scholarly journals A numerical-experimental analysis of qualification assessment for mono-block plasma-facing component with flat heat sink

2021 ◽  
Author(s):  
Ji Hwan Lim ◽  
Minkyu Park
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Flow Boiling ◽  
Heat Removal ◽  
Nucleate Boiling ◽  
Error Rates ◽  
High Heat Flux ◽  
Boiling Regime ◽  
Plasma Facing Component ◽  
Heat Transfer Correlations

Abstract The heat removal capacity of a flat heat sink was studied using subcooled flow boiling experiments, to address the thermal peaking problem. Based on the Bowring criteria, the boiling curve is divided into a partially developed nucleate boiling regime (PDB) and fully developed nucleate boiling regime (FDB), and the existing heat transfer correlations for each flow regime are evaluated. In the PDB regime, the Baburajan correlation exhibited the highest prediction rate with an average error rate of 10.92%; however, the FDB regime heat transfer correlations exhibited high error rates at very high heat flux conditions. Therefore, the authors developed a new FDB correlation using the artificial intelligence technique by correlating the bubble agitation effect, which is a mechanism of the FDB regime, and then, evaluated the qualification assessment on this basis. The mono-block plasma-facing component with a flat heat sink was found to meet all criteria (except #1.2, shutdown plasma ratcheting), and to succeed in the actual fabrication.

Study on onset of nucleate boiling with screw tube for fusion reactor application

2021 ◽  
Author(s):  
Ji Hwan Lim ◽  
Minkyu Park
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Transfer Mechanism ◽  
High Heat Flux ◽  
Heat Transfer Mechanism ◽  
System Parameters ◽  
Smooth Tubes

Abstract The onset of nucleate boiling (ONB) is the point at which the heat transfer mechanism in fluids changes and is one of the thermo-hydraulic factors that must be considered when establishing a cooling system operation strategy. Because the high heat flux of several MW/m2, which is loaded within a tokamak, is applied under a one-side heating condition, it is necessary to determine a correlative relation that can predict ONB under special heating conditions. In this study, the ONB of a one-side-heated screw tube was experimentally analyzed via a subcooled flow boiling experiment. The helical nut structure of the screw tube flow path wall allows for improved heat transfer performance relative to smooth tubes, providing a screw tube with a 53.98% higher ONB than a smooth tube. The effects of the system parameters on the ONB heat flux were analyzed based on the changes in the heat transfer mechanism, with the results indicating that the flow rate and degree of subcooling are proportional to the ONB heat flux because increasing these factors improves the forced convection heat transfer and increases the condensation rate, respectively. However, it was observed that the liquid surface tension and latent heat decrease as the pressure increases, leading to a decrease in the ONB heat flux. An evaluation of the predictive performance of existing ONB correlations revealed that most have high error rates because they were developed based on ONB experiments on micro-channels or smooth tubes and not under one-side high heat load conditions. To address this, we used dimensional analysis based on Python code to develop new ONB correlations that reflect the influence of system parameters.

A Comparative Numerical Study on Two-Phase Boiling Fluid Flow and Heat Transfer in the Microchannel Heat Sink With Different Manifold Arrangements

2020 ◽  
Author(s):  
Yang Luo ◽  
Jingzhi Zhang ◽  
Wei Li
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
Numerical Study ◽  
Flow Boiling ◽  
High Surface ◽  
Volume Ratio ◽  
High Heat Flux ◽  
Two Phase ◽  
Flow Maldistribution

Abstract The manifold microchannel (MMC) heat sink system has been widely used in high-heat-flux chip thermal management due to its high surface-to-volume ratio. Two-phase, three-dimensional numerical methods for subcooled flow boiling have been developed using a self-programming solver based on OpenFOAM. Four different types of manifold arrangements (Z-type, C-type, H-type and U-type) have been investigated at a fixed operational condition. The numerical results evaluate the effects of flow maldistribution caused by different manifold configurations. Before simulating the two-phase boiling flow in MIMC metamodels, single-phase liquid flow fields are performed at first to compare the flow maldistribution in microchannels. It can be concluded from the flow patterns that H-type and U-type manifolds provide a more even and a lower microchannel void fraction, which is conducive to improving the temperature uniformity and decreasing the effective thermal resistance. The simulation results also show that the wall temperature difference of H-type (0.471 K) is only about 10% of the Z-type (4.683 K). In addition, the U-type manifold configuration show the lowest average pressure drop at the inlet and outlet of the MIMC metamodel domain. However, H-type manifold also shows an impressive 59.9% decrease in pressure loss. Results indicate that both the H-type and the U-type manifolds for flow boiling in microchannels are recommended due to their better heat transfer performance and lower pressure drop when compared with Z-type and C-type.

