Determination of apparent earth pressure diagram for anchored walls in c–φ soil with surcharge

2020 ◽  
Vol 17 (4) ◽  
pp. 481-489
Author(s):  
Seyyed Pouya Alavinezhad ◽  
Hadi Shahir
Keyword(s):  
Retaining Wall ◽  
Ground Surface ◽  
Earth Pressure ◽  
Ground Level ◽  
Content Type ◽  
Lateral Earth Pressure ◽  
The Earth ◽  
Real Distribution ◽  
Strain Modeling

Purpose The purpose of this study is to present a diagram for the lateral earth pressure of c–φ soils exerted on anchored walls in presence of surcharge. Design/methodology/approach To this end, two-dimensional plane strain modeling of anchored wall was carried out in Plaxis software. To validate the numerical model, two excavations with different specifications were simulated and the model results were compared with the available results. Subsequently, a parametric analysis was done and based on its results, a diagram was proposed for the lateral earth pressure of c–φ soils including the surcharge effects. Findings The proposed diagram without the surcharge and cohesion effects is a trapezoidal with zero value at the ground surface that is linearly approaching the apparent earth pressure of sand according to Terzaghi and Peck (1967) at 0.1H (H: wall height). The surcharge and cohesion effects at the ground level is 4 Ka*q and 0, respectively, and below 0.1H, they are treated as the same way for lateral earth pressure of a retaining wall. It should be emphasized that the apparent pressure diagram for design does not resemble the real distribution of earth pressure against the wall and it is for calculating the values of the anchors loads. Originality/value The available diagrams to determine the earth pressure exerted on the anchored walls are related to sandy or clayey soils and do not take the presence of surcharge into account. Thus, the proposed diagram is quite original and different from the previous ones.

Analytical solution for active pressure of narrow backfills considering arching effect

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Sahar Ghobadi ◽  
Hadi Shahir
Keyword(s):  
Analytical Solution ◽  
Retaining Wall ◽  
Earth Pressure ◽  
Back Surface ◽  
Active Earth Pressure ◽  
Soil Pressure ◽  
Principal Stresses ◽  
Content Type ◽  
Arching Effect ◽  
Lateral Earth Pressure

Purpose The purpose of this paper is to study the distribution of active earth pressure in retaining walls with narrow cohesion less backfill considering arching effects. Design/methodology/approach To this end, the approach of principal stresses rotation was used to consider the arching effects. Findings According to the presented formulation, the active soil pressure distribution is nonlinear with zero value at the wall base. The proposed formulation implies that by increasing the frictional forces at both sides of the backfill, the arching effect is increased and so, the lateral earth pressure on the retaining wall is decreased. Also, by narrowing the backfill space, the lateral earth pressure is extremely decreased. Originality/value A comprehensive analytical solution for the active earth pressure of narrow backfills is presented, such that the effects of the surcharge and the characteristics of the stable back surface are considered. The magnitude and height of the application of lateral active force are also derived.

scholarly journals Lateral Earth Pressure behind Walls Rotating about Base considering Arching Effects

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Dong Li ◽  
Wei Wang ◽  
Qichang Zhang
Keyword(s):  
Conversion Factor ◽  
Retaining Wall ◽  
Earth Pressure ◽  
Soil Mass ◽  
Shear Stresses ◽  
Key Factors ◽  
Lateral Earth Pressure ◽  
The Earth ◽  
Common Effect ◽  
The Common

In field, the earth pressure on a retaining wall is the common effect of kinds of factors. To figure out how key factors act, it has taken into account the arching effects together with the contribution from the mode of displacement of a wall to calculate earth pressure in the proposed method. Based on Mohr circle, a conversion factor is introduced to determine the shear stresses between artificial slices in soil mass. In the light of this basis, a modified differential slices solution is presented for calculation of active earth pressure on a retaining wall. Comparisons show that the result of proposed method is identical to observations from model tests in prediction of lateral pressures for walls rotating about the base.

Estimation of the Passive Earth Pressure with Inclined Cohesive Backfills: The Effect of Intermediate Principal Stress is Considered

2010 ◽  
Vol 168-170 ◽  
pp. 1370-1376
Author(s):  
We Long Yu ◽  
Jian Zhang ◽  
Xiu Hua Sun ◽  
Rui Lin Hu ◽  
Xin Wei
Keyword(s):  
Principal Stress ◽  
Retaining Wall ◽  
Ground Surface ◽  
Earth Pressure ◽  
Intermediate Principal Stress ◽  
Strength Theory ◽  
Passive Earth Pressure ◽  
Unified Strength Theory ◽  
Retaining Structure ◽  
Lateral Earth Pressure

Estimating passive earth pressure accurately is very important when designing retaining wall. Based on the unified strength theory and plane strain assumption, an analytical solution has been developed to determine the passive lateral earth pressure distribution on a retaining structure when the backfill is cohesive and inclined considering the effect of the intermediate principal stress. The solution derived encompasses both Bell’s equation (for cohesive or cohesionless backfill with a horizontal ground surface) and Rankine’s solution (for cohesionless backfill with an inclined ground surface).

