Frequency reconfigurable dual-band MIMO antenna using pentagon slot resonator with improved bandwidth

2017 ◽  
Vol 10 (3) ◽  
pp. 383-389
Author(s):  
Deepali Borakhade ◽  
Sanjay Pokle
Keyword(s):  
Multiple Input Multiple Output ◽  
Dual Band ◽  
Pin Diode ◽  
Vehicular Communication ◽  
Pin Diodes ◽  
Band Frequency ◽  
Mimo Antenna ◽  
Slot Line ◽  
Multiple Input ◽  
Input Multiple Output

In this paper, multiple-input–multiple output (MIMO) antenna with dual-band frequency reconfiguration is presented. The proposed antenna consists of two symmetrical pentagon radiating elements. These radiating elements support bands of 1.5 GHz (GPS) and 2.4 GHz (Wi-Fi) frequency. The two PIN diodes are appropriately located on slot line in order to control the current flowing through the radiator. All simulated results are compared and confirmed with measured results. The antenna has VSWR ⩽1.8 and isolation of −28 dB. The advantage of this antenna is that bandwidth is increased by switching of PIN diode in the range from 80 MHz up to maximum 300 MHz. These characteristics demonstrate that proposed antenna is an attractive solution for a multimode application such as GPS, Wi-Fi routers, vehicular communication, etc. where wideband is required.

scholarly journals Dual-Band 2 × 2 MIMO Antenna with Compact Size and High Isolation Based on Half-Mode SIW

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Abubaker Ahmed Elobied ◽  
Xue-Xia Yang ◽  
Ningjie Xie ◽  
Steven Gao
Keyword(s):  
Multiple Input Multiple Output ◽  
Dual Band ◽  
Antenna Element ◽  
Mimo Antenna ◽  
High Isolation ◽  
Rectangular Patch ◽  
Compact Size ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Proximity Coupling

This paper presents a close-spaced dual-band 2 × 2 multiple-input multiple-output (MIMO) antenna with high isolation based on half-mode substrate integrated waveguide (HMSIW). The dual-band operation of the antenna element is achieved by loading a rectangular patch outside the radiating aperture of an HMSIW cavity. The HMSIW cavity is excited by a coaxial probe, whereas the rectangular patch is energized through proximity coupling by the radiating aperture of HMSIW. The antenna elements can be closely placed using the rotation and orthogonal arrangement for a 2 × 2 array. Small neutralization lines at the center of the MIMO antenna can increase the isolation among its elements by around 10 dB in the lower band and 5 dB in the higher band. A prototype of the MIMO antenna is fabricated and its performance is measured. The measured results show that the resonant frequencies are centered at 4.43 and 5.39 GHz with bandwidths of 110 and 80 MHz and peak gains of 6 and 6.4 dBi, respectively. The minimum isolation in both bands is greater than 35 dB. The envelope correlation coefficient is lower than 0.005 within two operating bands.

scholarly journals Design of a compact hexagonal structured dual band MIMO antenna using orthogonal polarization for WLAN and satellite applications

2019 ◽  
Vol 9 (5) ◽  
pp. 4217
Author(s):  
Aziz Dkiouak ◽  
Mohssine El Ouahabi ◽  
Alia Zakriti ◽  
Mohsine Khalladi ◽  
Aicha Mchbal
Keyword(s):  
Multiple Input Multiple Output ◽  
Antenna System ◽  
Dual Band ◽  
Orthogonal Polarization ◽  
Mimo Antenna ◽  
X Band ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Satellite Applications ◽  
Strip Lines

In this paper, a compact dual band multiple-input multiple-output (MIMO) antenna system for WLAN and X-band satellite applications (2.4/9.8 GHz respectively) is proposed. On the top face of the substrate, two antenna elements with a size of 20 × 24 mm2 are placed side by side and fed with matched orthogonal micro-strip lines. The two antenna elements have orthogonal polarization which can reduce the mutual coupling between its ports. The designed antenna system is fabricated and measured to validate the simulation results. The impedance bandwidths are about 370 MHz (2.19 to 2.56 GHz) and 630 MHz (9.44 to 10.07 GHz), while the obtained isolation is greater than 14 dB at the operating bands. Furthermore, the envelope correlation is less than 0.052 and 0.008 at 2.4 and 9.8 GHz, respectively. Hence the diversity gain is higher than 9.98 in the frequency bands of interest.

scholarly journals Dual Band Notched UWB MIMO Antenna for Surfaces Penetrating Application

