Low-temperature performance grade characterisation of asphalt binder using the dynamic shear rheometer

2020 ◽  
pp. 1-13 ◽  
Author(s):  
Zhe ‘Alan’ Zeng ◽  
B. Shane Underwood ◽  
Cassie Castorena
Keyword(s):  
Low Temperature ◽  
Asphalt Binder ◽  
Dynamic Shear ◽  
Dynamic Shear Rheometer ◽  
Performance Grade ◽  
Temperature Performance ◽  
Low Temperature Performance

Field Validation of New Superpave Low-Temperature Binder Specification Procedure: Performance Data from Pennsylvania Test Sections

2000 ◽  
Vol 1728 (1) ◽  
pp. 60-67 ◽  
Author(s):  
Raj Dongré ◽  
Mark G. Bouldin ◽  
Dean A. Maurer
Keyword(s):  
Low Temperature ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Direct Tension ◽  
Transverse Cracking ◽  
Performance Grade ◽  
Temperature Performance ◽  
Test Road ◽  
Low Temperature Performance ◽  
And Performance

A new specification procedure was proposed recently to determine the low-temperature performance grade of asphalt binders. This new procedure uses bending beam rheometer (BBR) and direct tension test (DTT) data at two temperatures to determine the low-temperature grade of an asphalt binder. A study was conducted to validate this procedure by using asphalt binder retained samples from the widely published test road in Pennsylvania. This road was constructed in 1976 in Elk County, and performance—including low-temperature transverse cracking index—was monitored over 6 years. In this study, the retained binder samples from test sections T-1 to T-6 were tested with the BBR and the new Superpave® DTT. The data from these two tests were analyzed to obtain critical cracking temperatures and low-temperature performance grades. Results indicate that the new procedure correctly predicts the temperature at which cracking was observed in the field.

Effect of Aging on the Low Temperature Performance of Asphalt Binder

2013 ◽  
Vol 438-439 ◽  
pp. 369-372
Author(s):  
Ning Li Li ◽  
Xin Po Zhao ◽  
Cai Li Zhang ◽  
Hu Hui Li ◽  
Qing Yi Xiao
Keyword(s):  
Thin Film ◽  
Low Temperature ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Bending Beam Rheometer ◽  
Oven Test ◽  
Modified Asphalt ◽  
Temperature Performance ◽  
Different Types ◽  
Low Temperature Performance

During the service of asphalt pavement, the aging makes asphalt binder become brittle, gradually lose flexibility and adhesion. All these result in the low-temperature properties of asphalt pavement to be poor. This paper conducts the rolling thin film oven test (RTFOT) and pressure aging vessel (PAV) test on base asphalt and rubber-modified asphalt respectively. The bending beam rheometer (BBR) test was conducted on original asphalts, rolling thin film oven test (RTFOT) residuals and RTFOT + pressure aging vessel (PAV) residuals of base asphalt and rubber-modified asphalt respectively. Results indicate that the low-temperature properties of all aged asphalts were declined. The attenuation of low-temperature properties of RTFOT + PAV residuals is larger than that of the RTFOT residuals. The attenuation of different types of asphalt is different. From the overall trend, effect of aging on the low-temperature properties of asphalt binder reduced as the test temperature reduction. The rubber-modified asphalt has superior low-temperature performance than that of base asphalt, and its low-temperature performance decreases more slowly than the base asphalt.

Considerations for using the 4 mm Plate Geometry in the Dynamic Shear Rheometer for Low Temperature Evaluation of Asphalt Binders

2019 ◽  
Vol 2673 (11) ◽  
pp. 649-659 ◽  
Author(s):  
Ramez Hajj ◽  
Angelo Filonzi ◽  
Syeda Rahman ◽  
Amit Bhasin
Keyword(s):  
Low Temperature ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Asphalt Pavements ◽  
Dynamic Shear ◽  
Dynamic Shear Rheometer ◽  
Reclaimed Asphalt ◽  
Load Response ◽  
Linear Viscoelastic ◽  
Analytical Approaches

The low-temperature properties of asphalt binder have attracted attention in recent years thanks to an increase in the use of reclaimed asphalt pavements (RAP). Traditional methods to evaluate the low-temperature properties of the binder require a large amount of binder that needs to be recovered from RAP samples for testing with a Bending Beam Rheometer (BBR). To economize on sample size for RAP materials and also for emulsion residues, previous researchers have explored the potential of using a 4 mm diameter specimen with a Dynamic Shear Rheometer (DSR) in lieu of the BBR. To compare results from frequency sweep tests conducted using the DSR with results from the BBR, data from the former need to be converted to time domain and subsequently from a shear load response to an axial load response. Previous research studies have developed methods to accomplish these two conversions to compare data from the DSR with data from the BBR. The objective of this study is to examine some of these methods from the literature and elsewhere based on the principles of linear viscoelastic interconversion using a set of 11 different binders. Results using different analytical approaches from this study show that the DSR has good repeatability and verify that it can be used as a surrogate for the BBR to determine low-temperature properties, while exercising some caution with some of the assumptions related to Poisson’s ratio.

