scholarly journals Sifat Papan Partikel Bambu Petung (Dendrocalamus asper) dan Bambu Wulung (Gigantochloa atroviolacea) dengan Perlakuan Ekstraksi

2020 ◽  
Vol 14 (1) ◽  
pp. 84
Author(s):  
Ragil Widyorini ◽  
Ikhwan Syahri ◽  
Greitta Kusuma Dewi
Keyword(s):  
Citric Acid ◽  
Bond Strength ◽  
Internal Bond ◽  
Cold Water ◽  
Internal Bond Strength ◽  
Modulus Of Rupture ◽  
Bamboo Species ◽  
Japanese Industrial Standard ◽  
Dendrocalamus Asper ◽  
Extraction Treatment

Bambu memiliki kandungan ekstraktif dengan persentase yang berbeda antar jenis bambu. Penelitian ini bertujuan untuk mengetahui pengaruh perlakuan ekstraksi pada jenis bambu yang berbeda terhadap sifat papan partikel. Dua jenis bambu digunakan yaitu Bambu Petung (Dendrocalamus asper) dan Bambu Wulung (Gigantochloa atroviolacea). Perlakuan ekstraksi digunakan pada partikel bambu sebelum proses pembuatan papan partikel yaitu tanpa ekstraksi, ekstraksi air dingin dan ekstraksi air panas. Papan partikel dibuat dalam ukuran 25 cm x 25 cm x 0,7 cm, target kerapatan 0,9 g/cm3, jumlah asam sitrat 30%, serta kondisi pengempaan suhu 180°C selama 10 menit. Hasil penelitian menunjukkan bahwa interaksi perlakuan ekstraksi dan jenis bambu hanya berpengaruh signifikan pada sifat penyerapan air dan keteguhan rekat internal, sedangkan jenis bambu berpengaruh signifikan pada nilai kadar air, modulus patah dan modulus elastisitas. Semua papan partikel yang dihasilkan memenuhi standar Japanese Industrial Standard (JIS) A 5908 tipe 13. Pada penelitian ini, papan partikel dari bambu wulung tanpa perlakuan ekstraksi mempunyai nilai yang memenuhi standar tipe 18 dan berpotensi sebagai bahan baku untuk produk furnitur eksterior. Perlakuan ekstraksi dapat meningkatkan secara signifikan nilai keteguhan rekat internal papan partikel bambu petung, walaupun secara umum dengan jumlah asam sitrat 30% perlakuan tersebut tidak diperlukan pada papan partikel bambu Properties of Particleboard made from Petung Bamboo (Dendrocalamus asper) and Wulung Bamboo (Gigantochloa atroviolacea) Particles with Extraction TreatmentAbstractBamboo has extractives, which the percentage of extractive was different based on bamboo species. This research aimed to investigate the effect of extraction treatment at different bamboo species on the particleboard properties. Two types of bamboo were used, i.e. Petung bamboo (Dendrocalamus asper) and Wulung bamboo (Gigantochloa atroviolacea). Three extraction treatments were conducted to the bamboo particles before the particleboard manufacture, i.e. unextracted, cold-water extraction, and hot-waterextraction. The particleboard was made in the size of 25 cm x 25 cm x 0.7 cm, target density of 0.9 g/cm³, citric acid content of 30%, and pressing temperature of 180°C for 10 min. The results showed that the interaction between extraction treatment and bamboo species significantly affected on the water absorption and internal bond strength, however bamboo species affected significantly on the moisture content, modulus of rupture, and modulus of elasticity. All of particleboards could met the requirement of the 13 type of Japanese Industrial Standard (JIS) A 5908. In this research, particleboards made from wulung bamboo particles without extraction treatment have properties that met the requirement of the 18 type and the products have potential to be as exterior materials for furniture. In general, an extraction treatment was not an important step on the manufacturing of bamboo particleboard using citric acid 30% as adhesive. However, the extraction treatment could increase significantly the internal bond strength of particleboard made from petung bamboo.

scholarly journals The potential of using forest waste as a raw material in particleboard manufacturing

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 7780-7795
Author(s):  
Halil İbrahim Şahin
Keyword(s):  
Bond Strength ◽  
Modulus Of Elasticity ◽  
Internal Bond ◽  
Cold Water ◽  
Raw Material ◽  
Internal Bond Strength ◽  
Modulus Of Rupture ◽  
Formaldehyde Resin ◽  
Forest Waste ◽  
Physical Density

Wood particles and a mixture of forest waste were investigated as raw material for the particleboard industry. Urea formaldehyde resin was used as the adhesive in the production of the particleboards. Some chemical (pH, dilute alkali solubility, hot and cold water solubility), physical (density, moisture, thickness swelling, and water absorption), mechanical (modulus of rupture, modulus of elasticity, internal bond strength, and screw holding strength) properties, as well as the contact angle values of the resulting particleboards were determined. Due to its needle litter and cone content, the forest waste exhibited a lower pH value and a higher content of extractive material than wood. Increasing the addition of forest waste led to significant reductions in the physical and mechanical properties of the particleboards. The addition of forest waste reduced the internal bond strength the most (56.6%), whereas the least reduction (15.7%) was in the value of screw holding strength perpendicular to the surface. The values of all panels except panel type F exceeded the minimum modulus of elasticity (1600 N mm-2) required for furniture production according to the EN 312-P2 standard. Results of the analyses showed that forest waste (10% and 20%) is a suitable renewable raw material source for panel production.

