Effect of Heat Treatment on Wear Resistance and Impact Strength of High Chromium White Cast Iron

Cast Metals ◽  
1989 ◽  
Vol 2 (1) ◽  
pp. 20-22
Author(s):  
A. Basak ◽  
J. Penning ◽  
J. Dilewijns
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Cast Iron ◽  
Impact Strength ◽  
White Cast Iron ◽  
High Chromium

scholarly journals Heat Treatment in High Chromium White Cast Iron Ti Alloy

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Khaled M. Ibrahim ◽  
Mervat M. Ibrahim
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Wear Resistance ◽  
Cast Iron ◽  
Impact Toughness ◽  
White Cast Iron ◽  
High Chromium ◽  
Eutectic Carbides ◽  
Secondary Carbides ◽  
Ti Addition

The influence of heat treatment on microstructure and mechanical properties of high chromium white cast iron alloyed with titanium was investigated. The austenitizing temperatures of 980°C and 1150°C for 1 hour each followed by tempering at 260°C for 2 hours have been performed and the effect of these treatments on wear resistance/impact toughness combination is reported. The microstructure of irons austenitized at 1150°C showed a fine precipitate of secondary carbides (M6C23) in a matrix of eutectic austenite and eutectic carbides (M7C3). At 980°C, the structure consisted of spheroidal martensite matrix, small amounts of fine secondary carbides, and eutectic carbides. Titanium carbides (TiC) particles with cuboidal morphology were uniformly distributed in both matrices. Irons austenitized at 980°C showed relatively higher tensile strength compared to those austenitized at 1150°C, while the latter showed higher impact toughness. For both cases, optimum tensile strength was reported for the irons alloyed with 1.31% Ti, whereas maximum impact toughness was obtained for the irons without Ti-addition. Higher wear resistance was obtained for the samples austenitized at 980°C compared to the irons treated at 1150°C. For both treatments, optimum wear resistance was obtained with 1.3% Ti.

Study of the durability of the working body the dryer

2020 ◽  
pp. 56-60
Author(s):  
A. P. Chernysh
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Cast Iron ◽  
White Cast Iron ◽  
Low Cost ◽  
Functional Surface ◽  
Wear Coatings

In this article, the plant for heat treatment of grain material, namely perfo-rated spiral operating part, developed by the authors was chosen as the object of improving the wear resistance. The research was conducted in the laboratory of the Technology of Metals and Machinery Repair Department of Kemerovo State Agricultural Institute. The aim of the research is to select the most appropriate method of hardening the functional surface of perforated spiral operating part with the use of low-cost anti-wear coatings. The basis for choosing the method of surfacing the coating was the use of a method of forming the technological repair units (TRU), which allowed electric spark treatment with unalloyed white cast iron.

Microstructure and wear resistance of spray formed high chromium white cast iron

2004 ◽  
Vol 375-377 ◽  
pp. 589-594 ◽  
Author(s):  
A.H. Kasama ◽  
A.J. Mourisco ◽  
C.S. Kiminami ◽  
W.J. Botta Fo ◽  
C. Bolfarini
Keyword(s):  
Wear Resistance ◽  
Cast Iron ◽  
White Cast Iron ◽  
High Chromium

Interfacial Characteristics and Wear Resistance of WCp/White-Cast-Iron Composites

2007 ◽  
Vol 26-28 ◽  
pp. 293-296 ◽  
Author(s):  
Guo Shang Zhang ◽  
Yi Min Gao ◽  
Jian Dong Xing ◽  
Shi Zhong Wei ◽  
Xi Liang Zhang
Keyword(s):  
Wear Resistance ◽  
Cast Iron ◽  
White Cast Iron ◽  
Centrifugal Casting ◽  
Casting Process ◽  
Iron Matrix ◽  
High Chromium ◽  
X Ray ◽  
High Chromium Cast Iron ◽  
Wear Tests

To improve the wear resistance of high chromium white cast iron under severe abrasive conditions, a composites layer was designed for wear surface, which were locally reinforced with WC particles. And the local composites were successfully fabricated by optimized centrifugal casting process. Then the interface between WC and iron matrix was analyzed with scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). And three body wear tests were carried out on a self-made rig to investigate the wear resistance of the composites. For comparison, the wear tests of high chromium white cast iron were also carried out under the same conditions. The results show that: There are no defects such as inclusion, crack, gas pore and so on in the obtained composites layer, which with a uniform thickness of 10 mm. WC particles are homogeneously distributed in the composites layer and tightly bonded with the iron matrix. The WC particles are partially dissolved in the iron matrix during centrifugal casting. The elements W, C and Fe react to form new carbides such as Fe3W3C or M23C6, which precipitate around former WC particles during subsequent solidification. So the interface between WC particles and the iron matrix is a strong metallurgical bonding. WC particles in the composites layer can effectively resist cutting by the abrasive, and then protect the matrix. The wear resistance of the composites layer is 7.23 times of that of high chromium cast iron.

