scholarly journals Characterization of the damping and mechanical properties of a novel (ZnSnO3/PVDF)@PPy nanofibers/EP composite

RSC Advances ◽  
2017 ◽  
Vol 7 (59) ◽  
pp. 37130-37138 ◽  
Author(s):  
Chunmei Zhang ◽  
Hua Li ◽  
Zhangzhi Zhuo ◽  
Roberto Dugnani ◽  
Wenchao Xue ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Epoxy Matrix ◽  
Lead Free ◽  
Piezoelectric Phase

Piezo-damping (ZnSnO3/PVDF)@PPy nanofibers/EP composites exhibit greatly improved damping and mechanical properties than epoxy matrix using lead-free self-poled ZnSnO3 as piezoelectric phase.

Behavior of composite advanced pore morphology foam

2011 ◽  
Vol 45 (26) ◽  
pp. 2823-2831 ◽  
Author(s):  
Matej Vesenjak ◽  
Franci Gačnik ◽  
Lovre Krstulović-Opara ◽  
Zoran Ren
Keyword(s):  
Mechanical Properties ◽  
Epoxy Matrix ◽  
Composite Structures ◽  
Mechanical Characterization ◽  
Experimental Testing ◽  
Compressive Loading ◽  
Metallic Foam ◽  
Pore Morphology ◽  
Computational Simulations

The mechanical characterization of advanced pore morphology (APM) foam, consisting of sphere-like metallic foam elements, is very limited since APM foam has been developed only recently. The purpose of this research was thus to determine the behavior of APM spheres and its composites when subjected to compressive loading. Single metallic APM spheres have been characterized with experimental testing and computational simulations, providing the basic properties and knowledge for an efficient composition of composite APM foam structures. Then, the APM foam elements were molded with epoxy matrix resulting in new composite structures. These composites have been adhered together with the epoxy resin achieving partial and syntactic morphology. The mechanical characterization of composite APM foam structures was based on experimental testing results with free and confined boundaries. The results of the performed research have shown valuable mechanical properties of the composite APM foam structures. Furthermore, they offer new possibilities for their use in general engineering applications.

Microstructural and fractographic characterization of B4C-Al cermets tested under dynamic and static loading

1989 ◽  
Vol 47 ◽  
pp. 562-563
Author(s):  
Gyeung Ho Kim ◽  
Mehmet Sarikaya ◽  
D. L. Milius ◽  
I. A. Aksay
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Static Loading ◽  
Carbon Deposition ◽  
Full Density ◽  
Unique Combination ◽  
Strong Component ◽  
Reaction Products

Cermets are designed to optimize the mechanical properties of ceramics (hard and strong component) and metals (ductile and tough component) into one system. However, the processing of such systems is a problem in obtaining fully dense composite without deleterious reaction products. In the lightweight (2.65 g/cc) B4C-Al cermet, many of the processing problems have been circumvented. It is now possible to process fully dense B4C-Al cermet with tailored microstructures and achieve unique combination of mechanical properties (fracture strength of over 600 MPa and fracture toughness of 12 MPa-m1/2). In this paper, microstructure and fractography of B4C-Al cermets, tested under dynamic and static loading conditions, are described.The cermet is prepared by infiltration of Al at 1150°C into partially sintered B4C compact under vacuum to full density. Fracture surface replicas were prepared by using cellulose acetate and thin-film carbon deposition. Samples were observed with a Philips 3000 at 100 kV.

Characterization of interfaces in CVD-coated nicalon fiber-reinforced SiC

1989 ◽  
Vol 47 ◽  
pp. 556-557
Author(s):  
K.L. More ◽  
R.A. Lowden
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Chemical Vapor ◽  
Chemical Vapor Infiltration ◽  
Frictional Stress ◽  
Fiber Reinforced ◽  
Pull Out ◽  
Carbon Coated ◽  
Fiber Matrix

The mechanical properties of fiber-reinforced composites are directly related to the nature of the fiber-matrix bond. Fracture toughness is improved when debonding, crack deflection, and fiber pull-out occur which in turn depend on a weak interfacial bond. The interfacial characteristics of fiber-reinforced ceramics can be altered by applying thin coatings to the fibers prior to composite fabrication. In a previous study, Lowden and co-workers coated Nicalon fibers (Nippon Carbon Company) with silicon and carbon prior to chemical vapor infiltration with SiC and determined the influence of interfacial frictional stress on fracture phenomena. They found that the silicon-coated Nicalon fiber-reinforced SiC had low flexure strengths and brittle fracture whereas the composites containing carbon coated fibers exhibited improved strength and fracture toughness. In this study, coatings of boron or BN were applied to Nicalon fibers via chemical vapor deposition (CVD) and the fibers were subsequently incorporated in a SiC matrix. The fiber-matrix interfaces were characterized using transmission and scanning electron microscopy (TEM and SEM). Mechanical properties were determined and compared to those obtained for uncoated Nicalon fiber-reinforced SiC.

Effect of aluminum content on structure, transport and mechanical properties of Sn-Zn eutectic lead free solder alloy rapidly solidified from melt.

2015 ◽  
Vol 10 (1) ◽  
pp. 2641-2648
Author(s):  
Rizk Mostafa Shalaby ◽  
Mohamed Munther ◽  
Abu-Bakr Al-Bidawi ◽  
Mustafa Kamal
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Lead Free ◽  
Al Alloy ◽  
Lead Free Solder ◽  
Pronounced Increase ◽  
Mass Unit ◽  
Size Refinement ◽  
Free Solder ◽  
Lead Free Solders

The greatest advantage of Sn-Zn eutectic is its low melting point (198 oC) which is close to the melting point. of Sn-Pb eutectic solder (183 oC), as well as its low price per mass unit compared with Sn-Ag and Sn-Ag-Cu solders. In this paper, the effect of 0.0, 1.0, 2.0, 3.0, 4.0, and 5.0 wt. % Al as ternary additions on melting temperature, microstructure, microhardness and mechanical properties of the Sn-9Zn lead-free solders were investigated. It is shown that the alloying additions of Al at 4 wt. % to the Sn-Zn binary system lead to lower of the melting point to 195.72 ˚C.  From x-ray diffraction analysis, an aluminium phase, designated α-Al is detected for 4 and 5 wt. % Al compositions. The formation of an aluminium phase causes a pronounced increase in the electrical resistivity and microhardness. The ternary Sn-9Zn-2 wt.%Al exhibits micro hardness superior to Sn-9Zn binary alloy. The better Vickers hardness and melting points of the ternary alloy is attributed to solid solution effect, grain size refinement and precipitation of Al and Zn in the Sn matrix.  The Sn-9%Zn-4%Al alloy is a lead-free solder designed for possible drop-in replacement of Pb-Sn solders.  

PREPARATION AND CHARACTERIZATION OF REPROCESSED COMPOSITES OF POLYPROPYLENE REINFORCED BY WOOD FIBERS: PHYSICAL AND MECHANICAL PROPERTIES

2017 ◽  
Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Fibers
Sign in / Sign up

Export Citation Format

Share Document