past a sphere in a uniform flow is obtained using an accurate and efficient Fourier-Chebyshev spectral collocation method for Reynolds numbers up to 500. We investigate the flow and temperature fields over a range of Reynolds numbers, showing steady and axisymmetric flow when the Reynolds number is less than 210, steady and nonaxisymmetric flow without vortex shedding when the Reynolds number is between 210 and 270, and unsteady three-dimensional flow with vortex shedding when the Reynolds number is above 270. Results from three-dimensional simulation are compared with the corresponding axisymmetric simulations for Re>210 in order to see the effect of unsteadiness and three-dimensionality on heat transfer past a sphere. The local Nusselt number distribution obtained from the 3D simulation shows big differences in the wake region compared with axisymmetric one, when there exists strong vortex shedding in the wake. But the differences in surface-average Nusselt number between axisymmetric and three-dimensional simulations are small owing to the smaller surface area associated with the base region. The shedding process is observed to be dominantly one-sided and as a result axisymmetry of the surface heat transfer is broken even after a time-average. The one-sided shedding also results in a time-averaged mean lift force on the sphere.

Synchronized Vibrations of a Circular Cylinder in Cross Flow at Supercritical Reynolds Numbers1

2003 ◽  
Vol 125 (1) ◽  
pp. 97-108 ◽  
Author(s):  
Tsutomu Kawamura ◽  
Toshitsugu Nakao ◽  
Masanori Takahashi ◽  
Masaaki Hayashi ◽  
Kouichi Murayama ◽  
...  
Keyword(s):  
Circular Cylinder ◽  
Strouhal Number ◽  
Vortex Shedding ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Excited Vibration ◽  
Karman Vortex ◽  
Lock In

Synchronized vibrations of a circular cylinder in a water cross flow at supercritical Reynolds numbers were measured. Turbulence intensities were varied to investigate the effect of the Strouhal number on the synchronization range. Self-excited vibration in the drag direction due to symmetrical vortex shedding began only when the Strouhal number was about 0.29, at a reduced velocity of 1.1. The reduced velocities at the beginning of lock-in vibrations caused by Karman vortex shedding decreased from 1.5 to 1.1 in the drag direction and from 2.7 to 2.2 in the lift direction, as the Strouhal number increased from 0.29 to 0.48.

Influence of Thermal Buoyancy on Vortex Shedding Behind a Rotating Circular Cylinder in Cross Flow at Subcritical Reynolds Numbers

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Dipankar Chatterjee ◽  
Chiranjit Sinha
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Thermal Instability ◽  
Cross Flow ◽  
Reynolds Numbers ◽  
Forced Flow ◽  
Thermal Buoyancy ◽  
Thermal Fields ◽  
Rotating Circular Cylinder ◽  
Unbounded Medium

The vortex shedding (VS) behind stationary bluff obstacles in cross-flow can be initiated by imposing thermal instability at subcritical Reynolds numbers (Re). We demonstrate here that additional thermal instability is required to be imparted in the form of heating for destabilizing the flow around a rotating bluff obstacle. A two-dimensional numerical simulation is performed in this regard to investigate the influences of cross buoyancy on the VS process behind a heated and rotating circular cylinder at subcritical Re. The flow is considered in an unbounded medium. The range of Re is chosen to be 5–45 with a dimensionless rotational speed (Ω) ranging between 0 and 4. At this subcritical range of Reynolds number the flow and thermal fields are found to be steady without the superimposed thermal buoyancy (i.e., for pure forced flow). However, as the buoyancy parameter (Richardson number, Ri) increases flow becomes unstable and subsequently, at some critical value of Ri, periodic VS is observed to characterize the flow and thermal fields. The rotation of the cylinder is found to have a stabilizing effect and as Ω increases more heating is observed to be required to destabilize the flow.

A Study on Vortex Shedding From Spheres in a Uniform Flow

1990 ◽  
Vol 112 (4) ◽  
pp. 386-392 ◽  
Author(s):  
H. Sakamoto ◽  
H. Haniu
Keyword(s):  
Reynolds Number ◽  
Strouhal Number ◽  
Vortex Shedding ◽  
Water Channel ◽  
Reynolds Numbers ◽  
Uniform Flow ◽  
Freestream Velocity ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Visualization Experiments

Vortex shedding from spheres at Reynolds numbers from 3 × 102 to 4 × 104 in a uniform flow was investigated experimentally. Standard hot-wire technique were used to measure the vortex shedding frequency from spheres in a low-speed wind tunnel. Flow-visualization experiments were carried out in a water channel. Important results from the investigation were that (i) the variation of the Strouhal number St (=fD/U0, U0: freestream velocity, D: diameter of the sphere, f: vortex shedding frequency) with the Reynolds number (= U0D/v, v: kinematic viscosity) can be classified into four regions, (ii) the Reynolds number at which the hairpinshaped vortices begin to change from laminar to turbulent vortices so that the wake structure behind the sphere is not shown clearly when a Reynolds number of about 800 is reached, and (vi) at Reynolds numbers ranging from 8X102 to 1.5X104, the higher and lower frequency modes of the Strouhal number coexist.

Sign in / Sign up

Export Citation Format

Share Document