Current control design for three-phase grid-connected inverters using a pole placement technique based on numerical models

2012 ◽  
Author(s):  
C. Citro ◽  
C. Gavriluta ◽  
Md H. K. Nizak ◽  
Hector Beltran
Keyword(s):  
Numerical Models ◽  
Control Design ◽  
Current Control ◽  
Pole Placement ◽  
Three Phase ◽  
Placement Technique

scholarly journals Improved Self-Sensing Speed Control of IPMSM Drive Based on Cascaded Nonlinear Control

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2205
Author(s):  
Muhammad Usama ◽  
Jaehong Kim
Keyword(s):  
Fuzzy Logic Controller ◽  
Control Design ◽  
Speed Control ◽  
Current Control ◽  
The Self ◽  
Pole Placement ◽  
Motor Drive ◽  
Control Performance ◽  
Control Loop ◽  
Maximum Torque

This paper presents a nonlinear cascaded control design that has been developed to (1) improve the self-sensing speed control performance of an interior permanent magnet synchronous motor (IPMSM) drive by reducing its speed and torque ripples and its phase current harmonic distortion and (2) attain the maximum torque while utilizing the minimum drive current. The nonlinear cascaded control system consists of two nonlinear controls for the speed and current control loop. A fuzzy logic controller (FLC) is employed for the outer speed control loop to regulate the rotor shaft speed. Model predictive current control (MPCC) is utilized for the inner current control loop to regulate the drive phase currents. The nonlinear equation for the dq reference current is derived to implement the maximum torque per armature (MTPA) control to achieve the maximum torque while using the minimum current values. The model reference adaptive system (MRAS) was employed for the speed self-sensing mechanism. The self-sensing speed control performance of the IPMSM motor drive was compared with that of the traditional cascaded control schemes. The stability of the sensorless mechanism was studied using the pole placement method. The proposed nonlinear cascaded control was verified based on the simulation results. The robustness of the control design was ensured under various loads and in a wide speed range. The dynamic performance of the motor drive is improved while circumventing the need to tune the proportional-integral (PI) controller. The self-sensing speed control performance of the IPMSM drive was enhanced significantly by the designed cascaded control model.

PID Control Design for a Maglev Train System

2013 ◽  
Vol 389 ◽  
pp. 425-429 ◽  
Author(s):  
Fernandes Braga Junior Gilson ◽  
Augusto Lima Barreiros José
Keyword(s):  
Taylor Series ◽  
Pid Control ◽  
Magnetic Levitation ◽  
Control Design ◽  
Operating Conditions ◽  
Pole Placement ◽  
Maglev Train ◽  
Proportional Integral ◽  
Train System ◽  
Placement Technique

This document presents an application of a PID (proportional, integral and derivative) controller designed by the pole placement technique and applied to a Maglev (Magnetic Levitation) train system plant. The linearization with Taylor Series is demonstrated including the development of the formulas to calculate the parameters of the controllers to three operation points and the performance of each controller is tested under disturbances, and switching controllers between the plants for different operating conditions.

Inductor Saturation Compensation in Three-Phase Three-Wire Voltage-Source Converters via Inverse System Dynamics-I

2020 ◽  
Author(s):  
Ziya Özkan ◽  
Ahmet Masum Hava
Keyword(s):  
Dynamic Model ◽  
Dynamic Performance ◽  
Current Control ◽  
Inverse System ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Two Phase ◽  
Inverse Dynamic ◽  
Three Phase ◽  
Steady State Current

In three-phase three-wire (3P3W) voltage-source converter (VSC) systems, utilization of filter inductors with deep saturation characteristics is often advantageous due to the improved size, cost, and efficiency. However, with the use of conventional synchronous frame current control (CSCC) methods, the inductor saturation results in significant dynamic performance loss and poor steady-state current waveform quality. This paper proposes an inverse dynamic model based compensation (IDMBC) method to overcome these performance issues. Accordingly, a review of inductor saturation and core materials is performed, and the motivation on the use of saturable inductors is clarified. Then, two-phase exact modelling of the 3P3W VSC control system is obtained and the drawbacks of CSCC have been demonstrated analytically. Based on the exact modelling, the inverse system dynamic model of the nonlinear system is obtained and employed such that the nonlinear plant is converted to a fictitious linear inductor system for linear current regulators to perform satisfactorily.

Virtual Damping Control Design of Three-Phase Grid-Tied PV Inverters for Passivity Enhancement

2020 ◽  
pp. 1-1
Author(s):  
Zhiqing Yang ◽  
Chirag Shah ◽  
Tianxiao Chen ◽  
Jakob Teichrib ◽  
Rik W. De Doncker
Keyword(s):  
Control Design ◽  
Damping Control ◽  
Three Phase
Sign in / Sign up

Export Citation Format

Share Document