scholarly journals Evaluation and Simulation on the Reserve Capacity of Thermal Storage Electric Boiler Clusters

2020 ◽  
Vol 143 ◽  
pp. 02013
Author(s):  
Linjun Cai ◽  
Zheng Zhang ◽  
Dongliang Xie ◽  
Xiaofang Song ◽  
Yening Lai
Keyword(s):  
Renewable Energy ◽  
Storage Tank ◽  
Evaluation Method ◽  
Heat Storage ◽  
Power Grid ◽  
Renewable Energy Sources ◽  
Thermal Storage ◽  
Reserve Capacity ◽  
Peak Shaving ◽  
Electric Boiler

After providing a better service for nearby heating loads, a thermal storage electric boiler system can use the heat storage tank to participate in the peak-shaving and reserve services of the power grid. Current researches focus on its peak-shaving capacity, but ignores the use of its reserve capacity, which is important to the random fluctuations of renewable energy sources. Facing the actual analyzing demands on power system adequacy, this paper starts with the discussion of typical operation modes, and builds the powersystem- adequacy model of a thermal-storage electric boiler based heating system. Based on the presented model, the concept of feasible domain for heat charging and discharging is proposed. By implementing the concept, the quantitative evaluation method to calculate the reserve capacity of a thermal storage electric boiler system is proposed. The verification of the method is also given. Based on the planning data of an actual power grid, the short-term reserve capacity as well as the effect on promoting renewable energy consumption is estimated according to the given size of the provincial thermal storage electric boiler clusters. Finally, the influences of different choices of peak-shaving strategies, heat storage tank capacity on its reserve capacity are simulated and analyzed.

scholarly journals Analysis of renewable energy sources and a heat storage tank application in a district heating substation

2021 ◽  
Vol 323 ◽  
pp. 00006
Author(s):  
Kamil Chłosta ◽  
Wiesław Zima
Keyword(s):  
Renewable Energy ◽  
Storage Tank ◽  
Heat Storage ◽  
Renewable Energy Sources ◽  
District Heating ◽  
Operating Conditions ◽  
Energy Sources ◽  
Heat Sources ◽  
Water Parameters ◽  
Air Source Heat Pump

The study verifies the potential application of renewable energy sources in a district heating substation. Different operating configurations of heat sources have been analysed, including solar collectors, PV panels and air source heat pump. Concepts of regulating the water parameters in a substation have been analysed. Moreover, the potential impact of a heat storage tank application has been calculated using a genetic algorithm to find optimal operating conditions in a district heating substation. The analysis is based on measured yearly data.

scholarly journals Voltage Stability of Power Systems with Renewable-Energy Inverter-Based Generators: A Review

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 115
Author(s):  
Nasser Hosseinzadeh ◽  
Asma Aziz ◽  
Apel Mahmud ◽  
Ameen Gargoom ◽  
Mahbub Rabbani
Keyword(s):  
Renewable Energy ◽  
Power Systems ◽  
Voltage Stability ◽  
Reactive Power ◽  
Power Grid ◽  
Renewable Energy Sources ◽  
Electrical Power ◽  
System Stability ◽  
Special Issue ◽  
Synchronous Generators

The main purpose of developing microgrids (MGs) is to facilitate the integration of renewable energy sources (RESs) into the power grid. RESs are normally connected to the grid via power electronic inverters. As various types of RESs are increasingly being connected to the electrical power grid, power systems of the near future will have more inverter-based generators (IBGs) instead of synchronous machines. Since IBGs have significant differences in their characteristics compared to synchronous generators (SGs), particularly concerning their inertia and capability to provide reactive power, their impacts on the system dynamics are different compared to SGs. In particular, system stability analysis will require new approaches. As such, research is currently being conducted on the stability of power systems with the inclusion of IBGs. This review article is intended to be a preface to the Special Issue on Voltage Stability of Microgrids in Power Systems. It presents a comprehensive review of the literature on voltage stability of power systems with a relatively high percentage of IBGs in the generation mix of the system. As the research is developing rapidly in this field, it is understood that by the time that this article is published, and further in the future, there will be many more new developments in this area. Certainly, other articles in this special issue will highlight some other important aspects of the voltage stability of microgrids.

scholarly journals Estimation of Energy Activity and Flexibility Range in Smart Active Residential Building

Smart Cities ◽  
2019 ◽  
Vol 2 (4) ◽  
pp. 471-495
Author(s):  
Viktor Stepaniuk ◽  
Jayakrishnan Pillai ◽  
Birgitte Bak-Jensen ◽  
Sanjeevikumar Padmanaban
Keyword(s):  
Renewable Energy ◽  
Energy Management ◽  
Storage Tank ◽  
Residential Buildings ◽  
Renewable Energy Sources ◽  
Hot Water ◽  
Active Management ◽  
Worst Case ◽  
And Storage ◽  
Storage Units

