Organic Electronics

Author(s):  
Stephen R. Forrest

Organic electronics is a platform for very low cost and high performance optoelectronic and electronic devices that cover large areas, are lightweight, and can be both flexible and conformable to irregularly shaped surfaces such as foldable smart phones. Organics are at the core of the global organic light emitting device (OLED) display industry, and also having use in efficient lighting sources, solar cells, and thin film transistors useful in medical and a range of other sensing, memory and logic applications. This book introduces the theoretical foundations and practical realization of devices in organic electronics. It is a product of both one and two semester courses that have been taught over a period of more than two decades. The target audiences are students at all levels of graduate studies, highly motivated senior undergraduates, and practicing engineers and scientists. The book is divided into two sections. Part I, Foundations, lays down the fundamental principles of the field of organic electronics. It is assumed that the reader has an elementary knowledge of quantum mechanics, and electricity and magnetism. Background knowledge of organic chemistry is not required. Part II, Applications, focuses on organic electronic devices. It begins with a discussion of organic thin film deposition and patterning, followed by chapters on organic light emitters, detectors, and thin film transistors. The last chapter describes several devices and phenomena that are not covered in the previous chapters, since they lie outside of the current mainstream of the field, but are nevertheless important.

2021 ◽  
Vol 16 (2) ◽  
pp. 1-11
Author(s):  
José Enrique Eirez Izquierdo ◽  
José Diogo da Silva Oliveira ◽  
Vinicius Augusto Machado Nogueira ◽  
Dennis Cabrera García ◽  
Marco Roberto Cavallari ◽  
...  

This work is focused on the bias stress (BS) effects in Organic Thin-Film Transistors (OTFTs) from poly(2,5-bis(3-alkylthiophen-2-yl)thieno[3,2-b]thiophene) (PBTTT-C14) on both highly-doped Si and glass substrates. While the former had a thermally-grown SiO2 dielectric, the latter demanded an alternative dielectric that should be capable to withstand bottom contact lithography, as well as semiconducting thin-film deposition. In addition, it should represent one more step towards flexible electronics. In order to do that, poly(4-vinylphenol) (PVP) was blended to poly(melamine-co-formaldehyde) methylated (PMF). OTFTs on glass with a cross-linked polymer dielectric had a charge carrier mobility (μ) of 4.0x10-4 cm2/Vs, threshold voltage (VT) of 18 V, current modulation (ION/OFF) higher than 1x102, and subthreshold slope (SS) of -7.7 V/dec. A negative BS shifted VT towards negative values and produced an increase in ION/OFF. A positive BS, on the other hand, produced the opposite effect only for OTFTs on Si. This is believed to be due to a higher trapping at the PVP:PMF interface with PBTTT-C14. Modeling the device current along time by a stretched exponential provided shorter time constants of ca. 105 s and higher exponents of 0.7–0.9 for devices on glass. Due to the presence of increased BS effects, the application of organic TFTs based on PVP:PMF as flexible sensors will require compensating circuits, lower voltages or less measurements in time. Alternatively, BS effects could be reduced by a dielectric surface treatment.


2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Kwon-Yong Shin ◽  
Mingyu Kang ◽  
Kwan Hyun Cho ◽  
Kyung-Tae Kang ◽  
Sang-Ho Lee

AbstractUniform deposition across large areas of an organic layer is one of the challenges for the industrial application of solution-based organic light‐emitting diode (OLED). In this paper, we propose an organic thin film deposition method for OLED using a micro multi-nozzle jet coating process. The developed micro multi-nozzle jet head consists of eighteen nozzles (100 μm diameter), a side suction line, inlets, and a nozzle protection outer hole. To demonstrate organic thin film deposition for OLED lighting device fabrication, a poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) solution was used as a hole injection layer (HIL). Thickness uniformity of the PEDOT:PSS thin film was analyzed by regulating the jetting pressure. Through single-path coating of twelve successive stable column-jet flows, PEDOT:PSS organic film of 26 mm width was coated on an ITO substrate at 1 m/s head speed. The PEDOT:PSS thin film of 24.25 ± 1.55 nm (CV = 6.39%) thickness was obtained by the proposed coating method. For the feasibility test, OLED lighting devices with emission areas of 20 mm × 20 mm and 70 mm × 70 mm were successfully fabricated using PEDOT:PSS films deposited by a micro multi-nozzle jet coating method.


2010 ◽  
Vol 130 (2) ◽  
pp. 161-166
Author(s):  
Yoshinori Ishikawa ◽  
Yasuo Wada ◽  
Toru Toyabe ◽  
Ken Tsutsui

2010 ◽  
Vol 3 (10) ◽  
pp. 101601 ◽  
Author(s):  
Yoshinori Horii ◽  
Koichi Sakaguchi ◽  
Masayuki Chikamatsu ◽  
Reiko Azumi ◽  
Kiyoshi Yase ◽  
...  

2019 ◽  
Vol 11 (10) ◽  
pp. 10089-10098 ◽  
Author(s):  
Hang Wang ◽  
Jun Huang ◽  
Mohammad Afsar Uddin ◽  
Bin Liu ◽  
Peng Chen ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document