Minimized Triple-Band Eight-Element Antenna Array for 5G Metal-frame Smartphone Applications

A multiple-input-multiple-output (MIMO) antenna array for triple-band 5G metal-frame smartphone applications is proposed in this paper. Each single antenna element consists of an S-shaped feeding strip and an L-shaped radiation strip on the metal frame. The dimension of the antenna element is only 6.5 mm × 7 mm (0.076 λ0 × 0.082 λ0, λ0 is the free-space wavelength at the frequency of 3.5 GHz). The −6 dB impedance bandwidth of the proposed eight-antenna array can cover 3.3–3.8 GHz, 4.8–5 GHz, and 5.15–5.925 GHz. The evolution design and the analysis of the optimal parameters for a single antenna element are derived to investigate the principle of the antenna. The measured total efficiency is larger than 70%. The measured isolation is better than 13 dB. The measurements of the prototype agree well with the simulation results.

Dielectric Slabs-Based Lens for Millimeter-Wave Beamforming

This paper proposes a dielectric slabs-based lens for millimeter-wave beamforming systems. The proposed lens is based on the graded steps of the effective refractive index of the semi-spherical lens. It consists of multiple dielectric slabs that match the selected gradient effective refractive index. These slabs have the same thicknesses and different radii. The slab thickness in this lens should not exceed a quarter of the operating wavelength to keep on a similar effective refractive index of the original semi-spherical lens. A horn antenna is used to examine the performance of the designed lens at 28 GHz frequency in terms of the maximum gain, sidelobe level, and 3 dB beamwidth. Sixteen switchable horn antennas are used to demonstrate lens capability for millimeter-wave beamforming. Every single antenna element is selected individually, thus the dielectric lens steers and enhances the corresponding radiation of the selected element in the desired direction.

3-D twelve-port multi-service diversity antenna for automotive communications

This paper presents a twelve-port ultra-wideband multiple-input-multiple-output (MIMO)/diversity antenna integrated with GSM and Bluetooth bands. The twelve-port antenna is constructed by arranging four elements in the horizontal plane and eight elements in the vertical plane. The antenna element, which is created using a simple rectangular monopole, exhibits a frequency range of 3.1 to 12 GHz. The additional Bluetooth and GSM bands are achieved by introducing stubs into the ground plane. The size of the MIMO antenna is 100 × 100 mm2. The antenna offers polarization diversity, with vertical and horizontal polarization in each plane. The diversity antenna has a bandwidth of 1.7–1.9 GHz, 2.35–2.55 GHz, and 3–12 GHz, the radiation efficiency of 90%, and peak gain of 2.19 dBi. The proposed antenna offers an envelope correlation coefficient of < 0.12, apparent diversity gain of > 9.9 dB, effective diversity gain of > 8.9 dB, mean effective gain of < 1 dB, and channel capacity loss of < 0.35 bits/s/Hz. Also, the MIMO antenna is tested for housing effects in order to determine its suitability for automotive applications.

High Gain Beam Steering Antenna Arrays with Low Scan Loss for mmWave Applications

In millimeter-wave (mmWave) communications, the antenna gain is a crucial parameter to overcome path loss and atmospheric attenuation. This work presents the design of two cylindrical conformal antenna arrays, made of modified rectangular microstrip patch antenna as a radiating element, working at 28 GHz for mmWave applications providing high gain and beam steering capability. The microstrip patch antenna element uses Rogers RO4232 substrate with a thickness of 0.5 mm and surface area of 5.8 mm × 5.8 mm. The individual antenna element provides a gain of 6.9 dBi with return loss bandwidth of 5.12 GHz. The first antenna array, made by using five conformal antenna elements, achieves a uniform gain of approximately 12 dBi with minimal scan loss for extensive scan angles. In the second antenna array, a dielectric superstrate using Rogers TMM (10i) was used to modify the first antenna array. It enhanced the gain to approximately 16 dBi while still maintaining low scan loss for wide angles. The proposed array design method is very robust and can be applied to any conformal surface. The mathematical equations are also provided to derive the array design, and both array designs are verified by using full-wave simulations.

An Experiment-Based Comparison between Fully Digital and Hybrid Beamforming Radio Architectures for Many-Antenna Full-Duplex Wireless Communication

Full-duplex (FD) communication in many-antenna base stations (BSs) is hampered by self-interference (SI). This is because a FD node’s transmitting signal generates significant interference to its own receiver. Recent works have shown that it is possible to reduce/eliminate this SI in fully digital many-antenna systems, e.g., through transmit beamforming by using some spatial degrees of freedom to reduce SI instead of increasing the beamforming gain. On a parallel front, hybrid beamforming has recently emerged as a radio architecture that uses multiple antennas per FR chain. This can significantly reduce the cost of the end device (e.g., BS) but may also reduce the capacity or SI reduction gains of a fully digital radio system. This is because a fully digital radio architecture can change both the amplitude and phase of the wireless signal and send different data streams from each antenna element. Our goal in this paper is to quantify the performance gap between these two radio architectures in terms of SI cancellation and system capacity, particularly in multi-user MIMO setups. To do so, we experimentally compare the performance of a state-of-the-art fully digital many antenna FD solution to a hybrid beamforming architecture and compare the corresponding performance metrics leveraging a fully programmable many-antenna testbed and collecting over-the-air wireless channel data. We show that SI cancellation through beam design on a hybrid beamforming radio architecture can achieve capacity within 16% of that of a fully digital architecture. The performance gap further shrinks with a higher number of quantization bits in the hybrid beamforming system.

