scholarly journals Sensor, Signal and Image Informatics

2006 ◽  
Vol 15 (01) ◽  
pp. 57-67 ◽  
Author(s):  
T. Aach ◽  
H. Witte ◽  
T.M. Lehmann
Keyword(s):  
Data Acquisition ◽  
Signal Analysis ◽  
Emission Computed Tomography ◽  
Biomedical Data ◽  
Data Handling ◽  
Sensor Signal ◽  
Biomedical Signal ◽  
Time Frequency ◽  
Image Informatics ◽  
Recent Trends

SummaryThe number of articles published annually in the fields of biomedical signal and image acquisition and processing is increasing. Based on selected examples, this survey aims at comprehensively demonstrating the recent trends and developments.Four articles are selected for biomedical data acquisition covering topics such as dose saving in CT, C-arm X-ray imaging systems for volume imaging, and the replacement of dose-intensive CTbased diagnostic with harmonic ultrasound imaging. Regarding biomedical signal analysis (BSA), the four selected articles discuss the equivalence of different time-frequency approaches for signal analysis, an application to Cochlea implants, where time-frequency analysis is applied for controlling the replacement system, recent trends for fusion of different modalities, and the role of BSA as part of a brain machine interfaces. To cover the broad spectrum of publications in the field of biomedical image processing, six papers are focused. Important topics are content-based image retrieval in medical applications, automatic classification of tongue photographs from traditional Chinese medicine, brain perfusion analysis in single photon emission computed tomography (SPECT), model-based visualization of vascular trees, and virtual surgery, where enhanced visualization and haptic feedback techniques are combined with a sphere-filled model of the organ.The selected papers emphasize the five fields forming the chain of biomedical data processing: (1) data acquisition, (2) data reconstruction and pre-processing, (3) data handling, (4) data analysis, and (5) data visualization. Fields 1 and 2 form the sensor informatics, while fields 2 to 5 form signal or image informatics with respect to the nature of the data considered.Biomedical data acquisition and pre-processing, as well as data handling, analysis and visualization aims at providing reliable tools for decision support that improve the quality of health care. Comprehensive evaluation of the processing methods and their reliable integration in routine applications are future challenges in the field of sensor, signal and image informatics.

scholarly journals Discussion of “Time-frequency Techniques in Biomedical Signal Analysis: A Tutorial Review of Similarities and Differences”

2013 ◽  
Vol 52 (04) ◽  
pp. 297-307 ◽  
Author(s):  
C. Baumgartner ◽  
K. J. Blinowska ◽  
A. Cichocki ◽  
H. Dickhaus ◽  
P. J. Durka ◽  
...  
Keyword(s):  
Signal Analysis ◽  
Biomedical Signal ◽  
Time Frequency ◽  
Biomedical Signal Analysis ◽  
Similarities And Differences

A Fault Detection Approach Based on Sound Signal Analysis for Equipment Monitoring

2020 ◽  
pp. 129-139
Author(s):  
Weihai Sun ◽  
Lemei Han
Keyword(s):  
Fault Detection ◽  
Signal Analysis ◽  
Energy Analysis ◽  
Detection Method ◽  
Sound Signal ◽  
Practical Significance ◽  
Time Frequency ◽  
Detection Approach ◽  
Machine Fault ◽  
Learning Data

Machine fault detection has great practical significance. Compared with the detection method that requires external sensors, the detection of machine fault by sound signal does not need to destroy its structure. The current popular audio-based fault detection often needs a lot of learning data and complex learning process, and needs the support of known fault database. The fault detection method based on audio proposed in this paper only needs to ensure that the machine works normally in the first second. Through the correlation coefficient calculation, energy analysis, EMD and other methods to carry out time-frequency analysis of the subsequent collected sound signals, we can detect whether the machine has fault.

Extending Acoustic Microscopy for Comprehensive Failure Analysis Applications

2010 ◽  
Author(s):  
Sebastian Brand ◽  
Matthias Petzold ◽  
Peter Czurratis ◽  
Peter Hoffrogge
Keyword(s):  
Image Processing ◽  
Failure Analysis ◽  
Signal Analysis ◽  
Flip Chip ◽  
Fault Isolation ◽  
Acoustic Microscopy ◽  
Specific Information ◽  
Full Potential ◽  
Time Frequency ◽  
Non Destructive

