KINETICS OF α'-MARTENSITE FORMATION DURING FATIGUE DEFORMATION IN METASTABLE AUSTENITIC STAINLESS STEEL

1982 ◽  
Vol 43 (C4) ◽  
pp. C4-423-C4-428 ◽  
Author(s):  
K. Tsuzaki ◽  
T. Maki ◽  
I. Tamura
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Martensite Formation ◽  
Metastable Austenitic Stainless Steel ◽  
Fatigue Deformation ◽  
Kinetics Of

A TEM microscopical investigation of the magnetic domain structure of a metastable austenitic stainless steel

1994 ◽  
Vol 52 ◽  
pp. 696-697
Author(s):  
G. Fourlaris ◽  
T. Gladman
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Cold Rolling ◽  
Solution Treatment ◽  
Magnetic Domain ◽  
High Strength ◽  
Medium Carbon Steel ◽  
Magnetic Characteristics ◽  
Metastable Austenitic Stainless Steel

Stainless steels have widespread applications due to their good corrosion resistance, but for certain types of large naval constructions, other requirements are imposed such as high strength and toughness , and modified magnetic characteristics.The magnetic characteristics of a 302 type metastable austenitic stainless steel has been assessed after various cold rolling treatments designed to increase strength by strain inducement of martensite. A grade 817M40 low alloy medium carbon steel was used as a reference material.The metastable austenitic stainless steel after solution treatment possesses a fully austenitic microstructure. However its tensile strength , in the solution treated condition , is low.Cold rolling results in the strain induced transformation to α’- martensite in austenitic matrix and enhances the tensile strength. However , α’-martensite is ferromagnetic , and its introduction to an otherwise fully paramagnetic matrix alters the magnetic response of the material. An example of the mixed martensitic-retained austenitic microstructure obtained after the cold rolling experiment is provided in the SEM micrograph of Figure 1.

Effects of Deformation Mode on Resistivity Curve Used for Estimating Martensite Induced in Stainless Steel

2010 ◽  
Vol 638-642 ◽  
pp. 2992-2997 ◽  
Author(s):  
Hidefumi Date
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Linear Relation ◽  
Volume Fraction ◽  
Tensile Deformation ◽  
Deformation Mode ◽  
Transformation Process ◽  
Martensite Formation ◽  
Austenitic Phase ◽  
Ε Phase

The martensite induced in three types of austenitic stainless steel, which indicate the different stability of the austenitic phase (γ), were estimated by the resistivity measured during the tensile deformation or compressive deformation at the temperatures 77, 187 and 293 K. The resistivity curves were strongly dependent on the deformation mode. The volume fraction of the martensite (α’) was also affected by the deformation mode. The ε phase, which is the precursor of the martensite and is induced from the commencement of the deformation, decreased the resistivity. However, lots of defects generated by the deformation-induced martensite increased the resistivity. The experimental facts and the results shown by the modified parallelepiped model suggested a complicated transformation process depending on each deformation mode. The results shown by the model also suggested a linear relation between the resistivity and the martensite volume at the region of the martensite formation. The fact denoted that the resistivity is mostly not controlled by the austenite, ε phase and martensite, but by the defects induced due to the deformation-induced martensite.

Sign in / Sign up

Export Citation Format

Share Document