scholarly journals Assessment of the global stability of three-limbed steel tube latticed column using finite element modelling

2021 ◽  
Vol 2045 (1) ◽  
pp. 012021
Author(s):  
Y D Fu ◽  
X Y Dai ◽  
H D Zhang ◽  
K G Shang
Keyword(s):  
Finite Element ◽  
Global Stability ◽  
Steel Tube ◽  
Buckling Analysis ◽  
Buckling Load ◽  
Elastic Buckling ◽  
Analysis Method ◽  
Element Analysis ◽  
Stability Performance ◽  
Geometric Defect

Abstract In order to study the stability performance of the three-limbed steel tube latticed column, the finite element numerical analysis method based on the structural stability theory is adopted. Firstly, the linear analysis of the three-limbed steel tube latticed column without diagonal lacing bar is carried out, and the calculation method of elastic buckling load considering the influence of shear deformation is obtained. Then, the elastic buckling analysis and elastoplastic buckling analysis three-limbed steel tube latticed column with diagonal lacing bar are carried out. The elastic buckling load and elastoplastic buckling load of three-limbed steel tube latticed column with diagonal lacing bar are studied when only the global initial geometric defects, only the member initial geometric defects, and both kinds of defects are considered at the same time. The results show that the direct finite element analysis method can be used to calculate the elastic buckling load of three-limbed steel tube latticed column with diagonal lacing bar, and the error is 6.67%. In the elastic analysis of three-limbed steel tube latticed column with diagonal lacing bar, the column global stability mainly depends on the global initial geometric defects, and the member initial geometric defect is negligible. And when two kinds of defects are applied at the same time, the structural buckling load is reduced by less than 0.20% compared to the global initial geometric defects. In the elastoplastic analysis, the column global stability is determined by both the global initial geometric defect and the member initial geometric defect. When both defects are applied at the same time, the structural buckling load decreases by less than 0.65% compared to the global initial geometric defect only, and 7.60% compared to the member initial geometric defects only. It can be concluded that there is little difference in the overall stability bearing capacity between the two kinds of defects.

Use of the Finite Element Analysis Method in Pedodontics

2018 ◽  
Vol 55 (4) ◽  
pp. 666-675
Author(s):  
Mihaela Tanase ◽  
Dan Florin Nitoi ◽  
Marina Melescanu Imre ◽  
Dorin Ionescu ◽  
Laura Raducu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Model ◽  
Analysis Method ◽  
Ansys Software ◽  
Concentrated Force ◽  
Element Analysis ◽  
Finite Element Analysis Method ◽  
The Finite Element Analysis ◽  
Solid Type

The purpose of this study was to determinate , using the Finite Element Analysis Method, the mechanical stress in a solid body , temporary molar restored with the self-curing GC material. The originality of our study consisted in using an accurate structural model and applying a concentrated force and a uniformly distributed pressure. Molar structure was meshed in a Solid Type 45 and the output data were obtained using the ANSYS software. The practical predictions can be made about the behavior of different restorations materials.

Buckling characteristics of cut-out borne composite stiffened hyperbolic paraboloid shell panel

2021 ◽  
pp. 146442072110058
Author(s):  
Sarmila Sahoo
Keyword(s):  
Finite Element ◽  
Orientation Angle ◽  
Buckling Load ◽  
Benchmark Problems ◽  
Hyperbolic Paraboloid ◽  
Element Analysis ◽  
Load Effect ◽  
Global Buckling ◽  
Fiber Orientation Angle ◽  
Shell Panel

The present study investigates buckling characteristics of cut-out borne stiffened hyperbolic paraboloid shell panel made of laminated composites using finite element analysis to evaluate the governing differential equations of global buckling of the structure. The finite element code is validated by solving benchmark problems from literature. Different parametric variations are studied to find the optimum panel buckling load. Laminations, boundary conditions, depth of stiffener and arrangement of stiffeners are found to influence the panel buckling load. Effect of different parameters like cut-out size, shell width to thickness ratio, degree of orthotropy and fiber orientation angle of the composite layers on buckling load are also studied. Parametric and comparative studies are conducted to analyze the buckling strength of composite hyperbolic paraboloid shell panel with cut-out.