Performance Improvement of Substrate Integrated Cavity Fed Dipole Array Antenna Using ENZ Metamaterial for 5G Applications

This paper exhibits a high-gain, low-profile dipole antenna array (DAA) for 5G applications. The dipole element has a semi-triangular shape to realize a simple input impedance regime. To reduce the overall antenna size, a substrate integrated cavity (SIC) is adopted as a power splitter feeding network. The transition between the SIC and the antenna element is achieved by a grounded coplanar waveguide (GCPW) to increase the degree of freedom of impedance matching. Epsilon-near-zero (ENZ) metamaterial technique is exploited for gain enhancement. The ENZ metamaterial unit cells of meander shape are placed in front of each dipole perpendicularly to guide the radiated power into the broadside direction. The prospective antenna has an overall size of 2.58 λg3 and operates from 28.5 GHz up to 30.5 GHz. The gain is improved by 5 dB compared to that of the antenna without ENZ unit cells, reaching 11 dBi at the center frequency of 29.5 GHz. Measured and simulated results show a reasonable agreement.

Modified 16-Quasi Log Periodic Antenna Array for Microwave Imaging of Breast Cancer Detection

In this paper, an effective system for microwave imaging of breast tumor detection using modified 16-planar log periodic antenna (PLPA) array is presented. The modified PLPA operates in the band from 2 to 5 GHz with stable directional patterns in the end-fire direction. Once the results of a single antenna element have been validated, the design is extended to include 16 antenna elements. All 16 transceiver antennas are vertically placed around the phantom in a circular manner where one antenna acts as a transmitter and the rest work as receivers. Delay and Sum (DAS) algorithm is used for post processing the acquired scattered signals from the sensors to reconstruct the image of the breast and to identify the existence of breast tumors. The electromagnetic simulators CST and HFSS are used to design the system, while MATLAB is used to process the data. The developed PLPA array-based microwave imaging system performs admirably, making it one of the most effective systems for detecting tumor cells.

Light-weight wideband antenna array with low sidelobes for SAR applications

Purpose The purpose of this study is to achieve the low-cost, light-weight and compact antenna array with wide bandwidth and low side lobe levels for synthetic aperture radar (SAR) applications in Ku frequency band. Design/methodology/approach A compact design of a rectangular microstrip patch antenna array using multilayered dielectric structure is presented in Ku-band for advanced broadband SAR systems. In this design, stepped pins are used to connect the microstrip feed lines to the radiating patches. Findings The simulation and fabrication results of the multilayered antenna and a 1×16-element linear array of the antenna with Taylor amplitude distribution in the feeding network are presented. The antenna element has a 10-dB impedance bandwidth of more than 26%, and the linear array shows reduction in bandwidth percentage (about 15.4%). Thanks to Taylor amplitude tapering, the side lobe level (SLL) of the array is lower than −24 dB. The maximum measured gains of the antenna element and the linear array are 7 and 19.2 dBi at the center frequency, respectively. Originality/value In the communication systems, a high gain narrow beamwidth radiation pattern achieved by an array of multiple antenna elements with optimized spacing is a solution to overcome the path loss, atmospheric loss, polarization loss, etc. Also, wideband characteristics and compact size are desirable in satellite and SAR systems. This paper provides the combination of these features by microstrip structures.

Double Overt-Leaf Shaped CPW-Fed Four Port UWB MIMO Antenna

This paper presents a 4 × 4 multi-input multi-output antenna array for ultra-wideband applications. The single element of the array is comprised of a modified co-planar waveguide-fed double overt-leaf shaped patch radiator. The co-planar ground is optimized to achieve maximum impedance matching in the operating frequency band. The results show that the single antenna element offers an impedance bandwidth of 13.2 GHz starting from 3.2 GHz to 16.7 GHz. It is also observed from the results that the antenna offers good radiation characteristics and acceptable gain for the frequency band of interest. Furthermore, a 4 × 4 MIMO array is designed by utilizing the polarization diversity technique. To improve the isolation performance among antenna elements, a fan-shaped decoupler is introduced on the other side of the substrate, which ensures minimum isolation of 20 dB. Moreover, the proposed MIMO array operates in the frequency range of 2.75–16.05 GHz. The proposed MIMO array is fabricated and measured for the validation of simulation results, and it is observed that both the results are well in agreement.

A simple and effective broadband decoupling structure for UWB-MIMO antenna

A new type of closed square ring decoupling structure is proposed in this letter, which can effectively reduce the coupling of antennas. The designed antenna is composed of two elliptical monopoles and a common ground loaded with a broadband parasitic decoupling structure. Considering the impedance matching, each antenna element is changed from the original rectangular microstrip feed to a tapered microstrip feed and etched a circular slot on the elliptical monopole patch. By comparison with the original antenna without any decoupling structure, through loading the broadband decoupling structure on the ground, the antenna isolation is improved by 10 dB in most frequency bands. Comparing simulation and measurement results, the antenna achieves better than 25 dB isolation over the whole operating band (3.3–12 GHz). By manufacturing and testing the antenna designed in this article, the excellent performance parameters obtained also prove that the antenna can be used in portable devices.