Improved internal bond strength of high-density particle boards containing formaldehyde-free whey-based resins on addition of phthalic anhydride

1986 ◽  
Vol 25 (2) ◽  
pp. 313-315 ◽  
Author(s):  
Tito Viswanathan ◽  
Terry Gilton
Keyword(s):  
Bond Strength ◽  
Phthalic Anhydride ◽  
Internal Bond ◽  
High Density ◽  
Internal Bond Strength

scholarly journals Influence of Adding Offcuts and Trims with a Recycling Approach on the Properties of High-Density Fibrous Composites

Polymers ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1327
Author(s):  
Conrad M. Sala ◽  
Eduardo Robles ◽  
Grzegorz Kowaluk
Keyword(s):  
Mechanical Properties ◽  
Bond Strength ◽  
Water Absorption ◽  
Internal Bond ◽  
High Density ◽  
Raw Material ◽  
Internal Bond Strength ◽  
Fibrous Composites ◽  
Thickness Swelling ◽  
Linear Decrease

The sizeable global production of wood-based products requires new sources of raw material, but also creates large quantities of wastes or composites that do not comply with requirements. In this study, the influence of different shares of recovered high-density fiberboards (HDF-r), reversed into the production, on industrial HDF properties, has been examined. HDF-r may be a suitable partial substitute for raw pinewood for industrial HDF production. Although most of the mechanical properties, as well as thickness swelling and water absorption, had a linear decrease with the increase in the share of HDF-r share, the elaborated boards met most of the commercial requirements (EN 622-5). The property that did not meet the requirements was the internal bond strength for panels with 10% of HDF-r. The presented results show that, after some adjustments, it should be possible to produce HDF boards with up to 10% of recycled HDF being able to meet all commercial requirements.

scholarly journals Sifat Papan Partikel Bambu Petung (Dendrocalamus asper) dan Bambu Wulung (Gigantochloa atroviolacea) dengan Perlakuan Ekstraksi

2020 ◽  
Vol 14 (1) ◽  
pp. 84
Author(s):  
Ragil Widyorini ◽  
Ikhwan Syahri ◽  
Greitta Kusuma Dewi
Keyword(s):  
Citric Acid ◽  
Bond Strength ◽  
Internal Bond ◽  
Cold Water ◽  
Internal Bond Strength ◽  
Modulus Of Rupture ◽  
Bamboo Species ◽  
Japanese Industrial Standard ◽  
Dendrocalamus Asper ◽  
Extraction Treatment