Finite Element Analysis on Rack and Pinion of Roadheader

2013 ◽  
Vol 791-793 ◽  
pp. 718-721
Author(s):  
Man Man Xu ◽  
Yu Li ◽  
Sai Nan Xie ◽  
Qing Hua Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Spur Gear ◽  
Stress And Strain ◽  
Analysis Method ◽  
Element Analysis ◽  
The Road ◽  
The Finite Element Analysis ◽  
Gear Rack ◽  
Stress And Strain Distribution

To analyse the road-header rack and pinion by using the finite element analysis software COSMOS/WORKS. Compared to the traditional analytic calculation and numerical analysis method, it is more intuitively get 28 ° pressure angle spur gear rack meshing stress and strain distribution, which can rack and pinion improvements designed to provide scientific reference.

scholarly journals Finite Element Analysis on Behavior of Reinforced Hollow High Strength Concrete Filled Square Steel Tube Short Columns under Axial Compression

2021 ◽  
Vol 2101 (1) ◽  
pp. 012059
Author(s):  
Z J Yang ◽  
X Li ◽  
G C Li ◽  
S C Peng
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Strength Concrete ◽  
Mechanical Performance ◽  
Concrete Strength ◽  
High Strength ◽  
Steel Tube ◽  
Element Analysis ◽  
Steel Strength ◽  
Square Steel Tube

Abstract Hollow concrete-filled steel tubular (CFST) member is mainly adopted in power transmission and transformation structures, but when it is used in the superstructure with complex stress, the hollow CFST member has a low bearing capacity and is prone to brittle failure. To improve the mechanical performance of hollow CFST members, a new type of reinforced hollow high strength concrete-filled square steel tube (RHCFSST) was proposed, and its axial compression performance was researched. 18 finite element analysis (FEA) models of axially loaded RHCFSST stub columns were established through FEA software ABAQUS. The whole stress process of composite columns was studied, and parametric studies were carried out to analyze the mechanical performance of the member. Parameters of the steel strength, steel ratio, deformed bar and sandwich concrete strength were varied. Based on the simulation results, the stress process of members can be divided into four stages: elastic stage, elastoplastic stage, descending stage and gentle stage. With the increase of steel strength, steel ratio, the strength of sandwich concrete and the addition of deformed bars, the ultimate bearing capacity of members also increases. Additionally, the increment of those parameters will improve the ductility of the member, except for the sandwich concrete strength.

scholarly journals Finite Element Analysis of Foundation Pile Anchor Support System

2018 ◽  
Vol 1 (1) ◽  
Author(s):  
Zhenli Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Construction Projects ◽  
Analysis Method ◽  
Support Structure ◽  
Foundation Pit ◽  
Element Analysis ◽  
High Rise ◽  
Finite Element Analysis Method ◽  
Foundation Pile

With the continuous development of urban construction projects in HebeiProvince, the rise and development of high-rise buildings and undergroundengineering, the design and research of foundation pit support structure has become more and more important. The design of the foundation pit support structure directly affects the settlement and position changes of the building itself and the surrounding stratum. In this paper, the characteristics of foundation pit support are analyzed, and the related theories of finite element analysis method are introduced. Combined with the actual situation of Hebei Province, the finite element analysis method is used to simulate the construction method of foundation pile anchor support structure system. The design was analyzed and studied.

scholarly journals Finite element analysis of mechanical behavior of concrete-filled square steel tube short columns with inner I-shaped CFRP profiles subjected to bi-axial eccentric load

2018 ◽  
Author(s):  
Guochang Li ◽  
Zhichang Zhan ◽  
Zhijian Yang ◽  
Yu Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Compressive Strength ◽  
Steel Tube ◽  
Concrete Compressive Strength ◽  
Eccentric Load ◽  
Element Analysis ◽  
Composite Columns ◽  
Short Columns ◽  
Square Steel Tube

The concrete-filed square steel tube with inner I-shaped CFRP profiles short columns under bi-axial eccentric load were investigated by the finite element analysis software ABAQUS. The working mechanism of the composite columns which is under bi-axial eccentric load are investigated by using the stress distribution diagram of steel tube concrete and the I-shaped CFRP profiles. In this paper, the main parameters; eccentric ratio, steel ratio, steel yield strength, concrete compressive strength and CFRP distribution rate of the specimens were investigated to know the mechanical behavior of them. The interaction between the steel tube and the concrete interface at different characteristic points of the composite columns were analyzed. The results showed that the ultimate bearing capacity of the concrete-filed square steel tube with inner I-shaped CFRP profiles short columns under bi-axial eccentric load decrease with the increase of eccentric ratio, the ultimate bearing capacity of the composite columns increase with the increase of steel ratio, steel yield strength, concrete compressive strength and CFRP distribution rate. The contact pressure between the steel tube and the concrete decreased from the corner zone to the flat zone, and the contact pressure decreased from the mid-height cross section to other sections.

Sign in / Sign up

Export Citation Format

Share Document