Abstract In industrial manufacturing of microelectronic components, non-destructive failure analysis methods are required for either quality control or for providing a rapid fault isolation and defect localization prior to detailed investigations requiring target preparation. Scanning acoustic microscopy (SAM) is a powerful tool enabling the inspection of internal structures in optically opaque materials non-destructively. In addition, depth specific information can be employed for two- and three-dimensional internal imaging without the need of time consuming tomographic scan procedures. The resolution achievable by acoustic microscopy is depending on parameters of both the test equipment and the sample under investigation. However, if applying acoustic microscopy for pure intensity imaging most of its potential remains unused. The aim of the current work was the development of a comprehensive analysis toolbox for extending the application of SAM by employing its full potential. Thus, typical case examples representing different fields of application were considered ranging from high density interconnect flip-chip devices over wafer-bonded components to solder tape connectors of a photovoltaic (PV) solar panel. The progress achieved during this work can be split into three categories: Signal Analysis and Parametric Imaging (SA-PI), Signal Analysis and Defect Evaluation (SA-DE) and Image Processing and Resolution Enhancement (IP-RE). Data acquisition was performed using a commercially available scanning acoustic microscope equipped with several ultrasonic transducers covering the frequency range from 15 MHz to 175 MHz. The acoustic data recorded were subjected to sophisticated algorithms operating in time-, frequency- and spatial domain for performing signal- and image analysis. In all three of the presented applications acoustic microscopy combined with signal- and image processing algorithms proved to be a powerful tool for non-destructive inspection.

Three-Point Bending Test Evaluation of Concrete Specimens by Non-Traditional Analysis of Acoustic Emission Method

2016 ◽  
Vol 837 ◽  
pp. 198-202
Author(s):  
Luboš Pazdera ◽  
Libor Topolář ◽  
Tomáš Vymazal ◽  
Petr Daněk ◽  
Jaroslav Smutny
Keyword(s):  
Acoustic Emission ◽  
Signal Analysis ◽  
Measurement Data ◽  
Bending Test ◽  
Test Evaluation ◽  
Acoustic Emission Method ◽  
Emission Method ◽  
Three Point Bending ◽  
Time Frequency ◽  
Emission Signal

The aim of the paper is focused on the analysis of the mechanical properties of the concrete specimens with plasticizer at three point bending test by the signal analysis of the acoustic emission signal. The evaluations were compared the measurement and the results obtained with theoretical presumptions. The Joint Time Frequency Analysis applied on measurement data and its evaluation is described. It is well known that the Acoustic Emission Method is a very sensitive method to determine active cracks into structure. However, evaluation of acoustic emission signals is very difficult. A non-traditional method was used to signal analysis of burst acoustic emission signals recorded during three point bending test.

Quality Monitoring System for Seismic While Drilling

2013 ◽  
Vol 318 ◽  
pp. 572-575
Author(s):  
Li Li Yu ◽  
Yu Hong Li ◽  
Ai Feng Wang
Keyword(s):  
Data Acquisition ◽  
Monitoring System ◽  
Signal Analysis ◽  
Quality Evaluation ◽  
Quality Monitoring ◽  
Quality Of Data ◽  
Whole Process ◽  
Engineering Parameters ◽  
Network Status

In this paper a quality monitoring system for seismic while drilling (SWD) that integrates the whole process of data acquisition was developed. The acquisition equipment, network status and signals of accelerometer and geophone were monitored real-time. With fast signal analysis and quality evaluation, the acquisition parameters and drilling engineering parameters can be adjusted timely. The application of the system can improve the quality of data acquisition and provide subsequent processing and interpretation with high qualified reliable data.

A Modified S-Transform for EEG Signals Analysis

2015 ◽  
Vol 12 (03) ◽  
pp. 1550021 ◽  
Author(s):  
M. A. Al-Manie ◽  
W. J. Wang
Keyword(s):  
Image Processing ◽  
Fourier Transform ◽  
Energy Concentration ◽  
Biomedical Data ◽  
Short Time Fourier Transform ◽  
Phase Information ◽  
Eeg Signals ◽  
Time Frequency ◽  
S Transform ◽  
Short Time

Due to the advantages offered by the S-transform (ST) distribution, it has been recently successfully implemented for various applications such as seismic and image processing. The desirable properties of the ST include a globally referenced phase as the case with the short time Fourier transform (STFT) while offering a higher spectral resolution as the wavelet transform (WT). However, this estimator suffers from some inherent disadvantages seen as poor energy concentration with higher frequencies. In order to improve the performance of the distribution, a modification to the existing technique is proposed. Additional parameters are proposed to control the window's width which can greatly enhance the signal representation in the time–frequency plane. The new estimator's performance is evaluated using synthetic signals as well as biomedical data. The required features of the ST which include invertability and phase information are still preserved.

Sign in / Sign up

Export Citation Format

Share Document