Flow Boiling Enhancement in Microchannels With Diffusion Bonded Wire Mesh

2007 ◽  
Author(s):  
Hailei Wang ◽  
Richard Peterson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Wire Mesh ◽  
Working Fluid ◽  
High Heat Flux ◽  
Vapor Quality ◽  
Heating Wall

Flow boiling and heat transfer enhancement in four parallel microchannels using a dielectric working fluid, HFE 7000, was investigated. Each channel was 1000 μm wide and 510 μm high. A unique channel surface enhancement technique via diffusion bonding a layer of conductive fine wire mesh onto the heating wall was developed. According to the obtained flow boiling curves for both the bare and mesh channels, the amount of wall superheat was significantly reduced for the mesh channel at all stream-wise locations. This indicated that the nucleate boiling in the mesh channel was enhanced due to the increase of nucleation sites the mesh introduced. Both the nucleate boiling dominated and convective evaporation dominated regimes were identified. In addition, the overall trend for the flow boiling heat transfer coefficient, with respect to vapor quality, was increasing until the vapor quality reached approximately 0.4. The critical heat flux (CHF) for the mesh channel was also significantly higher than that of the bare channel in the low vapor quality region. Due to the fact of how the mesh was incorporated into the channels, no pressure drop penalty was identified for the mesh channels. Potential applications for this kind of mesh channel include high heat-flux electronic cooling systems and various energy conversion systems.

Numerical Investigation of Flow Boiling in a Manifold Microchannel Heat Sink With Conjugate Heat Transfer

2019 ◽  
Author(s):  
Zhichuan Sun ◽  
Yang Luo ◽  
Junye Li ◽  
Wei Li ◽  
Jingzhi Zhang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Numerical Investigation ◽  
Heat Sink ◽  
Conjugate Heat Transfer ◽  
Flow Boiling ◽  
High Heat Flux ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Boiling Process ◽  
Manifold Microchannel

Abstract The manifold microchannel heat sink receives an increasing number of attention lately due to its high heat flux dissipation. Numerical investigation of boiling phenomena in manifold microchannel (MMC) heat sinks remains a challenge due to the complexity of fluid route and the limitation of numerical accuracy. In this study, a computational fluid dynamics (CFD) approach including subcooled two-phase flow boiling process and conjugate heat transfer effect is performed using a MMC unit cell model. Different from steady-state single phase prediction in MMC heat sink, this type of modeling allows for the transient simulation for two-phase interface evolution during the boiling process. A validation case is conducted to validate the heat transfer phenomenon among three phases. Besides, this model is used for the assessment of the manifold dimensions in terms of inlet and outlet widths at the mass flux of 1300 kg/m2·s. With different ratios of inlet-to-outlet area, the thermal resistances remain nearly stable.

Boiling Heat Transfer Performance in a Spiraling Radial Inflow Microchannel Cold Plate

2015 ◽  
Author(s):  
Maritza Ruiz ◽  
Claire M. Kunkle ◽  
Jorge Padilla ◽  
Van P. Carey
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Contact Angles ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Maximum Heat ◽  
Flow Boiling Heat Transfer

