scholarly journals A study of the flow-field evolution and mixing in a planar turbulent jet using direct numerical simulation

2002 ◽  
Vol 450 ◽  
pp. 377-407 ◽  
Author(s):  
S. A. STANLEY ◽  
S. SARKAR ◽  
J. P. MELLADO
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Direct Numerical Simulation ◽  
Large Scale ◽  
Computational Study ◽  
Practical Interest ◽  
Small Scale ◽  
Mixing Process ◽  
Mean Velocity ◽  
Small Scales

Turbulent plane jets are prototypical free shear flows of practical interest in propulsion, combustion and environmental flows. While considerable experimental research has been performed on planar jets, very few computational studies exist. To the authors' knowledge, this is the first computational study of spatially evolving three-dimensional planar turbulent jets utilizing direct numerical simulation. Jet growth rates as well as the mean velocity, mean scalar and Reynolds stress profiles compare well with experimental data. Coherency spectra, vorticity visualization and autospectra are obtained to identify inferred structures. The development of the initial shear layer instability, as well as the evolution into the jet column mode downstream is captured well.The large- and small-scale anisotropies in the jet are discussed in detail. It is shown that, while the large scales in the flow field adjust slowly to variations in the local mean velocity gradients, the small scales adjust rapidly. Near the centreline of the jet, the small scales of turbulence are more isotropic. The mixing process is studied through analysis of the probability density functions of a passive scalar. Immediately after the rollup of vortical structures in the shear layers, the mixing process is dominated by large-scale engulfing of fluid. However, small-scale mixing dominates further downstream in the turbulent core of the self-similar region of the jet and a change from non-marching to marching PDFs is observed. Near the jet edges, the effects of large-scale engulfing of coflow fluid continue to influence the PDFs and non-marching type behaviour is observed.

scholarly journals Anisotropic Characteristics of Turbulence Dissipation in Swirling Flow: A Direct Numerical Simulation Study

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Xingtuan Yang ◽  
Nan Gui ◽  
Gongnan Xie ◽  
Jie Yan ◽  
Jiyuan Tu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Energy Dissipation ◽  
Direct Numerical Simulation ◽  
Large Scale ◽  
Isotropic Turbulence ◽  
Vortex Breakdown ◽  
Swirling Flow ◽  
Turbulent Energy ◽  
Swirling Flows ◽  
Small Scale

This study investigates the anisotropic characteristics of turbulent energy dissipation rate in a rotating jet flow via direct numerical simulation. The turbulent energy dissipation tensor, including its eigenvalues in the swirling flows with different rotating velocities, is analyzed to investigate the anisotropic characteristics of turbulence and dissipation. In addition, the probability density function of the eigenvalues of turbulence dissipation tensor is presented. The isotropic subrange of PDF always exists in swirling flows relevant to small-scale vortex structure. Thus, with remarkable large-scale vortex breakdown, the isotropic subrange of PDF is reduced in strongly swirling flows, and anisotropic energy dissipation is proven to exist in the core region of the vortex breakdown. More specifically, strong anisotropic turbulence dissipation occurs concentratively in the vortex breakdown region, whereas nearly isotropic turbulence dissipation occurs dispersively in the peripheral region of the strong swirling flows.

Direct Numerical Simulation of Pulsating Jet Mixing

2007 ◽  
Author(s):  
Sangsig Yun ◽  
Joan Boulanger ◽  
Leiyong Jiang
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Direct Numerical Simulation ◽  
Heat Release ◽  
Favorable Effect ◽  
Flow Structures ◽  
Modulation Amplitude ◽  
Mixing Process ◽  
Jet Mixing ◽  
Pulsating Jet

In lean premixed combustors, the fuel/air ratio oscillation can cause a serious problem since it can produce pressure and heat release fluctuations, and further, combustion instability if it is well phased with them. In order to design a system where such air/fuel ratio fluctuation is well suppressed, it is important to understand the mixing process and its interaction with the flow structures inside a premixer. In this study, the flow-field of a pulsating jet and the mixing of the jet with the co-flow are examined using direct numerical simulation. The effects of the frequency and amplitude of the imposed pulsation on the flow structures and mixing process are investigated in detail. It is found that the modulation amplitude has a favorable effect on mixing, but the dependency on frequency is more complicated.

scholarly journals Numerical simulation of leakage flow field and acoustic characteristics for safety valve

