scholarly journals Experimental analysis of the evaporation of a thin liquid film deposited on a capillary heated tube: estimation of the local heat transfer coefficient

2021 ◽  
Vol 2116 (1) ◽  
pp. 012110
Author(s):  
L Cattani ◽  
F Bozzoli ◽  
V Ayel ◽  
C Romestant ◽  
Y Bertin
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Liquid Film ◽  
Transfer Coefficient ◽  
Heat Conduction Problem ◽  
Thin Liquid Film ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Inverse Heat Conduction Problem ◽  
Two Phase

Abstract The aim of this work is to estimate the local heat flux and heat transfer coefficient for the case of evaporation of thin liquid film deposited on capillary heated channel: it plays a fundamental role in the two-phase heat transfer processes inside mini-channels. In the present analysis it is investigated a semi-infinite slug flow (one liquid slug followed by one single vapour bubble) in a heated capillary copper tube. The estimation procedure here adopted is based on the solution of the inverse heat conduction problem within the wall domain adopting, as input data, the temperature field on the external tube wall acquired by means of infrared thermography.

Experiments on Heat Transfer in a Thin Liquid Film Flowing Over a Rotating Disk

2004 ◽  
Vol 126 (2) ◽  
pp. 184-192 ◽  
Author(s):  
B. Ozar ◽  
B. M. Cetegen ◽  
A. Faghri
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Liquid Film ◽  
Transfer Coefficient ◽  
Liquid Flow ◽  
Thin Liquid Film ◽  
Local Heat Transfer ◽  
Disk Surface ◽  
Local Heat ◽  
Flow Rates

An experimental study of heat transfer into a thin liquid film on a rotating heated disk is described. Deionized water was introduced at the center of a heated, horizontal disk with a constant film thickness and uniform radial velocity. Radial distribution of the disk surface temperatures was measured using a thermocouple/slip ring arrangement. Experiments were performed for a range of liquid flow rates between 3.0 lpm and 15.0 lpm. The angular speed of the disk was varied from 0 rpm to 500 rpm. The local heat transfer coefficient was determined based on the heat flux supplied to the disk and the temperature difference between the measured disk surface temperature and the liquid entrance temperature onto the disk. The local heat transfer coefficient was seen to increase with increasing flow rate as well as increasing angular velocity of the disk. Effect of rotation on heat transfer was largest for the lower liquid flow rates with the effect gradually decreasing with increasing liquid flow rates. Semi-empirical correlations are presented in this study for the local and average Nusselt numbers.

scholarly journals ENHANCEMENT THE HEAT TRANSFER FOR TWO-PHASE FLOW THROUGH A RECTANGULAR RIBBED VERTICAL CHANNEL

2018 ◽  
Vol 18 (1) ◽  
pp. 92-109
Author(s):  
Riyadh S Al-Turaihi ◽  
Doaa F Kareem
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Two Phase Flow ◽  
Vertical Channel ◽  
Numerical Data ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Phase Flow ◽  
Two Phase

 The heat transfer coefficient and temperature distribution of two phase flow (water, air)in rectangular ribbed vertical channel was investigated experimentally and numerically inthis work for different values of water and air superficial velocities (0.0421, 0.0842, 0.1158,0.1474 and 0.1684 m/s) and (1.0964, 1.425, 1.644, 1.864 and 2.193 m/s), respectively, atconstant heat flux (120 W). The distribution of temperature along the channel wasphotographed using thermal camera and compared with images for the correspondingcontours which found numerically. The experimental results of heat transfer coefficientcompared with computational fluid dynamics model simulated by Ansys fluent 15.0. Agood agreement has been found between the experimental and numerical data, where thepercentage deviation between the experimental and the numerical results is (1% - 6% ). Theresults showed that, the local heat transfer coefficient increased by adding ribs, it alsoincreased as the velocity of the flow increased.

