APPLICATION OF FERROELECTRIC MATERIALS IN ELECTRICAL FILTERS

1972 ◽  
Vol 33 (C2) ◽  
pp. C2-33-C2-37
Author(s):  
M. de JONG
Author(s):  
Naoki Yamamoto ◽  
Makoto Kikuchi ◽  
Tooru Atake ◽  
Akihiro Hamano ◽  
Yasutoshi Saito

BaZnGeO4 undergoes many phase transitions from I to V phase. The highest temperature phase I has a BaAl2O4 type structure with a hexagonal lattice. Recent X-ray diffraction study showed that the incommensurate (IC) lattice modulation appears along the c axis in the III and IV phases with a period of about 4c, and a commensurate (C) phase with a modulated period of 4c exists between the III and IV phases in the narrow temperature region (—58°C to —47°C on cooling), called the III' phase. The modulations in the IC phases are considered displacive type, but the detailed structures have not been studied. It is also not clear whether the modulation changes into periodic arrays of discommensurations (DC’s) near the III-III' and IV-V phase transition temperature as found in the ferroelectric materials such as Rb2ZnCl4.At room temperature (III phase) satellite reflections were seen around the fundamental reflections in a diffraction pattern (Fig.1) and they aligned along a certain direction deviated from the c* direction, which indicates that the modulation wave vector q tilts from the c* axis. The tilt angle is about 2 degree at room temperature and depends on temperature.


Author(s):  
V. Saikumar ◽  
H. M. Chan ◽  
M. P. Harmer

In recent years, there has been a growing interest in the application of ferroelectric thin films for nonvolatile memory applications and as a gate insulator in DRAM structures. In addition, bulk ferroelectric materials are also widely used as components in electronic circuits and find numerous applications in sensors and actuators. To a large extent, the performance of ferroelectric materials are governed by the ferroelectric domains (with dimensions in the micron to sub-micron range) and the switching of domains in the presence of an applied field. Conventional TEM studies of ferroelectric domains structures, in conjunction with in-situ studies of the domain interactions can aid in explaining the behavior of ferroelectric materials, while providing some answers to the mechanisms and processes that influence the performance of ferroelectric materials. A few examples from bulk and thin film ferroelectric materials studied using the TEM are discussed below.Figure 1 shows micrographs of ferroelectric domains obtained from undoped and Fe-doped BaTiO3 single crystals. The domain boundaries have been identified as 90° domains with the boundaries parallel to <011>.


Author(s):  
Wenwu Cao

Domain structures play a key role in determining the physical properties of ferroelectric materials. The formation of these ferroelectric domains and domain walls are determined by the intrinsic nonlinearity and the nonlocal coupling of the polarization. Analogous to soliton excitations, domain walls can have high mobility when the domain wall energy is high. The domain wall can be describes by a continuum theory owning to the long range nature of the dipole-dipole interactions in ferroelectrics. The simplest form for the Landau energy is the so called ϕ model which can be used to describe a second order phase transition from a cubic prototype,where Pi (i =1, 2, 3) are the components of polarization vector, α's are the linear and nonlinear dielectric constants. In order to take into account the nonlocal coupling, a gradient energy should be included, for cubic symmetry the gradient energy is given by,


Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 221
Author(s):  
Mariya Aleksandrova ◽  
Ivailo Pandiev

This paper presents impedance measurements of ferroelectric structures involving lead-free oxide and polymer-oxide composite coatings for sensing and energy harvesting applications. Three different ferroelectric materials grown by conventional microfabrication technologies on solid or flexible substrates are investigated for their basic resonant characteristics. Equivalent electrical circuit models are applied to all cases to explain the electrical behavior of the structures, according to the materials type and thickness. The analytical results show good agreement with the experiments carried out on a basic types of excited thin-film piezoelectric transducers. Additionally, temperature and frequency dependences of the dielectric permittivity and losses are measured for the polymer-oxide composite device in relation with the surface morphology before and after introduction of the polymer to the functional film.


Sign in / Sign up

Export Citation Format

Share Document