SUB-SURFACE UNCERTAINTY IN OIL FIELDS: LEARNINGS FROM EARLY PRODUCTION OF LEGENDRE OIL FIELDS

2003 ◽  
Vol 43 (1) ◽  
pp. 401
Author(s):  
R. Seggie ◽  
F. Jamal ◽  
A. Jones ◽  
M. Lennane ◽  
G. McFadzean ◽  
...  

The Legendre North and South Oil Fields (together referred to as the field) have been producing since May 2001 from high rate horizontal wells and had produced 18 MMBBL by end 2002. This represents about 45% of the proven and probable reserves for the field.Many pre-drill uncertainties remain. The exploration and development wells are located primarily along the crest of the structure, leaving significant gross rock volume uncertainty on the flanks of the field. Qualitative use of amplitudes provides some insight into the Legendre North Field but not the Legendre South Field where the imaging is poor. The development wells were drilled horizontally and did not intersect any fluid contacts.Early field life has brought some surprises, despite a rigorous assessment of uncertainty during the field development planning process. Higher than expected gas-oil ratios suggested a saturated oil with small primary gas caps, rather than the predicted under-saturated oil. Due to the larger than expected gas volumes, the gas reinjection system proved to have inadequate redundancy resulting in constrained production from the field. The pre-drill geological model has required significant changes to reflect the drilling and production results to date. The intra-field shales needed to be areally much smaller than predicted to explain well intersections and production performance. This is consistent with outcrop analogues.Surprises are common when an oil field is first developed and often continue to arise during secondary development phases. Learnings, in the context of subsurface uncertainty, from other oil fields in the greater North West Shelf are compared briefly to highlight the importance of managing uncertainty during field development planning. It is important to have design flexibility to enable facility adjustments to be made easily, early in field life.

1994 ◽  
Vol 34 (1) ◽  
pp. 92
Author(s):  
G. B. Salter ◽  
W. P. Kerckhoff

Development of the Cossack and Wanaea oil fields is in progress with first oil scheduled for late 1995. Wanaea oil reserves are estimated in the order of 32 x 106m3 (200 MMstb) making this the largest oil field development currently underway in Australia.Development planning for these fields posed a unique set of challenges.Key subsurface uncertainties are the requirement for water injection (Wanaea only) and well numbers. Strategies for managing these uncertainties were studied and appropriate flexibility built-in to planned facilities.Alternative facility concepts including steel/concrete platforms and floating options were studied-the concept selected comprises subsea wells tied-back to production/storage/export facilities on an FPSO located over Wanaea.In view of the high proportion of costs associated with the subsea components, significant effort was focussed on flowline optimisation, simplification and cost reduction. These actions have led to potential major economic benefits.Gas utilisation options included reinjection into the oil reservoirs, export for re-injection into North Rankin or export to shore. The latter requires the installation of an LPG plant onshore and was selected as the simplest, safest and the most economically attractive method.


2021 ◽  
Author(s):  
Qasem Dashti ◽  
Saad Matar ◽  
Hanan Abdulrazzaq ◽  
Nouf Al-Shammari ◽  
Francy Franco ◽  
...  

Abstract A network modeling campaign for 15 surface gathering centers involving more than 1800 completion strings has helped to lay out different risks on the existing surface pipeline network facility and improved the screening of different business and action plans for the South East Kuwait (SEK) asset of Kuwait Oil Company. Well and network hydraulic models were created and calibrated to support engineers from field development, planning, and operations teams in evaluating the hydraulics of the production system for the identification of flow assurance problems and system optimization opportunities. Steady-state hydraulic models allowed the analysis of the integrated wells and surface network under multiple operational scenarios, providing an important input to improve the planning and decision-making process. The focus of this study was not only in obtaining an accurate representation of the physical dimension of well and surface network elements, but also in creating a tool that includes standard analytical workflows able to evaluate wells and surface network behavior, thus useful to provide insightful predictive capability and answering the business needs on maintaining oil production and controlling unwanted fluids such as water and gas. For this reason, the model needs to be flexible enough in covering different network operating conditions. With the hydraulic models, the evaluation and diagnosis of the asset for operational problems at well and network level will be faster and more effective, providing reliable solutions in the short- and long-terms. The hydraulic models enable engineers to investigate multiple scenarios to identify constraints and improve the operations performance and the planning process in SEK, with a focus on optimal operational parameters to establish effective wells drawdown, evaluation of artificial lifting requirements, optimal well segregation on gathering centers headers, identification of flow assurance problems and supporting production forecasts to ensure effective production management.


