Biodegradation behaviour of hydroxyapatite-containing self-sealing micro-arc-oxidation coating on pure Mg

A modern trend in traumatology, orthopedics, and implantology is the development of materials and coatings with an amorphous–crystalline structure that exhibits excellent biocopatibility. The structure and physico–chemical and biological properties of calcium phosphate (CaP) coatings deposited on Ti plates using the micro-arc oxidation (MAO) method under different voltages (200, 250, and 300 V) were studied. Amorphous, nanocrystalline, and microcrystalline statesof CaHPO4 and β-Ca2P2O7were observed in the coatings using TEM and XRD. The increase in MAO voltage resulted in augmentation of the surface roughness Ra from 2.5 to 6.5 µm, mass from 10 to 25 mg, thickness from 50 to 105 µm, and Ca/P ratio from 0.3 to 0.6. The electrical potential (EP) of the CaP coatings changed from −456 to −535 mV, while the zeta potential (ZP) decreased from −53 to −40 mV following an increase in the values of the MAO voltage. Numerous correlations of physical and chemical indices of CaP coatings were estimated. A decrease in the ZP magnitudes of CaP coatings deposited at 200–250 V was strongly associated with elevated hTERT expression in tumor-derived Jurkat T cells preliminarily activated with anti-CD2/CD3/CD28 antibodies and then contacted in vitro with CaP-coated samples for 14 days. In turn, in vitro survival of CD4+ subsets was enhanced, with proinflammatory cytokine secretion of activated Jurkat T cells. Thus, the applied MAO voltage allowed the regulation of the physicochemical properties of amorphous–crystalline CaP-coatings on Ti substrates to a certain extent. This method may be used as a technological mechanism to trigger the behavior of cells through contact with micro-arc CaP coatings. The possible role of negative ZP and Ca2+ as effectors of the biological effects of amorphous–crystalline CaP coatings is discussed. Micro-arc CaP coatings should be carefully tested to determine their suitability for use in patients with chronic lymphoid malignancies.

Download Full-text

A Preliminary Study of Anodization and Electroless Ni–P Plating on AZ80 Magnesium Alloy

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.299-300.663 ◽

2011 ◽

Vol 299-300 ◽

pp. 663-666 ◽

Cited By ~ 1

Author(s):

Ping Shi ◽

Xue Dong Han

Keyword(s):

Corrosion Resistance ◽

Magnesium Alloy ◽

Weight Ratio ◽

High Strength ◽

Surface Modifications ◽

Atomic Ratio ◽

Az80 Magnesium Alloy ◽

Micro Arc Oxidation ◽

Preliminary Study ◽

Electroless Ni

Magnesium alloys are being used as structural components in industry because of their high strength to weight ratio. But their high electrochemical activity and poor corrosion resistance limited their applications. Therefore, surface modifications are needed for protection purpose. This paper studied the anodic micro-arc oxidation and electroless Ni-P plating surface modifications on AZ80 magnesium alloy. The SEM, XRD and EDS were used to characterize the surface coating. It shows that a micro-porous MgO layer with the pores size 5 – 20 μm was fabricated on the bare magnesium alloy. The nodule Ni-P deposition could be prepared on the out layer of MgO with Ni/P atomic ratio being 1.4. The pores in MgO layer could be sealed by the following Ni-P deposition. Therefore the corrosion resistance of the magnesium alloy could be further improved.

Download Full-text