scholarly journals Effects on Vibration and Surface Roughness in High Speed Micro End-Milling of Inconel 718 with Minimum Quantity Lubrication

2017 ◽  
Vol 184 ◽  
pp. 012037 ◽  
Author(s):  
Mohamed Abd Rahman ◽  
Mohammad Yeakub Ali ◽  
Amir Saddam Khairuddin
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
High Speed ◽  
End Milling ◽  
Minimum Quantity Lubrication ◽  
Minimum Quantity ◽  
Micro End Milling

Experimental Study on Micro End-Milling Process of Ti-6AL-4V Using Nanofluid Minimum Quantity Lubrication (MQL)

2014 ◽  
Author(s):  
Dae Hoon Kim ◽  
Pil-Ho Lee ◽  
Jung Sub Kim ◽  
Hyungpil Moon ◽  
Sang Won Lee
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
End Milling ◽  
Minimum Quantity Lubrication ◽  
Milling Process ◽  
Minimum Quantity ◽  
Nanofluid Minimum Quantity Lubrication ◽  
Micro End Milling ◽  
Milling Forces ◽  
End Milling Process

This paper investigates the characteristics of micro end-milling process of titanium alloy (Ti-6AL-4V) using nanofluid minimum quantity lubrication (MQL). A series of micro end-milling experiments are conducted in the meso-scale machine tool system, and milling forces, burr formations, surface roughness, and tool wear are observed and analyzed according to varying feed per tooth and lubrication conditions. The experimental results show that MQL and nanofluid MQL with nanodiamond particles can be effective to reduce milling forces, burrs and surface roughness during micro end-milling of titanium alloy. In particular, it is demonstrated that smaller size of nanodiamond particles — 35 nm — can be more effective to decrease burrs and surface roughness in the case of nanofluid MQL micro end-milling.

Investigation of Surface Roughness and Material Removal Rate for High Speed Micro End Milling on PMMA

2015 ◽  
Vol 1115 ◽  
pp. 12-15
Author(s):  
Nur Atiqah ◽  
Mohammad Yeakub Ali ◽  
Abdul Rahman Mohamed ◽  
Md. Sazzad Hossein Chowdhury
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
High Speed ◽  
End Milling ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Micro End Milling

Micro end milling is one of the most important micromachining process and widely used for producing miniaturized components with high accuracy and surface finish. This paper present the influence of three micro end milling process parameters; spindle speed, feed rate, and depth of cut on surface roughness (Ra) and material removal rate (MRR). The machining was performed using multi-process micro machine tools (DT-110 Mikrotools Inc., Singapore) with poly methyl methacrylate (PMMA) as the workpiece and tungsten carbide as its tool. To develop the mathematical model for the responses in high speed micro end milling machining, Taguchi design has been used to design the experiment by using the orthogonal array of three levels L18 (21×37). The developed models were used for multiple response optimizations by desirability function approach to obtain minimum Ra and maximum MRR. The optimized values of Ra and MRR were 128.24 nm, and 0.0463 mg/min, respectively obtained at spindle speed of 30000 rpm, feed rate of 2.65 mm/min, and depth of cut of 40 μm. The analysis of variance revealed that spindle speeds are the most influential parameters on Ra. The optimization of MRR is mostly influence by feed rate. Keywords:Micromilling,surfaceroughness,MRR,PMMA

scholarly journals Measurement and Analysis of Surface Roughness in WS2 Solid Lubricant Assisted Minimum Quantity Lubrication (MQL) Turning of Inconel 718

Procedia CIRP ◽  
2016 ◽  
Vol 40 ◽  
pp. 138-143 ◽  
Author(s):  
Uma Maheshwera Reddy Paturi ◽  
Yesu Ratnam Maddu ◽  
Ramalinga Reddy Maruri ◽  
Suresh Kumar Reddy Narala
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
Solid Lubricant ◽  
Minimum Quantity Lubrication ◽  
Minimum Quantity ◽  
Measurement And Analysis

Application of tri-hybridized carbonaceous nanocutting fluids in an end milling operation by the minimum quantity lubrication technique

2021 ◽  
pp. 135065012110438
Author(s):  
S. Vignesh ◽  
U. Mohammed Iqbal
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
End Milling ◽  
Hexagonal Boron Nitride ◽  
Coconut Oil ◽  
Minimum Quantity Lubrication ◽  
Work Piece ◽  
Cutting Fluids ◽  
Minimum Quantity ◽  
Milling Operations

This paper is concentrated on the exploration of carbonaceous nanocutting fluids with the concept of tri-hybridization with improved lubricative and cooling properties by using multi-walled carbon nanotubes, hexagonal boron nitride , and graphene nanoparticles with neat cold-pressed coconut oil in a fixed volumetric proportion. The rheological properties of the nanofluids were studied to assess their performance in real-time end milling operations using an AA7075 work piece on a CNC lathe machine under a minimum quantity lubrication environment. At the outset, the carbonaceous nanofluids gave good performance when compared to conventional cutting fluids. Furthermore, the surfaces of the tribo-pairs and the chips formed were analyzed using a profilometer and high-end microscopes. The results obtained from the experiments confirm that the tri-hybridized carbonaceous nanolubricant has reduced the cutting force, tool wear, and surface roughness when correlated to monotype nanofluids. The scanning electron microscope images of the surface and tool were studied and it was found that the surface quality was maintained while end milling with tri-hybridized carbonaceous nanofluid. Improvement of ∼17%, 20% and 25% in cutting forces, surface roughness and tool wear was found in tri-hybrid fluid when compared to other fluids. Thus, the present work indicates that the addition of carbon-based nanoparticles with coconut oil has offered better performance and is found to be a credible alternative to existing conventional cutting fluids.

Sign in / Sign up

Export Citation Format

Share Document