scholarly journals The Effect of Palm Kernel Shell Ash on the Mechanical and Wear Properties of White Cast Iron

2020 ◽  
Vol 45 (2) ◽  
pp. 20-27
Author(s):  
Kayode I. Fesomade ◽  
Damilola D. Alewi ◽  
Saliu O. Seidu ◽  
Sheriff O. Saka ◽  
Bonaventure I. Osuide ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Cast Iron ◽  
Elemental Composition ◽  
White Cast Iron ◽  
Palm Kernel ◽  
Rotary Furnace ◽  
Wear Properties ◽  
Palm Kernel Shell ◽  
The Matrix

This study investigates the influence of palm kernel shell ash (PKSA) on mechanical and wear properties of white cast iron (WCI) particularly its influence on its microstructure, elemental composition, hardness and wear resistance. The PKSA was characterized to determine its elemental composition, and it was found to contain high amount of silicon (Si) and iron (Fe) followed by calcium (Ca) and other trace elements. The cast iron was cast into rods of specific dimension with sand casting method using rotary furnace to re-melt cast iron scrap. The WCI rods were then cut into bits for the various test. Heat treatment operation was carried out to determine its properties. Upon completion of the examinations, it was found that the PKSA increased the cementite phase within the matrix of the cast iron, and reduced the pearlitic phase and graphite formation, which gave it increased hardness, and perfect wear resistance due to the increment in carbon content and reduction in silicon content. Also, upon heat treatment, it was found that the PKSA reduced the pearlitic phase within the matrix of the cast iron, increases the formation of transformed ledeburites, austenitic dendrites and tempered graphite, which lead to increased machinability and ductility as well as to reduced hardness, and wear resistance when compared to non-heat treated samples.

scholarly journals Microstructural evolution during austempering of a ASTM A-532 CLASS III type high chromium white cast iron undergoing abrasive wear

2017 ◽  
Vol 26 (46) ◽  
Author(s):  
Oscar Fabián Higuera-Cobos ◽  
Jeison Bucurú-Vasco ◽  
Andrés Felipe Loaiza-Patiño ◽  
Mónica Johanna Monsalve-Arias ◽  
Dairo Hernán Mesa-Grajales
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Cast Iron ◽  
Chemical Composition ◽  
Abrasive Wear ◽  
Retained Austenite ◽  
White Cast Iron ◽  
Abrasive Wear Resistance ◽  
Class Iii ◽  
High Chromium

This paper studies the influence of variables such as holding temperatures and times during austempering of High Chromium White Cast Iron (HCWCI), with the following chemical composition: Cr 25 %, C 3 %, Si 0.47 %, Mn 0.74 % and Mo 1.02 %. The aim of the austempering was to modify the percentage of retained austenite and its correlation to abrasive wear resistance under different conditions.Microhardness tests, SEM-EDS and XRD were performed to determine mechanical properties, chemical composition, and type of carbides and microstructures present, respectively. The tests complied with the ASTM G-65 standard. Results showed that the best performance against abrasion was achieved for austempering at 450 ºC with holding time of 6 hours.

Effect of carbides on the wear resistance of white cast iron alloyed with 12.7 wt.-% Cr and nickel

2020 ◽  
Vol 62 (8) ◽  
pp. 788-792
Author(s):  
Tanju Teker ◽  
S. Osman Yilmaz ◽  
Tekirdağ Teker
Keyword(s):  
Heat Treatment ◽  
Wear Resistance ◽  
Cast Iron ◽  
White Cast Iron ◽  
Volume Fraction ◽  
High Wear Resistance ◽  
Homogeneous Distribution ◽  
Nickel Concentration ◽  
Carbide Size ◽  
Wear Tests

Abstract White cast iron with about 12.7 wt.-% chromium was alloyed with Ni, W and Mo for heat treatment applications. Heat treatments were performed at a range of 850-1050 °C for 1 h in order to distribute M7C3 carbides homogeneously in an environment of high wear resistance. The contents of the C, Cr, Ni, Mo, Mn and Si elements selected for the alloys were similar, though a 6 wt.-% nickel concentration was chosen. Microstructural changes in the specimens were examined by scanning electron microscopy (SEM) and optical microscopy (OM). Macro-hardness, average carbide size and volume fraction were analyzed. Wear tests were carried out under different loads of 10, 20 and 30 N. It was seen that heat treatment changed the carbide size and homogeneous distribution of the carbides. Moreover, the addition of nickel to HCrWCI increased fracture toughness and reduced the wear rate.

Sign in / Sign up

Export Citation Format

Share Document