The smart active residential buildings play a vital role to realize intelligent energy systems by harnessing energy flexibility from loads and storage units. This is imperative to integrate higher proportions of variable renewable energy generation and implement economically attractive demand-side participation schemes. The purpose of this paper is to develop an energy management scheme for smart sustainable buildings and analyze its efficacy when subjected to variable generation, energy storage management, and flexible demand control. This work estimate the flexibility range that can be reached utilizing deferrable/controllable energy system units such as heat pump (HP) in combination with on-site renewable energy sources (RESs), namely photovoltaic (PV) panels and wind turbine (WT), and in-house thermal and electric energy storages, namely hot water storage tank (HWST) and electric battery as back up units. A detailed HP model in combination with the storage tank is developed that accounts for thermal comforts and requirements, and defrost mode. Data analytics is applied to generate demand and generation profiles, and a hybrid energy management and a HP control algorithm is developed in this work. This is to integrate all active components of a building within a single complex-set of energy management solution to be able to apply demand response (DR) signals, as well as to execute all necessary computation and evaluation. Different capacity scenarios of the HWST and battery are used to prioritize the maximum use of renewable energy and consumer comfort preferences. A flexibility range of 22.3% is achieved for the scenario with the largest HWST considered without a battery, while 10.1% in the worst-case scenario with the smallest HWST considered and the largest battery. The results show that the active management and scheduling scheme developed to combine and prioritize thermal, electrical and storage units in buildings is essential to be studied to demonstrate the adequacy of sustainable energy buildings.

Volume Sizing for Thermal Storage With Phase Change Material for Concentrated Solar Power Plant

2014 ◽  
Author(s):  
Ben Xu ◽  
Peiwen Li ◽  
Cholik Chan
Keyword(s):  
Power Plant ◽  
Phase Change ◽  
Phase Change Material ◽  
Storage Tank ◽  
Solar Power ◽  
Heat Storage ◽  
Storage System ◽  
Thermal Storage ◽  
Concentrated Solar Power ◽  
Change Material

With a large capacity thermal storage system using phase change material (PCM), Concentrated Solar Power (CSP) is a promising technology for high efficiency of solar energy utilization. In a thermal storage system, a dual-media thermal storage tank is typically adopted in industry for the purpose of reducing the use of the heat transfer fluid (HTF). While the dual-media sensible heat storage system has been well studied, a dual-media latent heat storage system (LHSS) still needs more attention and study; particularly, the sizing of volumes of storage tanks considering actual operation conditions is of significance. In this paper, a strategy for LHSS volume sizing is proposed, which is based on computations using an enthalpy-based 1D model. One example of 60MW solar thermal power plant with 35% thermal efficiency is presented. In the study, potassium hydroxide (KOH) is adopted as PCM and Therminol VP-1 is used as HTF. The operational temperatures of the storage system are 390°C and 310°C, respectively for the high and low temperatures. The system is assumed to operate for 100 days with 6 hours charge and 6 hours discharge every day. From the study, the needed height of the thermal storage tank is calculated from using the strategy of tank sizing. The method for tank volume sizing is of significance to engineering application.

Energy Storage Start-up Strategies for Concentrated Solar Power Plants With a Dual-Media Thermal Storage System

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Ben Xu ◽  
Peiwen Li ◽  
Cho Lik Chan
Keyword(s):  
Energy Storage ◽  
Storage Tank ◽  
Heat Storage ◽  
Storage System ◽  
Electrical Energy ◽  
Thermal Storage ◽  
Energy Output ◽  
Concentrated Solar Power ◽  
Start Up ◽  
Hot Start

A concentrated solar power (CSP) plant typically has thermal energy storage (TES), which offers advantages of extended operation and power dispatch. Using dual-media, TES can be cost-effective because of the reduced use of heat transfer fluid (HTF), usually an expensive material. The focus of this paper is on the effect of a start-up period thermal storage strategy to the cumulative electrical energy output of a CSP plant. Two strategies—starting with a cold storage tank (referred to as “cold start”) and starting with a fully charged storage tank (referred to as “hot start”)—were investigated with regards to their effects on electrical energy production in the same period of operation. An enthalpy-based 1D transient model for energy storage and temperature variation in solid filler material and HTF was applied for both the sensible heat storage system (SHSS) and the latent heat storage system (LHSS). The analysis was conducted for a CSP plant with an electrical power output of 60 MWe. It was found that the cold start is beneficial for both the SHSS and LHSS systems due to the overall larger electrical energy output over the same number of days compared to that of the hot start. The results are expected to be helpful for planning the start-up operation of a CSP plant with a dual-media thermal storage system.

Sign in / Sign up

Export Citation Format

Share Document