This study presents an experimental exploration of flow boiling heat transfer in a spiraling radial inflow microchannel heat sink. The effect of surface wettability, fluid subcooling levels, and mass fluxes are considered in this type of heat sink for use in applications with high fluxes up to 300 W/cm2. The design of the heat sink provides an inward radial swirl flow between parallel, coaxial disks that form a microchannel of 300 μm and 1 cm radius with a single inlet and a single outlet. The channel is heated on one side through a copper conducting surface, while the opposite side is essentially adiabatic to simulate a heat sink scenario for electronics cooling. Flow boiling heat transfer and pressure drop data were obtained for this heat sink device using water at near atmospheric pressure as the working fluid for inlet subcooling levels from 20 to 81°C and mean mass flux levels ranging from 184 to 716 kg/m2s. To explore the effects of varying surface wetting, experiments were conducted with two different heated surfaces. One was a clean, machined copper surface with water equilibrium contact angles in the range of 14–40°, typical of common metal surfaces. The other was a surface coated with zinc oxide nanostructures that are superhydrophilic with equilibrium contact angles measured below 10°. During boiling, increased wettability resulted in quicker rewetting and smaller bubble departure diameter as indicated by reduced temperature oscillations during boiling and achieving higher maximum heat flux without dryout. Reducing inlet subcooling levels was also found to reduce the magnitude of oscillations in the oscillatory boiling regime. The highest heat transfer coefficients were seen in fully developed boiling with low subcooling levels as a result of heat transfer being dominated by nucleate boiling. The highest heat fluxes achieved were during partial subcooled flow boiling at 300 W/cm2 with an average surface temperature of 134 °C and requiring a pumping power to heat rate ratio of 0.01%. The hydrophilic surface retained wettability after a series of boiling tests. Recommendations for use of this heat sink design in high flux applications is also discussed.

Enhanced Flow Boiling Over Open Microchannels With Uniform and Tapered Gap Manifolds

2013 ◽  
Vol 135 (6) ◽  
Author(s):  
Satish G. Kandlikar ◽  
Theodore Widger ◽  
Ankit Kalani ◽  
Valentina Mejia
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Performance ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

Flow boiling in microchannels has been extensively studied in the past decade. Instabilities, low critical heat flux (CHF) values, and low heat transfer coefficients have been identified as the major shortcomings preventing its implementation in practical high heat flux removal systems. A novel open microchannel design with uniform and tapered manifolds (OMM) is presented to provide stable and highly enhanced heat transfer performance. The effects of the gap height and flow rate on the heat transfer performance have been experimentally studied with water. The critical heat fluxes (CHFs) and heat transfer coefficients obtained with the OMM are significantly higher than the values reported by previous researchers for flow boiling with water in microchannels. A record heat flux of 506 W/cm2 with a wall superheat of 26.2 °C was obtained for a gap size of 0.127 mm. The CHF was not reached due to heater power limitation in the current design. A maximum effective heat transfer coefficient of 290,000 W/m2 °C was obtained at an intermediate heat flux of 319 W/cm2 with a gap of 0.254 mm at 225 mL/min. The flow boiling heat transfer was found to be insensitive to flow rates between 40–333 mL/min and gap sizes between 0.127–1.016 mm, indicating the dominance of nucleate boiling. The OMM geometry is promising to provide exceptional performance that is particularly attractive in meeting the challenges of high heat flux removal in electronics cooling applications.

An Experimental Investigation of Sub-Cooled Flow Boiling in Hypervapotron Cooling Configuration

2004 ◽  
Author(s):  
Peipei Chen ◽  
Barclay G. Jones ◽  
Ty A. Newell
Keyword(s):  
Heat Transfer ◽  
High Speed ◽  
Flow Boiling ◽  
Experimental Studies ◽  
Nucleate Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Subcooled Boiling ◽  
Reduced Pressure

This work reports on experimental studies to visualize nucleate boiling on the enhanced heat transfer surface of the hypervapotron for with application in the International Thermonuclear Experiment Reactor [ITER]. This research uses the simulant fluid Freon (R134A) instead of prototypic water to model the system performance. This results in much lower thermophysical conditions to represent the prototypic phenomena. By using reduced pressure, temperatures, etc, based on the critical physical properties of both working fluids, Freon and water, the dramatic drop in the level of these quantities with Freon allows the use of modest test conditions. The experiment was conducted for both saturated and subcooled boiling with different heat fluxes (from 50 to 300 kW/m2). A comparison of the heat transfer performance of finned structures and flat surfaces were examined under particular fluid conditions. The uniqueness of this work is the visualization method that allows direct observation of the subcooled boiling process of the Hypervapotron surfaces. Working with a high speed (12,000 frames per second), high fidelity digital camera with variable magnifications (from 1×–25×), the sub-cooled boiling phenomena was observed in detail. A major conclusion of this work is the existence of two separate zones linked to different energy removal efficiency in hypervapotron. Under high heat flux condition, enhanced boiling heat transfer (about 20–30% higher than flat surface) was observed for hypervapotron effect, while saturated boiling happened in the cavity, and a large portion of the region was vapor filled. The process of vapor bubble rotation in the slot appeared to be helpful to enhance energy transfer, as evidenced by an improved wetting condition on the heating surfaces.