scholarly journals SIFAT PAPAN PARTIKEL DARI SERAT TANDAN KOSONG SAWIT DAN SERBUK KAYU DENGAN PEREKAT UREA FORMALDEHIDA (The Properties of Particle Board from Oil Palm Empty Fruit Bunches Fiber Sawdust with Urea Formaldehyde Resin)

2016 ◽  
Vol 8 (1) ◽  
pp. 1
Author(s):  
Djoko Purwanto
Keyword(s):  
Bond Strength ◽  
Modulus Of Elasticity ◽  
Internal Bond ◽  
Urea Formaldehyde ◽  
Internal Bond Strength ◽  
Modulus Of Rupture ◽  
Particle Board ◽  
Palm Fiber ◽  
Empty Fruit Bunches ◽  
Screw Withdrawal

A palm oil mill with a capacity of hundred thousand tons of fresh fruit bunches per year will produce palm fiber waste about 12,000 tons. Recently, the use of palm empty fruit bunches (OPEFB) fiber is as fuel for electricity generation in the industry. Palm fiber waste contains lignocellulose materials as a feedstock to particle board manufacture. The aim of this research is to evaluate the properties of particle board from a mixture of OPEFB fiber and sawdust. The ratio of OPEFB fiber and sawdust are 100% : 0%; 75% : 25%; 50% : 50%; 25% : 75% and 0% : 100%, plus urea formaldehyde adhesive in a concentration of 11%. The boards were pressed using a clamp pressure of 16 kg/cm2 for 15 minutes at a temperature of 110 – 120 0C. The testing methods and standards of physical properties (moisture contents, thickness swelling, density) and mechanical (modulus of elasticity/MOE, modulus of rupture/MOR, screw withdrawal and internal bond strengths) refers to the SNI. 03 – 2105 - 2006. The results showed that the particle board made from 100% OPEFB fiber produces modulus of elasticity/MOE 1594.88 kg/cm2; modulus of rupture/MOR 18.08 kg/cm2; screw withdrawal 31.34 kg/cm2 and internal bond strength 0.86 kg/cm2. The addition of sawdust for 50% can improve modulus of elasticity/MOE, modulus of rupture/MOR and internal bond strength.

The influence of particleboard resination on their internal bond strength

2021 ◽  
Vol 115 ◽  
pp. 55-62
Author(s):  
Stella Rzyska-Pruchnik ◽  
Grzegorz Kowaluk
Keyword(s):  
Mechanical Property ◽  
Tensile Strength ◽  
Bond Strength ◽  
Physical Properties ◽  
Density Profile ◽  
Internal Bond ◽  
Internal Bond Strength ◽  
Modulus Of Rupture ◽  
Mechanical And Physical Properties ◽  
Positive Effect

The influence of particleboard resination on their internal bond strength. The aim of the project was to investigate the main mechanical and physical properties of particleboards, especially focused on internal bond, in terms of their resination. For the tests, the particleboards have been produced in laboratory conditions with the following glue content: 7, 10, 15, 30 and 50%. Particular attention was paid for examining the mechanical property – tensile strength perpendicular to surfaces (Internal Bond – IB). In addition, there were investigated modulus of elasticity (MOE), modulus of rupture (MOR) density and density profile. In the light of above mentioned tests, there is no positive effect of improvement of tested parameters when raise resination over 30% when producing particleboards. With the resination increase from 7 to 50% a significant change (densification) of panels’ structure, as well as differences between face and core layers density have been found.

Mechanical Properties of Homogenous and Heterogeneous Three Layered Particleboard Composite in Relation on Different Resin Content

2013 ◽  
Vol 699 ◽  
pp. 637-640 ◽  
Author(s):  
Siti Noorbaini Sarmin ◽  
Shaikh Abdul Karim Yamani Zakaria ◽  
Jamaludin Kasim
Keyword(s):  
Mechanical Properties ◽  
Bond Strength ◽  
Internal Bond ◽  
Bending Strength ◽  
Urea Formaldehyde ◽  
Acacia Mangium ◽  
Resin Content ◽  
Internal Bond Strength ◽  
Japanese Industrial Standard

Two types of three layered particleboard composite, homogeneous (Acacia mangium core-face/back) and heterogeneous (Acacia mangium core, mixed sawdust face/back) were fabricated with three different resin contents and densities. Three different resin content; 8:10:8, 10:10:10 and 12:10:12, were use with 500, 600 and 700kg/m3 board densities. Urea Formaldehyde (UF) was used as a binder and 1% of wax was added. The properties of bending strength (MOR & MOE) and internal bond strength (IB) were evaluated based on Japanese Industrial Standard; JIS A 5908:2003 Particleboard (2003). The results showed that there were relationship between resin contents and densities on homogeneous and heterogeneous particleboard composites. Result obtained indicated that bending and internal bond strength of homogeneous composite bonded using ratio of 12:10:12 resin content with 700kg/m3 density was better compared to ratio of 8:10:8 and 10:10:10 resin contents. When the densities were increased, the mechanical properties also increased.