2021 ◽  
Vol 336 ◽  
pp. 01007
Author(s):  
Fan Qian ◽  
Minghui Hu
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Pressure Fluctuation ◽  
Large Scale ◽  
Safety Valve ◽  
Sound Field ◽  
Wall Pressure ◽  
Small Scale ◽  
Acoustic Analogy ◽  
Wall Pressure Fluctuation

Aiming at the internal leakage problem of spring type nuclear safety valve at the sealing surface, the flow field and sound field characteristics at the leakage height of 0.5mm between the valve disc and the valve seat sealing surface were studied, and the numerical simulation was carried out based on large eddy simulation(LES) and mohring acoustic analogy method, and compare the effects of acoustic wall pressure fluctuation(AWPF) and turbulent wall pressure fluctuation(TWPF) as the excitation source on the external sound field of the valve. The simulation results show that: the change gradient of velocity field and pressure field at the leakage port of safety valve is significant and form vortices of different sizes. The small-scale vortices are mainly in the leakage port, while the large-scale vortices mainly exist in the flow channel; When the valve is leaking, the noise is mainly dominated by high-pressure injection noise, its spectrum curve shows wide-band characteristics, and the external noise of the valve is mainly caused by AW P F. The above research results can provide a theoretical basis for the safety valve online detection method.

The correspondence between drag enhancement and vortical structures in turbulent Taylor–Couette flows with polymer additives: a study of curvature dependence

2019 ◽  
Vol 881 ◽  
pp. 602-616 ◽  
Author(s):  
Jiaxing Song ◽  
Hao Teng ◽  
Nansheng Liu ◽  
Hang Ding ◽  
Xi-Yun Lu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Angular Momentum ◽  
Direct Numerical Simulation ◽  
Large Scale ◽  
Underlying Mechanism ◽  
Vortical Flow ◽  
Small Scale ◽  
Vortical Structures ◽  
Taylor Couette ◽  
Curvature Dependence

We report direct numerical simulation results that clearly elucidate the mechanism that leads to curvature dependence of drag enhancement (DE) in viscoelastic turbulent Taylor–Couette flow. Change in the angular momentum transport and its inherent link to transitions in vortical flow structures have been explored to depict the influence of the curvature of the flow geometry on DE. Specifically, it has been demonstrated that a transition in vortical structures with increasing radius ratio leads to weakening and elimination of the small-scale Görtler vortices and development and better organization (occupying the entire gap) of large-scale Taylor vortices as also evinced by the patterns of angular momentum current. The commensurate change in DE and its underlying mechanism are examined by contributions of convective flux and polymeric stress to the angular momentum current. The present finding paves the way for capturing highly localized elastic turbulence structures in direct numerical simulation by increasing geometry curvature in traditional turbulent curvilinear flows.

Direct numerical simulation of a turbulent jet impinging on a heated wall

2015 ◽  
Vol 764 ◽  
pp. 362-394 ◽  
Author(s):  
T. Dairay ◽  
V. Fortuné ◽  
E. Lamballais ◽  
L.-E. Brizzi
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Nusselt Number ◽  
Direct Numerical Simulation ◽  
Temperature Fields ◽  
Heated Wall ◽  
Small Scale ◽  
Turbulent Regime ◽  
High Heat Transfer ◽  
Radial Evolution

AbstractDirect numerical simulation (DNS) of an impinging jet flow with a nozzle-to-plate distance of two jet diameters and a Reynolds number of 10 000 is carried out at high spatial resolution using high-order numerical methods. The flow configuration is designed to enable the development of a fully turbulent regime with the appearance of a well-marked secondary maximum in the radial distribution of the mean heat transfer. The velocity and temperature statistics are validated with documented experiments. The DNS database is then analysed focusing on the role of unsteady processes to explain the spatial distribution of the heat transfer coefficient at the wall. A phenomenological scenario is proposed on the basis of instantaneous flow visualisations in order to explain the non-monotonic radial evolution of the Nusselt number in the stagnation region. This scenario is then assessed by analysing the wall temperature and the wall shear stress distributions and also through the use of conditional averaging of velocity and temperature fields. On one hand, the heat transfer is primarily driven by the large-scale toroidal primary and secondary vortices emitted periodically. On the other hand, these vortices are subjected to azimuthal distortions associated with the production of radially elongated structures at small scale. These distortions are responsible for the appearance of very high heat transfer zones organised as cold fluid spots on the heated wall. These cold spots are shaped by the radial structures through a filament propagation of the heat transfer. The analysis of probability density functions shows that these strong events are highly intermittent in time and space while contributing essentially to the secondary peak observed in the radial evolution of the Nusselt number.

