Experimental Study on Heat Transfer Augmentation for High Heat Flux Removal in Rib-Roughened Narrow Channels

1998 ◽  
Vol 35 (9) ◽  
pp. 671-678 ◽  
Author(s):  
Md. Shafiqul ISLAM ◽  
Ryutaro HINO ◽  
Katsuhiro HAGA ◽  
Masanori MONDE ◽  
Yukio SUDO
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Flux ◽  
High Heat ◽  
High Heat Flux ◽  
Narrow Channels ◽  
Heat Transfer Augmentation ◽  
Rib Roughened

Preliminary Experimental Study on Hypervapotron Heat Transfer for High Heat Flux Components

2018 ◽  
Vol 46 (5) ◽  
pp. 1372-1376
Author(s):  
Delin Chu ◽  
Haiyan Jiang ◽  
Haifei Deng ◽  
Jinhong Yang ◽  
Weihua Wang
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Flux ◽  
High Heat ◽  
High Heat Flux

Experimental Study of Single Phase Heat Transfer and Pressure Loss in a Spiraling Radial Inflow Microchannel Heat Sink

2015 ◽  
Vol 137 (7) ◽  
Author(s):  
Maritza Ruiz ◽  
Van P. Carey
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Flux ◽  
Single Phase ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Enhanced Heat Transfer ◽  
Heat Transfer Coefficients ◽  
Gap Height

This paper presents an experimental study of the heat transfer and pressure drop characteristics of a single phase high heat flux microchannel cooling system with spiraling radial inflow. The heat sink provides enhanced heat transfer with a simple inlet and outlet design while providing uniform flow distribution. The system is heated from one conducting wall made of copper and uses water as a working fluid. The microchannel has a 1 cm radius and a 300 μm gap height. Experimental results show, on average, a 76% larger pressure drop compared to an analytic model for laminar flow in a parallel disk system with spiral radial inflow. The mean heat transfer coefficients measured are up to four times the heat transfer coefficient for unidirectional laminar fully developed flow between parallel plates with the same gap height. Flow visualization studies indicate the presence of secondary flows and the onset of turbulence at higher flow rates. Combined with the thermally developing nature of the flow, these characteristics lead to enhanced heat transfer coefficients relative to the laminar parallel plate values. Another beneficial feature of this device, for high heat flux cooling applications, is that the thermal gradients on the surface are small. The average variation in surface temperature is 18% of the total bulk fluid temperature gain across the device. The system showed promising cooling characteristics for electronics and concentrated photovoltaics applications with a heat flux of 113 W/cm2 at a surface temperature of 77 °C and a ratio of pumping power to heat rate of 0.03%.

Development of Cooling System for a Large Area at High Heat Flux by Using Flow Boiling in Narrow Channels

2009 ◽  
Author(s):  
Shinichi Miura ◽  
Yukihiro Inada ◽  
Yasuhisa Shinmoto ◽  
Haruhiko Ohta
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Rate ◽  
Mass Velocity ◽  
Cooling System ◽  
Volumetric Flow Rate ◽  
High Heat ◽  
High Heat Flux ◽  
Gap Size ◽  
Heated Channel

Advance of an electronic technology has caused the increase of heat generation density for semiconductors densely integrated. Thermal management becomes more important, and a cooling system for high heat flux is required. It is extremely effective to such a demand using flow boiling heat transfer because of its high heat removal ability. To develop the cooling system for a large area at high heat flux, the cold plate structure of narrow channels with auxiliary unheated channel for additional liquid supply was devised and confirmed its validity by experiments. A large surface of 150mm in heated length and 30mm in width with grooves of an apex angle of 90 deg, 0.5mm depth and 1mm in pitch was employed. A structure of narrow rectangular heated channel between parallel plates with an unheated auxiliary channel was employed and the heat transfer characteristics were examined by using water for different combinations of gap sizes and volumetric flow rates. Five different liquid distribution modes were tested and their data were compared. The values of CHF larger than 1.9×106W/m2 for gap size of 2mm under mass velocity based on total volumetric flow rate and on the cross section area of main heated channel 720kg/m2s or 1.7×106W/m2 for gap size of 5mm under 290kg/m2s were obtained under total volumetric flow rate 4.5×10−5m3/s regardless of the liquid distribution modes. Under several conditions, the extensions of dry-patches were observed at the upstream location of the main heated channel resulting burnout not at the downstream but at the upstream. High values of CHF larger than 2×106W/m2 were obtained only for gap size of 2mm. The result indicates that higher mass velocity in the main heated channel is more effective for the increase in CHF. It was clarified that there is optimum flow rate distribution to obtain the highest values of CHF. For gap size of 2mm, high heat transfer coefficient as much as 7.4×104W/m2K were obtained at heat flux 1.5×106W/m2 under mass velocity 720kg/m2s based on total volumetric flow rate and on the cross section area of main heated channel. Also to obtain high heat transfer coefficient, it is more useful to supply the cooling liquid from the auxiliary unheated channel for additional liquid supply in the transverse direction perpendicular to the flow in the main heated channel.