Bambu memiliki kandungan ekstraktif dengan persentase yang berbeda antar jenis bambu. Penelitian ini bertujuan untuk mengetahui pengaruh perlakuan ekstraksi pada jenis bambu yang berbeda terhadap sifat papan partikel. Dua jenis bambu digunakan yaitu Bambu Petung (Dendrocalamus asper) dan Bambu Wulung (Gigantochloa atroviolacea). Perlakuan ekstraksi digunakan pada partikel bambu sebelum proses pembuatan papan partikel yaitu tanpa ekstraksi, ekstraksi air dingin dan ekstraksi air panas. Papan partikel dibuat dalam ukuran 25 cm x 25 cm x 0,7 cm, target kerapatan 0,9 g/cm3, jumlah asam sitrat 30%, serta kondisi pengempaan suhu 180°C selama 10 menit. Hasil penelitian menunjukkan bahwa interaksi perlakuan ekstraksi dan jenis bambu hanya berpengaruh signifikan pada sifat penyerapan air dan keteguhan rekat internal, sedangkan jenis bambu berpengaruh signifikan pada nilai kadar air, modulus patah dan modulus elastisitas. Semua papan partikel yang dihasilkan memenuhi standar Japanese Industrial Standard (JIS) A 5908 tipe 13. Pada penelitian ini, papan partikel dari bambu wulung tanpa perlakuan ekstraksi mempunyai nilai yang memenuhi standar tipe 18 dan berpotensi sebagai bahan baku untuk produk furnitur eksterior. Perlakuan ekstraksi dapat meningkatkan secara signifikan nilai keteguhan rekat internal papan partikel bambu petung, walaupun secara umum dengan jumlah asam sitrat 30% perlakuan tersebut tidak diperlukan pada papan partikel bambu Properties of Particleboard made from Petung Bamboo (Dendrocalamus asper) and Wulung Bamboo (Gigantochloa atroviolacea) Particles with Extraction TreatmentAbstractBamboo has extractives, which the percentage of extractive was different based on bamboo species. This research aimed to investigate the effect of extraction treatment at different bamboo species on the particleboard properties. Two types of bamboo were used, i.e. Petung bamboo (Dendrocalamus asper) and Wulung bamboo (Gigantochloa atroviolacea). Three extraction treatments were conducted to the bamboo particles before the particleboard manufacture, i.e. unextracted, cold-water extraction, and hot-waterextraction. The particleboard was made in the size of 25 cm x 25 cm x 0.7 cm, target density of 0.9 g/cm³, citric acid content of 30%, and pressing temperature of 180°C for 10 min. The results showed that the interaction between extraction treatment and bamboo species significantly affected on the water absorption and internal bond strength, however bamboo species affected significantly on the moisture content, modulus of rupture, and modulus of elasticity. All of particleboards could met the requirement of the 13 type of Japanese Industrial Standard (JIS) A 5908. In this research, particleboards made from wulung bamboo particles without extraction treatment have properties that met the requirement of the 18 type and the products have potential to be as exterior materials for furniture. In general, an extraction treatment was not an important step on the manufacturing of bamboo particleboard using citric acid 30% as adhesive. However, the extraction treatment could increase significantly the internal bond strength of particleboard made from petung bamboo.

scholarly journals Some advantages of three-layer medium-density fibreboard as compared to the traditional single-layer one

2019 ◽  
Vol 65 (1) ◽  
Author(s):  
Turgay Akbulut ◽  
Nadir Ayrilmis
Keyword(s):  
Bond Strength ◽  
Internal Bond ◽  
Single Layer ◽  
Middle Layer ◽  
Resin Content ◽  
Internal Bond Strength ◽  
Medium Density ◽  
Medium Density Fibreboard ◽  
Uf Resin ◽  
Layer Medium

Abstract The aim of the study was to develop three-layer medium-density fibreboard (MDF) manufacture by adding the coarse fibres in the middle layer, like three-layer particleboard. The liquid urea–formaldehyde (UF) resin was reduced from 10.5 to 6.5 wt% in the middle layer of the MDFs. The UF resin content was kept constant at 10 wt% in the surface layers of all the MDFs. Moreover, the average density of MDFs was decreased from 730 to 650 kg/m3. The internal bond strength of three-layer MDFs decreased with decreasing UF resin content (10.5 to 8.5 wt%) in the middle layer. However, the decreases in the internal bond strength were statistically not significant. The internal bond strength values of the MDFs having density between 730 and 675 kg/m3 did not show significant differences. The cost savings of the resin were 20% when the amount of resin was reduced from 10.5 to 8.5 wt%. Three-layer MDFs had lower resin consumption at lower densities over traditional single-layer MDFs produced in the same plant with the same material components without decreasing their technological properties. In conclusion, it can be said that three-layer MDF could be produced at a lower cost than traditional single-layer MDF.

Effects of water soaking and outdoor exposure on modulus of rupture and internal bond strength of particleboard

2013 ◽  
Vol 60 (2) ◽  
pp. 127-133 ◽  
Author(s):  
Hideaki Korai ◽  
Hiroshi Saotome ◽  
Masaharu Ohmi
Keyword(s):  
Bond Strength ◽  
Internal Bond ◽  
Outdoor Exposure ◽  
Internal Bond Strength ◽  
Modulus Of Rupture

scholarly journals Selected Properties of Overlaid Magnesium Based Composite Panels for Flooring