scholarly journals Some of the Physical and Mechanical Properties of Particleboard Made from Betung Bamboo (Dendrocalamus asper)

2021 ◽  
Vol 11 (8) ◽  
pp. 3682
Author(s):  
Lina Karlinasari ◽  
Prabu Setia Sejati ◽  
Ulfa Adzkia ◽  
Arinana Arinana ◽  
Salim Hiziroglu
Keyword(s):  
Mechanical Properties ◽  
Bond Strength ◽  
Internal Bond ◽  
Fine Particles ◽  
Value Added ◽  
Physical And Mechanical Properties ◽  
Internal Bond Strength ◽  
Density Level ◽  
Coarse Particles ◽  
Dendrocalamus Asper

The objective of this study was to evaluate various physical and mechanical properties of experimental particleboard panels made from Asian giant bamboo (Dendrocalamus asper). Single layer panels having a density level of 0.75 g/cm3 from coarse and fine particles were used within the scope of this study. Thickness swelling, water absorption, surface roughness, and wettability characteristics of the samples were tested as physical properties while bending, internal bond strength, and screw withdrawal strength of the panels were considered for their mechanical properties. Resistance of the panels against termite and fungus were also determined. Based on the findings in the work both physical and mechanical properties of the panels made from coarse particles resulted in higher values than those made from fine particles with the exception of their internal bond strength. It appears that using fine particles in the panels enhanced their overall surface quality as well as wettability. Regarding biological deterioration of the samples, those made with coarse particles had better resistance. It seems that giant bamboo as a non-wood lignocellulosic species would have potential to be used as raw material to the manufacture value added particleboard with accepted characteristics.

scholarly journals Some advantages of three-layer medium-density fibreboard as compared to the traditional single-layer one

2019 ◽  
Vol 65 (1) ◽  
Author(s):  
Turgay Akbulut ◽  
Nadir Ayrilmis
Keyword(s):  
Bond Strength ◽  
Internal Bond ◽  
Single Layer ◽  
Middle Layer ◽  
Resin Content ◽  
Internal Bond Strength ◽  
Medium Density ◽  
Medium Density Fibreboard ◽  
Uf Resin ◽  
Layer Medium

Abstract The aim of the study was to develop three-layer medium-density fibreboard (MDF) manufacture by adding the coarse fibres in the middle layer, like three-layer particleboard. The liquid urea–formaldehyde (UF) resin was reduced from 10.5 to 6.5 wt% in the middle layer of the MDFs. The UF resin content was kept constant at 10 wt% in the surface layers of all the MDFs. Moreover, the average density of MDFs was decreased from 730 to 650 kg/m3. The internal bond strength of three-layer MDFs decreased with decreasing UF resin content (10.5 to 8.5 wt%) in the middle layer. However, the decreases in the internal bond strength were statistically not significant. The internal bond strength values of the MDFs having density between 730 and 675 kg/m3 did not show significant differences. The cost savings of the resin were 20% when the amount of resin was reduced from 10.5 to 8.5 wt%. Three-layer MDFs had lower resin consumption at lower densities over traditional single-layer MDFs produced in the same plant with the same material components without decreasing their technological properties. In conclusion, it can be said that three-layer MDF could be produced at a lower cost than traditional single-layer MDF.

scholarly journals Selected Properties of Overlaid Magnesium Based Composite Panels for Flooring

2020 ◽  
Vol 10 (15) ◽  
pp. 5028
Author(s):  
Fidan Aslanova ◽  
Gozen Elkiran ◽  
Salim Hiziroglu ◽  
Serkan Ilseven
Keyword(s):  
Bond Strength ◽  
Surface Quality ◽  
Internal Bond ◽  
Internal Bond Strength ◽  
Sample Type ◽  
Thickness Swelling ◽  
Mechanical And Physical Properties ◽  
Flooring Materials ◽  
Flooring Material

The objective of this work was to evaluate some of the mechanical and physical properties of the flooring materials manufactured from panels having magnesia substrate overlaid with oak veneer (Querqus alba) and linoleum sheets. Commercially manufactured panels were used in this work. Bending characteristics, internal bond strength, thickness swelling, and surface quality of the samples were evaluated. The highest modulus of elasticity (MOE) value of 4406 MPa for the sample type-A2 was loaded in the direction of the substrate followed by 3478 MPa for linoleum covered samples which were loaded in the same direction. Internal bond strength values of the panels did not show any significant differences from each other. Dimensional stability of the specimens in the form of thickness swelling for both 2-h and 24-h water soaking tests resulted in values ranging from 0.11 to 0.19%. The surface quality of the samples was not substantially influenced as a function of water exposure. Based on the results in this work magnesium substrate overlaid with oak veneer and linoleum panels could have potential to be used as flooring material with accepted properties.

Sign in / Sign up

Export Citation Format

Share Document