Low-Temperature Performance of Toner-Modified Asphalt Binder

2019 ◽  
Vol 145 (3) ◽  
pp. 04019022 ◽  
Author(s):  
Mohammad Ali Notani ◽  
Fereidoon Moghadas Nejad ◽  
Ellie H. Fini ◽  
Pouria Hajikarimi
Keyword(s):  
Low Temperature ◽  
Asphalt Binder ◽  
Modified Asphalt ◽  
Temperature Performance ◽  
Modified Asphalt Binder ◽  
Low Temperature Performance

Experimental Study on Polyphosphoric Acid (PPA) Modified Asphalt Binders

2010 ◽  
Vol 152-153 ◽  
pp. 288-294 ◽  
Author(s):  
Wei Dong Cao ◽  
Shu Tang Liu ◽  
Hong Lu Mao
Keyword(s):  
Low Temperature ◽  
Softening Point ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Modified Asphalt ◽  
Temperature Performance ◽  
Point Test ◽  
Low Temperature Performance ◽  
Four Levels ◽  
Temperature Susceptibility

Polyphosphric acid (PPA) modified asphalt binders were produced in the laboratory using one base asphalt and four levels of PPA contents (0.6%, 1.0%, 1.5% and 2.0% by weight of base asphalt). Penetration test, softening point test, rotation viscosity test, creep test with bending beam rheometer (BBR) and four components test were carried out to study the performance of PPA modified asphalt binders and possible modification mechanism. The results indicate that the high-temperature performance of PPA modified asphalt binders are obviously improved and temperature susceptibility are decreased, but the low-temperature performance slightly decline compared with base asphalt. The PPA content has a very significant effect on softening point whereas it has no significant influence on low-temperature performance according to variance analysis (ANOVA). Finally, four components test reveals that the primary modification mechanism of PPA is the change of chemical composition of asphalt binder.

scholarly journals Evaluation of Low- and Intermediate-Temperature Performance of Bio Oil-Modified Asphalt Binders

2021 ◽  
Vol 13 (7) ◽  
pp. 4039
Author(s):  
Sara A. Alattieh ◽  
Ghazi G. Al-Khateeb ◽  
Waleed Zeiada
Keyword(s):  
Low Temperature ◽  
Asphalt Binder ◽  
Fatigue Cracking ◽  
Asphalt Binders ◽  
Tensile Stresses ◽  
Modified Asphalt ◽  
Temperature Performance ◽  
Bio Oil ◽  
Low Temperature Cracking ◽  
Low Temperature Performance

Fatigue cracking and low-temperature cracking are two major distresses that occur in asphalt pavements. Fatigue cracking is a load-associated distress caused by the tensile stresses at the bottom/top of the asphalt concrete (AC) layer due to repeated traffic loading. On the other hand, low-temperature cracking occurs when tensile stresses built up with in the AC layer at low temperatures exceed the tensile strength of that layer. In this study, the performance of date seeds oil bio-modified asphalt binders (DSO-BMB) is evaluated against fatigue and low-temperature cracking. The DSO-BMBs are prepared using volume ratios of 1.5, 2.5, 3.5, 4.5, and 5.5% date seeds oil-to-asphalt binder. The base asphalt binder used in the study is a 60/70-penetration grade with a Superpave performance grade (PG) of PG 64–16. The dynamic shear rheometer (DSR) standard test was used to assess the fatigue performance of the bio-modified binders (BMBs), while the bending beam rheometer (BBR) test was used to test the BMBs for low-temperature performance. In addition, the DSR linear amplitude sweep (LAS) test was used to evaluate the fatigue tolerance behavior of the DSO-BMBs. The analysis and results of the study showed that the bio-oil enhanced the low-temperature performance. The low PG grade improved from −16 °C for the control asphalt binder to −28 °C for the BMB. Additionally, the fatigue resistance of the BMBs was improved as illustrated by the damage–characteristic curves of the modified asphalt binders from the visco-elastic continuum damage (VECD) analysis and the increase in the number of cycles to fatigue failure (Nf).

Sign in / Sign up

Export Citation Format

Share Document