2019 ◽  
Vol 8 (3) ◽  
pp. 6-15
Author(s):  
A. Chaabane ◽  
A. Babouri
Keyword(s):  
Low Cost ◽  
Multiple Input Multiple Output ◽  
Ultra Wideband ◽  
Dual Band ◽  
Mimo Antenna ◽  
Compact Size ◽  
Multiple Input ◽  
Input Multiple Output ◽  
White Portland Cement ◽  
Compact Planar

This paper introduces a novel compact planar Ultra-Wideband (UWB) Multiple-Input-Multiple-Output (MIMO) antenna with dual-band notched performance for Surfaces Penetrating (SP) application. To avoid interference from co-existing systems, two notched bands are introduced by including strips inside the radiating patches. The two ports MIMO antenna is printed on the low-cost FR4 substrate having a compact size of 56×32.47×1.5 mm3. The measured results indicate that the −10 dB bandwidth of the proposed MIMO antenna covers a wide bandwidth from 1.57 GHz to 12.4 GHz (155.05%) with dual-band rejection (2.04 GHz – 3.98 GHz and 4.8 GHz – 6.22 GHz). The effects of numerous construction and decoration surfaces on the antenna’s reflection coefficients are measured. Gypsum, White Portland Cement, Slate, Marble, Wood and Reinforced Concrete were tested. A good penetrating capability is measured which confirms the aptitude of the proposed MIMO antenna to work as SP antenna.

Dual-band-notched UWB MIMO antennas with miniaturization using half-cutting technology

2021 ◽  
pp. 1-8
Author(s):  
Zhonghong Du ◽  
Xiaohui Zhang ◽  
Peiyu Qin ◽  
Yanning Yuan ◽  
Jiangfan Liu ◽  
...  
Keyword(s):  
Multiple Input Multiple Output ◽  
Ultra Wideband ◽  
Dual Band ◽  
Uwb Antenna ◽  
Radiation Characteristics ◽  
Mimo Antenna ◽  
Mimo Antennas ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Continuous Bending

Abstract A compact four-element ultra-wideband (UWB) multiple-input–multiple-output (MIMO) antenna with dual polarization and dual-notched capabilities was developed and fabricated. The MIMO antenna is composed of four orthogonally placed half-cutting UWB antenna elements. This orthogonal placement improves the isolation. Furthermore, an L-shaped slot and a continuous bending slot are etched to realize the band-rejection function in the WiMAX and WLAN bands. The result shows that the antenna achieved operating bands of 2.9–16.5 GHz (140.2%, S11 < −10 dB), fully covering the UWB (3.1–10.6 GHz). The port isolation is greater than 23 dB in the frequency band of interest, excluding two rejected bands. Moreover, the MIMO antenna has excellent diversity performance, such as a low envelope correlation coefficient (<0.004), high diversity gain (approximately 10 dB), and good omnidirectional radiation characteristics.

Design of an interlocked four-port MIMO antenna for UWB automotive communications

2021 ◽  
pp. 1-8
Author(s):  
M. Saravanan ◽  
R. Kalidoss ◽  
B. Partibane ◽  
K. S. Vishvaksenan
Keyword(s):  
Multiple Input Multiple Output ◽  
Performance Estimation ◽  
Ultra Wideband ◽  
Antenna Element ◽  
Frequency Range ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Operating Bandwidth ◽  
Peak Gain

Abstract The design, analysis, fabrication, and testing of a four-port multiple-input multiple-output (MIMO) antenna is reported in this paper for automotive communications. The MIMO antenna is constructed using the basic antenna element exploiting a slot geometry. Two such antennas are developed on the same microwave laminate to develop a two-port MIMO antenna. Two such microwave laminates are interlocked to create the four-port MIMO scheme. The most distinct feature of the proposed architecture is that the inter-port isolation is well-taken care without the need for an external decoupling unit. The four-port MIMO antenna has an overall volume of 32 × 15 × 32 mm3. The prototype MIMO antenna is fabricated and the measurements are carried out to validate the simulation results. The antenna offers ultra-wideband (UWB) characteristics covering the frequency range of 2.8–9.5 GHz. The average boresight gain of the antenna ranges from 3.2 to 5.41 dBi with the peak gain at 8 GHz. The simulated efficiency of the antenna is greater than 73% within the operating bandwidth. The MIMO parameters such as envelope correlation coefficient, diversity gain, and mean effective gain are evaluated and presented. The appropriateness of the proposed antenna for deployment in the shark fin housing of the present-day automobiles is verified using on-car performance estimation.

