Attainment of an exceptionally high strength in low-carbon steel along with modest ductility through a novel heat treatment route

2018 ◽  
Vol 98 (6) ◽  
pp. 240-251 ◽  
Author(s):  
Amir Raza Subhani ◽  
Dipak Kumar Mondal ◽  
Chandan Mondal ◽  
Joydeep Maity
Keyword(s):  
Heat Treatment ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
High Strength ◽  
Low Carbon

Heat Treatment Conditions of Low Carbon Steel Part Used in the Deep Sea

2010 ◽  
Author(s):  
Sang-Seop Lim ◽  
Chung-Gil Kang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Carbon Steel ◽  
Deep Sea ◽  
Low Carbon Steel ◽  
High Strength ◽  
Steel Part ◽  
Heat Treatment Condition ◽  
Low Carbon ◽  
Oil Consumption

With increasing oil consumption, we have to find more oil resources in the deep sea. The extreme working condition of the deep sea requires high toughness and high strength values at low temperatures. Academic institutions limited the chemical composition of the requested casting steel to meet their requirements of fracture toughness and weldability. Thus, the carbon content was set approximately 0.10% based on classification societies which required specific mechanical properties of strength, elongation, reduction area and impact energy (−40°C). In this study, we find the optimal heat treatment condition of low carbon steel (0.10%C) to obtain the desired mechanical properties at low temperature (−40°C) according to different quenching parameters (heating times) and tempering parameters (heating temperatures, cooling methods).

Heat Treatment Regime Optimization for High-Strength Low-Carbon Steel Forged Slabs

Metallurgist ◽  
2018 ◽  
Vol 61 (9-10) ◽  
pp. 777-781
Author(s):  
V. V. Tsukanov ◽  
V. G Milyuts ◽  
O. E. Nigmatulin ◽  
S. A. Golosienko ◽  
S. V. Efimov ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
High Strength ◽  
Treatment Regime ◽  
Low Carbon ◽  
Heat Treatment Regime

Experimental study of the mechanical and corrosion properties of ethyl silicate resin applied on low carbon steel

2021 ◽  
Vol 2 (108) ◽  
pp. 68-74
Author(s):  
M. Ali ◽  
J.H. Mohmmed ◽  
A.A. Zainulabdeen
Keyword(s):  
Heat Treatment ◽  
Carbon Steel ◽  
Open Circuit Potential ◽  
Low Carbon Steel ◽  
Open Circuit ◽  
Treatment Temperature ◽  
Ethyl Silicate ◽  
Low Carbon ◽  
Corrosion Properties ◽  
Mixture Ratio

Purpose: This work aimed at evaluating the properties of the ethyl silicate-based coating that can be applied on low carbon steel. Design/methodology/approach: Two mixture ratio types (2:1, and 3:2) of resin and hardener respectively were used to prepared two specimen models (A and B). Findings: It found that some mechanical properties (tensile, hardness, and impact strength) of ethyl silicate resin were evaluated according to standard criteria. Research limitations/implications: The effect of heat treatments at various temperatures (100, 150, and 200°C) and holding at different times (10, 20 & 30) min on hardness was investigated. Practical implications: Moreover, an open circuit potential corrosion test with a solution of 3.5% Sodium Chloride at room temperature and 60°C was used to determine the corrosion resistance of low carbon steel specimens coated with the two mixture types. Originality/value: The effects of mixture ratios (for resin and hardener) and heat treatment conditions on properties of ethyl silicate-based coating were studied. From obtained results, acceptable values of tensile, hardness, and toughness were recorded. Increasing heat treatment temperature and holding time leads to enhance hardness for both model types. An open circuit potential (OCP) tests show that there is an enhancement of protective properties of ethyl silicate coatings with mixture type B in comparison with type A was achieved. Generally, the results indicate that specimen model B has higher properties as compared with specimen model A.

An Exceptional Synergy of High Strength, Ductility and Toughness in a Gradient-Structured Low-Carbon Steel

2018 ◽  
Vol 27 (11) ◽  
pp. 5788-5793
Author(s):  
Yindong Shi ◽  
Lina Wang ◽  
Yulong Zhang ◽  
Hailong Xie ◽  
Yajun Zhao
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
High Strength ◽  
Low Carbon

Interfacial segregation at Cu-rich precipitates in a high-strength low-carbon steel studied on a sub-nanometer scale

2006 ◽  
Vol 54 (3) ◽  
pp. 841-849 ◽  
Author(s):  
Dieter Isheim ◽  
Michael S. Gagliano ◽  
Morris E. Fine ◽  
David N. Seidman
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
High Strength ◽  
Nanometer Scale ◽  
Low Carbon ◽  
Interfacial Segregation

scholarly journals Quantitative Description of External Force Induced Phase Transformation in Silicon–Manganese (Si–Mn) Transformation Induced Plasticity (TRIP) Steels

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3781
Author(s):  
Zhongping He ◽  
Huachu Liu ◽  
Zhenyu Zhu ◽  
Weisen Zheng ◽  
Yanlin He ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Carbon Steel ◽  
Trip Steel ◽  
Retained Austenite ◽  
Low Carbon Steel ◽  
High Strength ◽  
High Plasticity ◽  
Low Carbon ◽  
Transformation Induced Plasticity ◽  
Trip Steels

Transformation Induced Plasticity (TRIP) steels with silicon–manganese (Si–Mn) as the main element have attracted a lot of attention and great interest from steel companies due to their low price, high strength, and high plasticity. Retained austenite is of primary importance as the source of high strength and high plasticity in Si–Mn TRIP steels. In this work, the cold rolled sheets of Si–Mn low carbon steel were treated with TRIP and Dual Phase (DP) treatment respectively. Then, the microstructure and composition of the Si–Mn low carbon steel were observed and tested. The static tensile test of TRIP steel and DP steel was carried out by a CMT5305 electronic universal testing machine. The self-built true stress–strain curve model of TRIP steel was verified. The simulation results were in good agreement with the experimental results. In addition, the phase transformation energy of retained austenite and the work borne by austenite in the sample during static stretching were calculated. The work done by austenite was 14.5 J, which was negligible compared with the total work of 217.8 J. The phase transformation energy absorption of retained austenite in the sample was 9.12 J. The role of retained austenite in TRIP steel is the absorption of excess energy at the key place where the fracture will occur, thereby increasing the elongation, so that the ferrite and bainite in the TRIP steel can absorb energy for a longer time and withstand more energy.

Sign in / Sign up

Export Citation Format

Share Document