Author(s):  
O. R. Kondrat ◽  
O. A. Lukin

Oil production is a complex process that requires modern technologies, work experience and responsible personnel to implement cost-effective projects. Oil field exploitation processes stimulation or modeling is a method for researching exploitation objects on their analogs (models) in order to determine characteristics of available projected objects and make them distinct. The main objective of this research is to explore possibility and establishment of hydrodynamic stimulation results application effectiveness as a factor for decisions-making concerning oil or gas fields exploitation. The research, regarding optimization of oil field exploitation system, outlined the main directions and possibilities of oil extraction from depleted oil fields enhancement, and the hydrodynamic stimulation process as the main tool for solving such problems. The study of efficiency of oil and gas field development presupposed developing geological and technological model of a hypothetical deposit with technological indicators of a real Ukraine deposit. The hydrodynamic model was adapted for all wells according to actual data. All geological and technological measures, carried out in the sight, were also modelled. Field exploitation history was adapted. Oil field exploitation system was optimized by improving the reservoir pressure enhancement system in the real field. Different variants of field exploitation were  considered. They include the conversion of the producing well in the injection well, whereas the well in the vaulted part is injected.


2020 ◽  
pp. 31-43
Author(s):  
T. K. Apasov ◽  
G. T. Apasov ◽  
E. E. Levitina ◽  
E. I. Mamchistova ◽  
N. V. Nazarova ◽  
...  

Despite the current political and economic situation in Russia, mining in small oil fields is important and topical issue. We have conducted a geological and field analysis of the development of one of such small oil fields from setting into operation to shut down and have identified the reasons for the low production of oil reserves and the failure to achieve the design oil recovery factor. At the same time, the field has sufficient reserves of recoverable reserves, and there is an available transport infrastructure, which proves the necessity to consider rerun it for the development. For this purpose, geological and technical actions have been developed and are being proposed for implementation to improve the efficiency of field development. These actions envisage implementation in two stages: the first with minimal costs and the second with higher costs. At the first stage, at the existing reservoir pressure, we recommend to perform forced fluid withdrawals with an increase in depression on the reservoir. At the second stage, we offer actions at a higher cost, such as hydraulic fracturing, sidetracking. As a result of the analysis, actions have been developed to increase selection from initial recoverable reserves and increase the economic efficiency when the field is rerun.


2021 ◽  
Author(s):  
Sunanda Magna Bela ◽  
Abdil Adzeem B Ahmad Mahdzan ◽  
Noor Hidayah A Rashid ◽  
Zairi A Kadir ◽  
Azfar Israa Abu Bakar ◽  
...  