scholarly journals Mutual Coupling Reduction of DRA for MIMO Applications

2019 ◽  
Vol 8 (1) ◽  
pp. 75-81
Author(s):  
N. Al Shalaby ◽  
S. G. El-Sherbiny
Keyword(s):  
Mutual Coupling ◽  
Dielectric Material ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Antenna System ◽  
Parasitic Element ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Element Method

In this paper, A multiple input Multiple Output (MIMO) antenna using two Square Dielectric Resonators (SDRs) is introduced. The mutual coupling between the two SDRAs is reduced using two different methods; the first method is based on splitting a spiral slot in the ground plane, then filling the slot with dielectric material, "E.=2.2". The second method is based on inserting a copper parasitic element, having the same shape of the splitted Spiral, between the two SDRAs.  The effect of replacing the copper parasitic element with Carbon nanotubes (CNTs) parasitic element "SOC12 doped long-MWCNT BP" is also studied. The antenna system is designed to operate at 6 GHz. The analysis and simulations are carried out using finite element method (FEM). The defected ground plane method gives a maximum isolation of l8dB at element spacing of 30mm (0.6λo), whereas the parasitic element method gives a maximum isolation of 42.5dB at the same element spacing.

scholarly journals DESIGN AND ANALYSIS OF COMPACT METAMATERIAL MIMO ANTENNA FOR WLAN APPLICATIONS

2019 ◽  
Vol 57 (2) ◽  
pp. 223
Author(s):  
Hoa Nguyen Thi Quynh ◽  
Sy Tuan Tran ◽  
Huu Lam Phan ◽  
Duy Tung Phan
Keyword(s):  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Split Ring Resonator ◽  
Antenna Element ◽  
Mimo Antenna ◽  
Complementary Split Ring Resonator ◽  
Antenna Performance ◽  
Multiple Input ◽  
Input Multiple Output ◽  
The Individual

A compact three-port metamaterial multiple-input-multiple-output (MIMO) antenna using complementary split-ring resonator (CSRR) loaded ground have demonstrated in order to miniaturize the size and improve the antenna performance. The antenna is designed on FR4 material and simulated by HFSS software. By loading CSRRs in the ground plane, the size reduction of 77% of the individual patch antenna element is achieved, which appeared to be the major reason for the obtained the compact MIMO antenna. Furthermore, the simulated results show that the proposed MIMO antenna achieves the total gain higher than 5 dB, the isolation less than -11 dB, the envelope correlation coefficient (ECC) value lower than 0.015, and the bandwidth of 100 MHz through the whole WLAN band from 2.4 GHz to 2.484 GHz, indicating promises for WLAN applications.

scholarly journals Compact Dual-Band Circularly Polarized Stacked Patch Antenna for Microwave-Radio-Frequency Identification Multiple-Input-Multiple-Output Application

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Enze Zhang ◽  
Andrea Michel ◽  
Paolo Nepa ◽  
Jinghui Qiu
Keyword(s):  
Radio Frequency ◽  
Radio Frequency Identification ◽  
Patch Antenna ◽  
Multiple Input Multiple Output ◽  
Dual Band ◽  
Circularly Polarized ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Frequency Identification ◽  
Stacked Patch Antenna

A compact, low-profile, two-port dual-band circularly polarized (CP) stacked patch antenna for radio-frequency identification (RFID) multiple-input-multiple-output (MIMO) readers is proposed, which employs the shared-aperture technique. The proposed antenna adopts a 1.524 mm thickness Rogers Ro4350b substrate with relative permittivity of 3.48. Two pairs of isolated ports are working at two microwave- (MW-) RFID bands (2.4–2.485 GHz and 5.725–5.875 GHz) with high port isolation of 25 dB and 30 dB, respectively. A shared metal slot layer is designed to separate two feeding structures of the lower band and upper band for port isolation enhancement as well as saving space. Corner-truncated square slot and patch configurations have been designed to obtain CP modes. In the lower and upper MW-RFID bands, the relative impedance bandwidths are 12.2% and 5.7%, and the maximum realized gains are higher than 7.3 dBic. Moreover, two-element configurations have been combined for an RFID MIMO system that occupies a dimension of 119 mm × 119 mm × 12.9 mm. The MIMO antenna performance of envelope correlation coefficient (ECC) is lower than 0.03, and diversity gain is close to 10 dB.

Sign in / Sign up

Export Citation Format

Share Document