scholarly journals Boiling Heat Transfer Performance of Parallel Porous Microchannels

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2970
Author(s):  
Donghui Zhang ◽  
Haiyang Xu ◽  
Yi Chen ◽  
Leiqing Wang ◽  
Jian Qu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Boiling Process

Flow boiling in microporous layers has attracted a great deal of attention in the enhanced heat transfer field due to its high heat dissipation potential. In this study, flow boiling experiments were performed on both porous microchannels and a copper-based microchannel, using water as the coolant. As the heat flux was less than 80 W/cm2, the porous microchannels presented significantly higher boiling heat transfer coefficients than the copper-based microchannel. This was closely associated with the promotion of the nucleation site density of the porous coating. With the further increase in heat flux, the heat transfer coefficients of the porous microchannels were close to those of the copper-based sample. The boiling process in the porous microchannel was found to be dominated by the nucleate boiling mechanism from low to moderate heat flux (<80 W/cm2).This switched to the convection boiling mode at high heat flux. The porous samples were able to mitigate flow instability greatly. A visual observation revealed that porous microchannels could suppress the flow fluctuation due to the establishment of a stable nucleate boiling process. Porous microchannels showed no advantage over the copper-based sample in the critical heat flux. The optimal thickness-to-particle-size ratio (δ/d) for the porous microchannel was confirmed to be between 2–5. In this range, the maximum enhanced effect on boiling heat transfer could be achieved.

scholarly journals High heat flux flow boiling of refrigerant R236fa in parallel microchannels

2019 ◽  
Vol 196 ◽  
pp. 00062
Author(s):  
Vladimir Kuznetsov ◽  
Alisher Shamirzaev ◽  
Alexander Mordovskoy
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Flux Flow ◽  
Microchannel Heat Exchanger ◽  
Parallel Microchannels

This paper presents the results of an experimental study of the heat transfer during flow boiling of refrigerant R236fa in a horizontal microchannel heat sink. The experiments were performed using closed loop that re-circulates coolant. Microchannel heat exchanger that contains two microchannels with 2x0.4 mm cross-section was used as the test section. The dependence of average heat flux on wall superheat and critical heat flux were measured in the range of mass fluxes from 600 to 1600 kg/m2s and in the range of heat fluxes from 5 to 120 W/cm2. For heat flux greater than 60 W/cm2, nucleate boiling suppression has significant effect on the flow boiling heat transfer, and this leads to decrease of the heat transfer coefficient with heat flux grows.

A Review of High-Heat-Flux Heat Removal Technologies

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
M. A. Ebadian ◽  
C. X. Lin
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Heat Removal ◽  
High Heat ◽  
High Heat Flux ◽  
Phase Flow ◽  
Two Phase ◽  
Recent Developments ◽  
Removal Technologies

In recent years, high-heat-flux cooling techniques have received great attention from researchers around the world due to its importance in thermal management of both commercial and defense high-power electronic devices. Although impressive progress has been made during the last few decades, high-heat-flux removal still largely remains as a challenging subject that needs further exploration and study. In this paper, we have reviewed recent developments in several high-heat-flux heat removal techniques, including microchannels, jet impingements, sprays, wettability effects, and piezoelectrically driven droplets. High-heat-flux removal can be achieved effectively by either single-phase flow or two-phase flow boiling heat transfer. Better understandings of the underlying heat transfer mechanisms for performance improvement are discussed.

Sign in / Sign up

Export Citation Format

Share Document