Characterization of mechanical properties of metallic foams by instrumented indentation test

2018 ◽  
Vol 115 (4) ◽  
pp. 405
Author(s):  
Ali Nayebi ◽  
Azam Surmiri
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Constitutive Model ◽  
Indentation Test ◽  
Metallic Foam ◽  
Spherical Indentation ◽  
Metallic Foams ◽  
Aluminum Foams ◽  
Inelastic Behaviour ◽  
Indentation Response

In this study, the spherical indentation tests with a spherical rigid indenter of 5 mm radius were used. The inelastic behaviour of metallic foam was considered as an isotropic crushable foam constitutive model of Deshpande and Fleck which has been shown experimentally that their model can be applied to aluminum foams. The spherical indentation test was modeled by finite element method. A 2D axisymmetric model was developed. Practically, the size of the indenter tip should be reasonably large compared to the size of the cells/pores in the specimen and the indentation depth should also be reasonably large so that the indentation response does reflect the averaged material behaviours, which are described by the aforementioned constitutive model. The applied load on the indenter versus its displacement was obtained under different metallic foam mechanical properties. Numerical results from the finite element simulations are used to obtain the dependence of the indentation response on the metallic foam material parameters which characterizes the plastic deformation of metallic foams. Finally, the stress–curves and the elastic modulus of different foams are obtained by the indentation curve, which is obtained by FEM.

Effect of Nonlinear Kinematic Hardening Constants on Cyclic Spherical Indentation Test

2010 ◽  
Author(s):  
A. Nayebi
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Applied Load ◽  
Kinematic Hardening ◽  
Hysteresis Loops ◽  
Indentation Test ◽  
Material Behavior ◽  
Spherical Indentation ◽  
Displacement Curve ◽  
Residual Displacements

In the last decade, instrumented indentation test has been widely used to determine the mechanical properties of different materials and especially for metals. The mechanical properties such as Young modulus, yield stress, hardening exponent, and stress-strain curve were determined with the help of the load–displacement curve of the continuous indentation test. The method consists of pushing an indenter in a material sample and the applied load and the indenter displacement are measured. In this research the load on the indenter was considered as cyclic and varied from zero to Fmax. Because of the Bauschinger effect, the hysteresis loops were formed. With the help of these hysteresis loops, nonlinear kinematic hardening parameters of the Armstrong–Freiderick (A-F) model can be determined. Spherical indenter was used and the sample was considered isotropic. The material behavior was modeled by the A-F rule. The test was modeled by the finite element method. An axi-symmetric mesh was used. The A–F model constants, C and γ, were varied to obtain their effects on the hysteresis loops. Maximum applied load was considered constant for different finite element modeling and the maximum and residual displacements were calculated from the simulations results. The normalized maximum and the residual displacements were increased as a function of the cycles. It was shown that these parameters value and their rate are dependent on the material model constants. These dependences were shown for different examples which can help to characterize the A-F model constants by the cyclic spherical indentation tests.

Determination of mechanical properties from sharp dynamic indentation

2021 ◽  
pp. 030932472110592
Author(s):  
Bowen Si ◽  
Zhiqiang Li ◽  
Gesheng Xiao ◽  
Xuefeng Shu
Keyword(s):  
Mechanical Properties ◽  
Power Law ◽  
Split Hopkinson Pressure Bar ◽  
Indentation Test ◽  
Hopkinson Pressure Bar ◽  
Dynamic Indentation ◽  
Material Parameters ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Indentation Response

In this study, a dynamic indentation test method based on the split Hopkinson pressure bar is proposed to obtain the dynamic parameters of Ludwik power law constitutive, namely, Young’s modulus E, strength coefficient K, and strain hardening index n by analyzing dynamic indentation load-indentation depth curve obtained from the theories relating to the Hopkinson pressure bar. The important parameters, namely, loading curvature C and transformation factor [Formula: see text], are invoked to examine the dynamic indentation response results in a wide range of target material parameters. Finite element calculation results are processed through simulation of dynamic indentation response with broad material parameters. Furthermore, the analytical method is used to fit simulation results to obtain the analytical equations for elastic–plastic parameters and curvature parameters for the subsequent analysis. The analytical equation of forward model to predict dynamic indentation response parameter–loading curvature C of a known material is proposed. Then, the elastic–plastic parameters of unknown materials (according to Ludwik power law) are obtained by substituting the dynamic indentation response parameters into an inverse analytical equation under the two types of half-cone angle indenters. The method is verified by other typical materials, which shows that the dynamic indentation test based on the split Hopkinson pressure bar can obtain sufficient conditions to obtain dynamic mechanical properties of target materials.

Effect of Crystallographic Orientation on Nanoindentation Response of Fe3Si Single-Crystals

2018 ◽  
Vol 784 ◽  
pp. 44-48 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Aleš Materna
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Shear Stress ◽  
Contact Area ◽  
Measured Data ◽  
Deformation Mechanisms ◽  
Spherical Indentation ◽  
Indentation Modulus ◽  
Slip Systems ◽  
Correct Interpretation

Deformation mechanisms and mechanical properties of Fe3(wt.%)Si single crystal in two different orientations were investigated by spherical indentation. For correct interpretation of measured data and better understanding of the deformation mechanisms under the contact area, finite element simulations were carried out and resolved shear stress in available slip systems was computed. Pop-in behavior, differences in hardness, indentation modulus and shapes of residual imprints were observed and associated with different activation of slip.

scholarly journals Finite Element Analysis of the Nanomechanics of Hard Coatings on a Soft Polymer Substrate by a Spherical Indenter

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Chunlai Tian ◽  
Pengfei Duan
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Viscoelastic Model ◽  
Coating System ◽  
Element Analysis ◽  
Soft Polymer ◽  
Indentation Response

Composite has been widely used in various fields due to its advanced performance. To reveal the relation between the mechanical properties of the composite and that of each individual component, finite element analysis (FEA) has usually been adopted. In this study, in order to predict the mechanical properties of hard coating on a soft polymer, the response of this coating system during nanoindentation was modelled. Various models, such as a viscoelastic model and fitting model, were adopted to analyse the indentation response of this coating system. By varying the substrate properties (i.e., Young’s modulus, viscoelasticity, and Poisson’s ratio), Young’s modulus, energy loss, and the viscoelastic model of the coating system were analysed, and how the mechanical properties of the substrate will affect the indentation response of the coating system was discussed.

Modeling of the Behavior of an Aluminum Metallic Foam by Both FEM and Experimental Results

2013 ◽  
Vol 773-774 ◽  
pp. 478-487
Author(s):  
Juan Pablo Fuertes ◽  
Rodrigo Luri ◽  
Javier León ◽  
Daniel Salcedo ◽  
Ignacio Puertas ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flow Stress ◽  
Material Flow ◽  
Aluminum Foam ◽  
Research Work ◽  
Physical And Mechanical Properties ◽  
Metallic Foam ◽  
Low Density ◽  
Metallic Materials ◽  
Aluminum Foams

Aluminum foams are porous metallic materials which possess an outstanding combination of physical and mechanical properties such as: a high rigidity with a very low density. In this present research work, a study on the upsetting of an aluminum foam (with a density = 0.73 g/cm3) is carried out by employing different compression velocity values. From the results obtained, it is possible to determine the material flow stress for its subsequent use in finite element simulations (FEM). Once the material flow stress has been determined, it will be employed in order to analyze the conformability of several parts by FEM.

Sign in / Sign up

Export Citation Format

Share Document