Variations in Young's modulus and intrinsic stress of LPCVD-polysilicon due to high-temperature annealing

1995 ◽  
Vol 5 (2) ◽  
pp. 121-124 ◽  
Author(s):  
D Maier-Schneider ◽  
J Maibach ◽  
E Obermeier ◽  
D Schneider
Keyword(s):  
High Temperature ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Intrinsic Stress ◽  
High Temperature Annealing

scholarly journals High-Temperature Elastic Properties of Yttrium-Doped Barium Zirconate

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 968
Author(s):  
Fumitada Iguchi ◽  
Keisuke Hinata
Keyword(s):  
High Temperature ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Measurement Method ◽  
Young's Modulus ◽  
Barium Zirconate ◽  
Shear Moduli ◽  
Ceramic Fuel ◽  
Yttrium Concentration ◽  
Ceramic Fuel Cells

The elastic properties of 0, 10, 15, and 20 mol% yttrium-doped barium zirconate (BZY0, BZY10, BZY15, and BZY20) at the operating temperatures of protonic ceramic fuel cells were evaluated. The proposed measurement method for low sinterability materials could accurately determine the sonic velocities of small-pellet-type samples, and the elastic properties were determined based on these velocities. The Young’s modulus of BZY10, BZY15, and BZY20 was 224, 218, and 209 GPa at 20 °C, respectively, and the values decreased as the yttrium concentration increased. At high temperatures (>20 °C), as the temperature increased, the Young’s and shear moduli decreased, whereas the bulk modulus and Poisson’s ratio increased. The Young’s and shear moduli varied nonlinearly with the temperature: The values decreased rapidly from 100 to 300 °C and gradually at temperatures beyond 400 °C. The Young’s modulus of BZY10, BZY15, and BZY20 was 137, 159, and 122 GPa at 500 °C, respectively, 30–40% smaller than the values at 20 °C. The influence of the temperature was larger than that of the change in the yttrium concentration.

Measurement of Young’s modulus and residual stress of thin SiC layers for MEMS high temperature applications

2012 ◽  
Vol 18 (7-8) ◽  
pp. 945-953 ◽  
Author(s):  
Oliver Pabst ◽  
Michael Schiffer ◽  
Ernst Obermeier ◽  
Tolga Tekin ◽  
Klaus Dieter Lang ◽  
...  
Keyword(s):  
Residual Stress ◽  
High Temperature ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Temperature Applications

Young’s modulus of zirconia at high temperature

2006 ◽  
Vol 41 (22) ◽  
pp. 7663-7666 ◽  
Author(s):  
E. Yeugo Fogaing ◽  
Y. Lorgouilloux ◽  
M. Huger ◽  
C. P. Gault
Keyword(s):  
High Temperature ◽  
Young’S Modulus ◽  
Young's Modulus

Young's modulus of RF-sputtered amorphous thin films in the SiO2-Y2O3 system at high temperature

1997 ◽  
Vol 293 (1-2) ◽  
pp. 144-148 ◽  
Author(s):  
T. Shinoda ◽  
N. Soga ◽  
T. Hanada ◽  
S. Tanabe
Keyword(s):  
Thin Films ◽  
High Temperature ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Amorphous Thin Films

High Temperature Mechanical Properties of Ni-YSZ Cermets for SOFC Anode

2010 ◽  
Author(s):  
Fumitada Iguchi ◽  
Hiromichi Kitahara ◽  
Hiroo Yugami
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Strain Diagram ◽  
Thermal Cycles ◽  
High Temperature Mechanical Properties ◽  
Sofc Anode ◽  
The Difference

The mechanical properties of Ni-YSZ cermets at high temperature in reduction atmosphere were evaluated by the four points bending method. We studied the influences of reduction and thermal cycles, i.e. a cycle from R.T. to 800°C, to flexural strength and Young’s modulus. The flexural strength of Ni-YSZ at room temperature was lower than that of NiO-YSZ by about 10 to 20% mainly caused by the increment of porosity. But, the flexural strength of Ni-YSZ at 800°C was drastically decreased by an half of that at R.T. In addition, the stress–strain diagram of Ni-YSZ at 800°C indicated that it showed weak ductility. The maximum observed strain was over 0.5% at 30MPa. On the contrary, NiO-YSZ showed only brittlely at 800°C. The difference was caused by Ni metal in the Ni-YSZ cermets. Therefore, it was expected that Ni-YSZ is easily deformed in operation, though residual stress between an anode and an electrolyte was low. The influence of thermal cycles to flexural strength and Young’s modulus was not observed clearly. At the same time, the differences of microstructure were not observed. Therefore, it was concluded that the cycle does not change mechanical properties significantly.

Sign in / Sign up

Export Citation Format

Share Document