scholarly journals Flow topologies in bubble-induced turbulence: a direct numerical simulation analysis

2018 ◽  
Vol 857 ◽  
pp. 270-290 ◽  
Author(s):  
Josef Hasslberger ◽  
Markus Klein ◽  
Nilanjan Chakraborty
Keyword(s):  
Numerical Simulation ◽  
Direct Numerical Simulation ◽  
Turbulent Flows ◽  
Volume Fraction ◽  
Fluid Velocity ◽  
Small Scale ◽  
Flow Topology ◽  
Two Phase ◽  
Local Flow ◽  
Interface Curvature

This paper presents a detailed investigation of flow topologies in bubble-induced two-phase turbulence. Two freely moving and deforming air bubbles that have been suspended in liquid water under counterflow conditions have been considered for this analysis. The direct numerical simulation data considered here are based on the one-fluid formulation of the two-phase flow governing equations. To study the development of coherent structures, a local flow topology analysis is performed. Using the invariants of the velocity gradient tensor, all possible small-scale flow structures can be categorized into two nodal and two focal topologies for incompressible turbulent flows. The volume fraction of focal topologies in the gaseous phase is consistently higher than in the surrounding liquid phase. This observation has been argued to be linked to a strong vorticity production at the regions of simultaneous high fluid velocity and high interface curvature. Depending on the regime (steady/laminar or unsteady/turbulent), additional effects related to the density and viscosity jump at the interface influence the behaviour. The analysis also points to a specific term of the vorticity transport equation as being responsible for the induction of vortical motion at the interface. Besides the known mechanisms, this term, related to surface tension and gradients of interface curvature, represents another potential source of turbulence production that lends itself to further investigation.

Direct numerical simulation of turbulent channel flow up to

2015 ◽  
Vol 774 ◽  
pp. 395-415 ◽  
Author(s):  
Myoungkyu Lee ◽  
Robert D. Moser
Keyword(s):  
Numerical Simulation ◽  
Reynolds Number ◽  
Direct Numerical Simulation ◽  
Turbulent Flows ◽  
Channel Flow ◽  
Turbulent Channel Flow ◽  
Streamwise Velocity ◽  
Mean Velocity ◽  
Layer Structures ◽  
High Reynolds

A direct numerical simulation of incompressible channel flow at a friction Reynolds number ($\mathit{Re}_{{\it\tau}}$) of 5186 has been performed, and the flow exhibits a number of the characteristics of high-Reynolds-number wall-bounded turbulent flows. For example, a region where the mean velocity has a logarithmic variation is observed, with von Kármán constant ${\it\kappa}=0.384\pm 0.004$. There is also a logarithmic dependence of the variance of the spanwise velocity component, though not the streamwise component. A distinct separation of scales exists between the large outer-layer structures and small inner-layer structures. At intermediate distances from the wall, the one-dimensional spectrum of the streamwise velocity fluctuation in both the streamwise and spanwise directions exhibits $k^{-1}$ dependence over a short range in wavenumber $(k)$. Further, consistent with previous experimental observations, when these spectra are multiplied by $k$ (premultiplied spectra), they have a bimodal structure with local peaks located at wavenumbers on either side of the $k^{-1}$ range.

The Fully Developed Wake of a Circular Cylinder

1949 ◽  
Vol 2 (4) ◽  
pp. 451 ◽  
Author(s):  
AA Townsend
Keyword(s):  
Circular Cylinder ◽  
Diffusion Coefficients ◽  
Large Scale ◽  
Turbulent Transport ◽  
Turbulent Energy ◽  
Small Scale ◽  
Mean Velocity ◽  
Turbulent Fluid ◽  
Air Stream ◽  
Scale Motion

Extending previous work on turbulent diffusion in the wake of a circular-cylinder, a series of measurements have been made of the turbulent transport of mean stream momentum, turbulent energy, and heat in the wake of a cylinder of 0.169 cm. diameter, placed in an air-stream of velocity 1280 cm. sec.-1. It has been possible to extend the measurements to 960 diameters down-stream from the cylinder, and it 1s found that, at distances in excess of 600 diameters, the requirements of dynamical similarity are very nearly satisfied. To account for the observed rates of transport of turbulent energy and heat, it is necessary that only part of this transport be due to bulk convection by the slow large-scale motion of the jets of turbulent fluid emitted by the central, fully turbulent core of the wake, which had been supposed previously to perform most of the transport. The remainder of the transport is carried out by the small-scale diffusive motion of the turbulent eddies within the jets, and may be described by assigning diffusion coefficients to the turbulent fluid. It is found that the diffusion coefficients for momentum and heat are approximately equal, but that for turbulent energy is considerably smaller. On the basis of these hypotheses, it is possible to calculate $he form of the mean velocity distribution in good agreement with experiment, and to give a qualitative explanation of the apparently more rapid diffusion of heat.