2020 ◽  
Vol 10 (15) ◽  
pp. 5028
Author(s):  
Fidan Aslanova ◽  
Gozen Elkiran ◽  
Salim Hiziroglu ◽  
Serkan Ilseven
Keyword(s):  
Bond Strength ◽  
Surface Quality ◽  
Internal Bond ◽  
Internal Bond Strength ◽  
Sample Type ◽  
Thickness Swelling ◽  
Mechanical And Physical Properties ◽  
Flooring Materials ◽  
Flooring Material

The objective of this work was to evaluate some of the mechanical and physical properties of the flooring materials manufactured from panels having magnesia substrate overlaid with oak veneer (Querqus alba) and linoleum sheets. Commercially manufactured panels were used in this work. Bending characteristics, internal bond strength, thickness swelling, and surface quality of the samples were evaluated. The highest modulus of elasticity (MOE) value of 4406 MPa for the sample type-A2 was loaded in the direction of the substrate followed by 3478 MPa for linoleum covered samples which were loaded in the same direction. Internal bond strength values of the panels did not show any significant differences from each other. Dimensional stability of the specimens in the form of thickness swelling for both 2-h and 24-h water soaking tests resulted in values ranging from 0.11 to 0.19%. The surface quality of the samples was not substantially influenced as a function of water exposure. Based on the results in this work magnesium substrate overlaid with oak veneer and linoleum panels could have potential to be used as flooring material with accepted properties.

scholarly journals Effects of Flat-Shaped Face Layer Particles and Core Layer Particles of Intentionally Greater Thickness on the Properties of Wood-Reduced Particleboard

Fibers ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 46 ◽  
Author(s):  
Jan T. Benthien ◽  
Martin Ohlmeyer
Keyword(s):  
Bond Strength ◽  
Internal Bond ◽  
Core Layer ◽  
Adhesive Bond ◽  
Internal Bond Strength ◽  
Sieve Analysis ◽  
Scale Production ◽  
Bending Properties ◽  
Face Layer ◽  
Shaped Particle

Against the background of the intention to reduce the amount of wood used in the production of particleboard for economic reasons, the associated reduction in panel density and consequently the panel properties, the influence of the alternative use of flat-shaped face layer particles and core layer particles of intentionally greater thickness on the panel properties was investigated. Appropriate particles were made for this purpose, panels with typical (650 kg/m3) and reduced wood usage (500 kg/m3) were produced, and e.g., their bending properties and internal bond strength were determined. Particle size characterization was done with sieve analysis, image analysis (length and width measurement), and manual thickness gauging. It was found that the alternative use of the flat-shaped particle significantly increased the bending properties and thus the level of the reference can be achieved despite the reduced use of wood. The reason for the increased bending properties was assumed to be the higher strength of the particles themselves and the more effective adhesive bond between the particles. The increase in internal bond strength when using alternative particles could be attributed solely the different production history (e.g., use of fresh cutting blades and laboratory scale production).

Prediction of internal bond strength in a medium density fiberboard process using multivariate statistical methods and variable selection

2008 ◽  
Vol 42 (7) ◽  
pp. 521-534 ◽  
Author(s):  
Nicolas André ◽  
Hyun-Woo Cho ◽  
Seung Hyun Baek ◽  
Myong-Kee Jeong ◽  
Timothy M. Young
Keyword(s):  
Variable Selection ◽  
Bond Strength ◽  
Statistical Methods ◽  
Internal Bond ◽  
Medium Density Fiberboard ◽  
Internal Bond Strength ◽  
Medium Density ◽  
Multivariate Statistical Methods ◽  
Multivariate Statistical

Improve regression-based models for prediction of internal-bond strength of particleboard using Buckingham’s pi-theorem

2013 ◽  
Vol 24 (4) ◽  
pp. 735-740 ◽  
Author(s):  
Akbar Rostampour Haftkhani ◽  
Mohammad Arabi
Keyword(s):  
Bond Strength ◽  
Internal Bond ◽  
Internal Bond Strength ◽  
Pi Theorem
Sign in / Sign up

Export Citation Format

Share Document