Coefficients of active earth pressure with seepage effect

2012 ◽  
Vol 49 (6) ◽  
pp. 651-658 ◽  
Author(s):  
Pérsio L.A. Barros ◽  
Petrucio J. Santos
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Retaining Wall ◽  
Drainage System ◽  
Numerical Procedure ◽  
Ground Surface ◽  
Earth Pressure ◽  
Friction Angle ◽  
Active Earth Pressure ◽  
Plane Failure

A calculation method for the active earth pressure on the possibly inclined face of a retaining wall provided with a drainage system along the soil–structure interface is presented. The soil is cohesionless and fully saturated to the ground surface. This situation may arise during heavy rainstorms. To solve the problem, the water seepage through the soil is first analyzed using a numerical procedure based on the boundary element method. Then, the obtained pore-water pressure is used in a Coulomb-type formulation, which supposes a plane failure surface inside the backfill when the wall movement is enough to put the soil mass in the active state. The formulation provides coefficients of active pressure with seepage effect which can be used to evaluate the active earth thrust on walls of any height. A series of charts with values of the coefficients of active earth pressure with seepage calculated for selected values of the soil internal friction angle, the wall–soil friction angle, and the wall face inclination is presented.

Study on Soil Pressure of High Fill Retaining Wall in Construction Stage

2012 ◽  
Vol 204-208 ◽  
pp. 718-721 ◽  
Author(s):  
Peng Li ◽  
Xiao Song
Keyword(s):  
Retaining Wall ◽  
Earth Pressure ◽  
Monitoring Data ◽  
Experiment Study ◽  
Pressure Monitoring ◽  
Soil Pressure ◽  
Construction Stage ◽  
The Earth ◽  
Pressure Calculation ◽  
Practical Guidance

The traditional formula using for the calculation of Expressway on high embankment of the retaining wall and the earth pressure can not be very good practical. In order to accurately determine the soil pressure calculation of the complex retaining wall in construction stage for guaranteeing the engineering safety, the experiment study on soil pressure is done, and the study on soil pressure monitoring data is also done. Then the valuable conclusions are obtained to facilitate better practical guidance for construction.

Active earth pressure in cohesive soils with an inclined ground surface

2000 ◽  
Vol 37 (1) ◽  
pp. 171-177 ◽  
Author(s):  
Nirmala Gnanapragasam
Keyword(s):  
Analytical Solution ◽  
Ground Surface ◽  
Earth Pressure ◽  
Failure Surface ◽  
Friction Angle ◽  
Active Earth Pressure ◽  
Overburden Pressure ◽  
Retaining Structure ◽  
Lateral Earth Pressure ◽  
Fixed Orientation

An analytical solution is developed to determine the active lateral earth pressure distribution on a retaining structure when it consists of a cohesive backfill (internal friction angle ϕ > 0, cohesion c > 0) with an inclined ground surface. The solution derived encompasses both Bell's equation (for cohesive or cohesionless backfill with a horizontal ground surface) and Rankine's solution (for cohesionless backfill with an inclined ground surface). The orientation of the failure surface is also determined. Results indicate that, unlike the soil-wall scenarios of Bell and Rankine where the failure planes are parallel with a fixed orientation independent of the overburden pressure, for sloping cohesive backfill (ϕ > 0, c > 0) the slope of the failure surface is a function of the overburden pressure and becomes shallower with depth, thus forming a curvilinear failure surface. The solution developed can also be used to check the sustainability of a slope. The analytical solution can be programmed conveniently in a computer.Key words: retaining structure, active earth pressure, cohesive backfill.

A Double Inequality Method for Calculate the Loading Capacity of a Sheet Pile DIMSP

2012 ◽  
Vol 268-270 ◽  
pp. 725-728
Author(s):  
Yi Huan Xie
Keyword(s):  
Retaining Wall ◽  
Engineering Application ◽  
Earth Pressure ◽  
Plasticity Condition ◽  
Loading Capacity ◽  
Sheet Pile ◽  
Double Inequality ◽  
The Earth ◽  
Additional Correction ◽  
Set Up

The passive earth pressure on the both sides of a sheet pile retaining wall is owing to plasticity bounded, a fact that affects the horizontal loading capacity of the wall. In order to find out a method, that the loading capacity of the wall can be analytically calculated and the mentioned constrain could be token into account, the paper set up a DIMSP model, which consists of mechanics equilibrium principle including two inequalities for the plasticity condition of earth pressure. The deduced solution of the model is capable of calculating the bearing capacity, and possesses the advantages of no additional correction of the cut in depth of the wall. Further more the continuity of earth pressure distribution is ensured by this model, an adjustment of the earth pressure figure is also without difficulty possible. For engineering application some graphics are given, the cut in depth of the wall can be read from them conveniently.

Sign in / Sign up

Export Citation Format

Share Document