scholarly journals On the structure of the self-sustaining cycle in separating and reattaching flows

2018 ◽  
Vol 857 ◽  
pp. 907-936 ◽  
Author(s):  
A. Cimarelli ◽  
A. Leonforte ◽  
D. Angeli
Keyword(s):  
Shear Layer ◽  
Rectangular Plate ◽  
Large Scale ◽  
Reverse Flow ◽  
Leading Edge ◽  
Streamwise Velocity ◽  
The Self ◽  
Small Scale ◽  
Spectral Evolution ◽  
Mean Velocity

The separating and reattaching flows and the wake of a finite rectangular plate are studied by means of direct numerical simulation data. The large amount of information provided by the numerical approach is exploited here to address the multi-scale features of the flow and to assess the self-sustaining mechanisms that form the basis of the main unsteadinesses of the flows. We first analyse the statistically dominant flow structures by means of three-dimensional spatial correlation functions. The developed flow is found to be statistically dominated by quasi-streamwise vortices and streamwise velocity streaks as a result of flow motions induced by hairpin-like structures. On the other hand, the reverse flow within the separated region is found to be characterized by spanwise vortices. We then study the spectral properties of the flow. Given the strongly inhomogeneous nature of the flow, the spectral analysis has been conducted along two selected streamtraces of the mean velocity field. This approach allows us to study the spectral evolution of the flow along its paths. Two well-separated characteristic scales are identified in the near-wall reverse flow and in the leading-edge shear layer. The first is recognized to represent trains of small-scale structures triggering the leading-edge shear layer, whereas the second is found to be related to a very large-scale phenomenon that embraces the entire flow field. A picture of the self-sustaining mechanisms of the flow is then derived. It is shown that very-large-scale fluctuations of the pressure field alternate between promoting and suppressing the reverse flow within the separation region. Driven by these large-scale dynamics, packages of small-scale motions trigger the leading-edge shear layers, which in turn created them, alternating in the top and bottom sides of the rectangular plate with a relatively long period of inversion, thus closing the self-sustaining cycle.

scholarly journals Flow topologies in primary atomization of liquid jets: a direct numerical simulation analysis

2018 ◽  
Vol 859 ◽  
pp. 819-838 ◽  
Author(s):  
Josef Hasslberger ◽  
Sebastian Ketterl ◽  
Markus Klein ◽  
Nilanjan Chakraborty
Keyword(s):  
Numerical Simulation ◽  
Reynolds Number ◽  
Direct Numerical Simulation ◽  
Incompressible Flows ◽  
Flow Structures ◽  
Liquid Jets ◽  
Small Scale ◽  
Flow Topology ◽  
Local Flow ◽  
Turbulent Length Scale

The local flow topology analysis of the primary atomization of liquid jets has been conducted using the invariants of the velocity-gradient tensor. All possible small-scale flow structures are categorized into two focal and two nodal topologies for incompressible flows in both liquid and gaseous phases. The underlying direct numerical simulation database was generated by the one-fluid formulation of the two-phase flow governing equations including a high-fidelity volume-of-fluid method for accurate interface propagation. The ratio of liquid-to-gas fluid properties corresponds to a diesel jet exhausting into air. Variation of the inflow-based Reynolds number as well as Weber number showed that both these non-dimensional numbers play a pivotal role in determining the nature of the jet break-up, but the flow topology behaviour appears to be dominated by the Reynolds number. Furthermore, the flow dynamics in the gaseous phase is generally less homogeneous than in the liquid phase because some flow regions resemble a laminar-to-turbulent transition state rather than fully developed turbulence. Two theoretical models are proposed to estimate the topology volume fractions and to describe the size distribution of the flow structures, respectively. In the latter case, a simple power law seems to be a reasonable approximation of the measured topology spectrum. According to that observation, only the integral turbulent length scale would be required as an input for the a priori prediction of the topology size spectrum.

Sign in / Sign up

Export Citation Format

Share Document