ENHANCEMENT THE HEAT TRANSFER FOR TWO-PHASE FLOW THROUGH A RECTANGULAR RIBBED VERTICAL CHANNEL

2018 ◽  
Vol 18 (1) ◽  
pp. 92-109
Author(s):  
Riyadh S Al-Turaihi ◽  
Doaa F Kareem
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Two Phase Flow ◽  
Vertical Channel ◽  
Numerical Data ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Phase Flow ◽  
Two Phase

The heat transfer coefficient and temperature distribution of two phase flow (water, air)in rectangular ribbed vertical channel was investigated experimentally and numerically inthis work for different values of water and air superficial velocities (0.0421, 0.0842, 0.1158,0.1474 and 0.1684 m/s) and (1.0964, 1.425, 1.644, 1.864 and 2.193 m/s), respectively, atconstant heat flux (120 W). The distribution of temperature along the channel wasphotographed using thermal camera and compared with images for the correspondingcontours which found numerically. The experimental results of heat transfer coefficientcompared with computational fluid dynamics model simulated by Ansys fluent 15.0. Agood agreement has been found between the experimental and numerical data, where thepercentage deviation between the experimental and the numerical results is (1% - 6% ). Theresults showed that, the local heat transfer coefficient increased by adding ribs, it alsoincreased as the velocity of the flow increased.

A Study on Gas–Liquid Film Thicknesses and Heat Transfer Characteristics of Vapor–Gas Condensation Outside a Horizontal Tube

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Huijun Li ◽  
Wenping Peng
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Liquid Film ◽  
Transfer Coefficient ◽  
Local Heat Transfer ◽  
Horizontal Tube ◽  
Local Heat ◽  
Condensation Heat Transfer ◽  
Gas Condensation ◽  
Noncondensable Gas

Noncondensable gases deteriorate heat transfer in the condensation process. It is therefore necessary to study vapor–gas condensation heat transfer process and analyze main factors influencing the process. Based on the double-film theory and the Prandtl boundary layer theory, this investigation developed a mathematical model of gas–liquid film thicknesses and local heat transfer coefficient for studying laminar film condensation in the presence of noncondensable gas over a horizontal tube. Induced velocity in the gas film, gas–liquid interfacial shear stress, and pressure gradient were considered in the study. Importantly, gas–liquid film separations were analyzed in depth in this paper. It obtained the distributions of gas–liquid film thicknesses, local heat transfer coefficient, condensate mass flux, and gas–liquid interfacial temperature along the tube surface, and analyzed the influences of bulk velocity, total pressure, bulk mass concentration of noncondensable gas and wall temperature on them, providing a theoretical guidance for understanding and enhancing vapor–gas condensation heat transfer. Gas film thickness and gas–liquid film separations have certain effects on vapor–gas condensation heat transfer. The average dimensionless heat transfer coefficients are in agreement with the data from related literatures.

The Pressure Drop and Heat Transfer of Flow in Zigzag Micro-Channel With Micro-Orifice

2010 ◽  
Author(s):  
Chengyun Wu ◽  
Hongbo Xu ◽  
Changqing Tian
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Micro Channel ◽  
Two Phase ◽  
Boiling Flow ◽  
Phase Liquid

In this paper, the experimental investigation on friction factor and heat transfer of single phase liquid flow and two-phase boiling flow in single zigzag micro-channel with micro-orifice at inlet has been conducted. The dimension of the micro-orifice is 1mm×0.227mm×0.25mm. The experiment was conducted in copper rectangle zigzag micro-channel with the hydraulic diameter of 0.321mm and the length of 29 mm. The experimental results of friction factor and heat transfer coefficient were provided and the effect of the micro-orifice was discussed. It was found that the friction factor of flow in zigzag micro-channel deviated largely from the predictive value in the laminar flow, while it coincided well with the correlation for turbulent flow. In addition, the variation of local heat transfer coefficient showed that the inlet restrictor has significant effect on heat transfer of boiling flow in micro-channel.

Sign in / Sign up

Export Citation Format

Share Document