Abstract Gravel packing in a multilayer reservoir during an infill development project requires treating each zone individually, one after the other, based on reservoir characterization. This paper discusses the installation of an enhanced 7-in. multizone system to achieve both technical and operational efficiency, and the lessons learned that enabled placement of an optimized high-rate water pack (HRWP) in the two lower zones and an extension pack in the uppermost zone. This new approach helps make multizone cased-hole gravel-pack (CHGP) completions a more technically viable and cost-effective solution. Conventional CHGPs are limited to either stack-pack completions, which can incur high cost because of the considerable rig time required for multizone operations, or alternate-path single-trip multizone completions that treat all the target zones simultaneously, with one pumping operation. However, this method does not allow for individual treatment to suit reservoir characterization. The enhanced 7-in. multizone system can significantly reduce well completion costs and pinpoint the gravel placement technique for each zone, without pump-rate limitations caused by excessive friction in the long interval system, and without any fiuid-loss issues after installation because of the modular sliding side-door (SSD) screen design feature. A sump packer run on wireline acts as a bottom isolation packer and as a depth reference for subsequent tubing-conveyed perforating (TCP) and wellbore cleanup (WBCU) operations. All three zones were covered by 12-gauge wire-wrapped modular screens furnished with blank pipe, packer extension, and straddled by two multizone isolation packers between the zones, with a retrievable sealbore gravel-pack packer at the top. The entire assembly was run in a single trip, therefore rig time optimization was achieved. The two lower zones were treated with HRWPs, while the top zone was treated with an extension pack. During circulation testing on the lowermost zone, high pumping pressure was recorded, and after thorough observation of both pumping parameters and tool configuration, it was determined that the reduced inner diameter (ID) in the shifter might have been a causal factor, thereby restricting the flow area. This was later addressed with the implementation of a perforated pup joint placed above the MKP shifting tool. The well was completed within the planned budget and time and successfully put on sand-free production, exceeding the field development planning (FDP) target. The enhanced 7-in. multizone system enabled the project team to beat the previous worldwide track record, which was an HRWP treatment only. As a result of proper fluid selection and rigorous laboratory testing, linear gel was used to transport 3 ppa of slurry at 10 bbl/min, resulting in a world-first extension pack with a 317-lbm/ft packing factor.


2021 ◽  
Author(s):  
Rasim Serdar Rodoplu ◽  
Adegbenga O. Sobowale ◽  
Jon E. Hanson ◽  
Beau R. Wright

Abstract Multistage fracturing (MSF) ball drop completion systems have been utilized around the globe for effectively treating formations completed as open hole and cemented. Multiple, high-rate hydraulic fracturing stages are pumped through these completions while gaining efficiency during pumping operations. A challenge within the industry was developing systems that are capable of higher pressures (greater than 10k psi) while still being able to be deployed in challenging openhole environments with minimum equipment and intervention requirements. This paper will discuss the planning, deployment and fracturing execution operations of an improved version of one of these systems. To be able to effectively utilize any MSF completion system; formation properties, deployment environment, lateral length, openhole size, liner size, and tubing movements during fracturing should be thoroughly analyzed and equally considered. To create a reliable system, another important consideration is how the system will be deployed; a long string to surface, or will it be deployed as part of a liner hanger system? In the case of the latter, it should be compatible with the liner hanger system by accommodating multiple balls to set and release the hanger system and actuate the openhole packers. In tight formation environments, where treating pressure differentials reaches as high as 15,000 psi during fracturing operations, openhole packers that are capable of holding these pressures in challenging openhole conditions are needed. Not only the packers but also the remaining completion system components need to be capable of withstanding, including burst, collapse, and ball-to-ball seat differential while simultaneously accommodating the pressure with cooling and ballooning induced tubing movement caused by these high pressure treatments. Improving such a robust design with innovative solutions, such as dissolvable frac balls that can handle 15,000 psi differential, optimizes the overall process. The completion design, deployment, and subsequent fracturing operations on a well showcases how effective consideration of components operates as a system can create a reliable MSF system. It also demonstrates how close collaboration between reservoir management, production engineering, completion experts, and vendor results in a coordination of efforts that eliminates operational hazards, thus ensuring smooth operations. The successful deployment of an openhole MSF completion system that can handle 15,000 psi with dissolving frac balls and eliminating openhole anchors helped pave the way to deal with tighter formations in an efficient and cost-effective manner. With the help of this new technology, the well planners were able to address operational challenges that would have otherwise required additional equipment or would have limited deployment capabilities. The engineering approach and design to develop this completion system and utilization in the right candidate confirmed the benefit of the novel completion for field development options.


1999 ◽  
Author(s):  
G. Fabel ◽  
T. Neunhöffer ◽  
D. Rudschinski ◽  
J. Sasse ◽  
T. Scheer

Sign in / Sign up

Export Citation Format

Share Document