Development of Advanced High Heat Flux Cooling System for Power Electronics

2009 ◽  
Author(s):  
Yasuhisa Shinmoto ◽  
Shinichi Miura ◽  
Koichi Suzuki ◽  
Yoshiyuki Abe ◽  
Haruhiko Ohta
Keyword(s):  
Heat Flux ◽  
Power Electronics ◽  
Critical Heat Flux ◽  
Heating Surface ◽  
Narrow Channel ◽  
High Heat ◽  
High Heat Flux ◽  
Gap Size ◽  
Narrow Channels ◽  
Very High

Recent development in electronic devices with increased heat dissipation requires severe cooling conditions and an efficient method for heat removal is needed for the cooling under high heat flux conditions. Most researches are concentrated on small semiconductors with high heat flux density, while almost no existing researches concerning the cooling of a large semiconductor, i.e. power electronics, with high heat generation density from a large cooling area. A narrow channel between parallel plates is one of ideal structures for the application of boiling phenomena which uses the cooling for such large semiconductors. To develop high-performance cooling systems for power electronics, experiments on increase in critical heat flux (CHF) for flow boiling in narrow channels by improved liquid supply was conducted. To realize the cooling of large areas at extremely high heat flux under the conditions for a minimum gap size and a minimum flow rate of liquid supplied, the structure with auxiliary liquid supply was devised to prevent the extension of dry-patches underneath flattened bubbles generated in a narrow channel. The heating surface was experimented in two channels with different dimensions. The heating surfaces have the width of 30mm and the lengths of 50mm and 150mm in the flow direction. A large width of actual power electronics is realizable by the parallel installation of the same channel structure in the transverse direction. The cooling liquid is additionally supplied via sintered metal plates from the auxiliary unheated channels located at sides or behind the main heated channel. To supply the liquid to the entire heating surface, fine grooves are machined on the heating surface for enhance the spontaneous liquid supply by the aid of capillary force. The gap size of narrow channels are varied as 0.7mm, 2mm and 5mm. Distribution of liquid flow rate to the main heated channel and the auxiliary unheated channels were varied to investigate its effect on the critical heat flux. Test liquids employed are R113, FC72 and water. The systematic experiments by using water as a test liquid were conducted. Critical heat flux values larger than 2×106W/m2 were obtained at both gap sizes of 2mm and 5mm for a heated length of 150mm. A very high heat transfer coefficient as much as 1×105W/m2K was obtained at very high heat flux near CHF for the gap size of 2mm. This paper is a summary of experimental results obtained in the past by the present authors.

Study on onset of nucleate boiling with screw tube for fusion reactor application

2021 ◽  
Author(s):  
Ji Hwan Lim ◽  
Minkyu Park
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Transfer Mechanism ◽  
High Heat Flux ◽  
Heat Transfer Mechanism ◽  
System Parameters ◽  
Smooth Tubes

Abstract The onset of nucleate boiling (ONB) is the point at which the heat transfer mechanism in fluids changes and is one of the thermo-hydraulic factors that must be considered when establishing a cooling system operation strategy. Because the high heat flux of several MW/m2, which is loaded within a tokamak, is applied under a one-side heating condition, it is necessary to determine a correlative relation that can predict ONB under special heating conditions. In this study, the ONB of a one-side-heated screw tube was experimentally analyzed via a subcooled flow boiling experiment. The helical nut structure of the screw tube flow path wall allows for improved heat transfer performance relative to smooth tubes, providing a screw tube with a 53.98% higher ONB than a smooth tube. The effects of the system parameters on the ONB heat flux were analyzed based on the changes in the heat transfer mechanism, with the results indicating that the flow rate and degree of subcooling are proportional to the ONB heat flux because increasing these factors improves the forced convection heat transfer and increases the condensation rate, respectively. However, it was observed that the liquid surface tension and latent heat decrease as the pressure increases, leading to a decrease in the ONB heat flux. An evaluation of the predictive performance of existing ONB correlations revealed that most have high error rates because they were developed based on ONB experiments on micro-channels or smooth tubes and not under one-side high heat load conditions. To address this, we used dimensional analysis based on Python code to develop new ONB correlations that reflect the influence of system parameters.

Sign in / Sign up

Export Citation Format

Share Document