Design of HIAF Module Power Supply Control Board

2021 ◽  
Author(s):  
Yuhang Li ◽  
Xiaojun Wang ◽  
Fengjun Wu ◽  
Jiqiang Li ◽  
Shuai Zhang ◽  
...  
Keyword(s):  
Power Supply ◽  
Control Board

Elevator Brake Release Automatic Control System

2011 ◽  
Vol 130-134 ◽  
pp. 3502-3504
Author(s):  
De Min Zhang ◽  
Xue Hui Liang
Keyword(s):  
Control System ◽  
Automatic Control ◽  
Automatic Control System ◽  
Power Supply ◽  
Operation Mode ◽  
Control Board ◽  
Rescue Operation ◽  
Floor Level ◽  
Electrical Control ◽  
Operation Control

The brake release electrical control board is a very important element of the elevator rescue operation control system. The brake release board provides a power supply to operate an elevator brake by a battery in rescue operation mode to allow a motion of a car until the next floor level to release any passengers. The brake release board has some buttons to operate the car and some LED’s to indicate the state of running. There are also some parameters in the board to adjust the operation.

New replica method with plasma polymerized film by glow discharge

1988 ◽  
Vol 46 ◽  
pp. 414-415
Author(s):  
A. Tanaka ◽  
M. Yamaguchi ◽  
T. Hirano
Keyword(s):  
Power Supply ◽  
Plasma Polymerization ◽  
Vacuum Chamber ◽  
Complex Surface ◽  
Replica Method ◽  
Metal Extraction ◽  
High Voltage Power Supply ◽  
Negative Glow ◽  
Hydrocarbon Gas ◽  
Hydrocarbon Molecules

The plasma polymerization replica method and its apparatus have been devised by Tanaka (1-3). We have published several reports on its application: surface replicas of biological and inorganic specimens, replicas of freeze-fractured tissues and metal-extraction replicas with immunocytochemical markers.The apparatus for plasma polymerization consists of a high voltage power supply, a vacuum chamber containing a hydrocarbon gas (naphthalene, methane, ethylene), and electrodes of an anode disk and a cathode of the specimen base. The surface replication by plasma polymerization in negative glow phase on the cathode was carried out by gassing at 0.05-0.1 Torr and glow discharging at 1.5-3 kV D.C. Ionized hydrocarbon molecules diffused into complex surface configurations and deposited as a three-dimensionally polymerized film of 1050 nm in thickness.The resulting film on the complex surface had uniform thickness and showed no granular texture. Since the film was chemically inert, resistant to heat and mecanically strong, it could be treated with almost any organic or inorganic solvents.

Development of the algorithm for the selection of a wind generator-based autonomous power supply system

2019 ◽  
Vol 2 (1) ◽  
pp. 8-16 ◽  
Author(s):  
P. A. Khlyupin ◽  
G. N. Ispulaeva
Keyword(s):  
Wind Turbines ◽  
Power Supply ◽  
Alternative Energy ◽  
Power Supply System ◽  
Supply System ◽  
Power Generators ◽  
Energy Devices ◽  
Wind Generator ◽  
Alternative Energy Sources ◽  
Selection Of

Introduction: The co-authors provide an overview of the main types of wind turbines and power generators installed into wind energy devices, as well as advanced technological solutions. The co-authors have identified the principal strengths and weaknesses of existing wind power generators, if applied as alternative energy sources. The co-authors have proven the need to develop an algorithm for the selection of a wind generator-based autonomous power supply system in the course of designing windmill farms in Russia. Methods: The co-authors have analyzed several types of wind turbines and power generators. Results and discussions: The algorithm for the selection of a wind generator-based autonomous power supply system is presented as a first approximation. Conclusion: The emerging algorithm enables designers to develop an effective wind generator-based autonomous power supply system.

SISTEM AUTOMATIC SWITCH REDUNDANT UPS UNTUK BEBAN ESSENSIAL

2019 ◽  
Vol 5 (1) ◽  
pp. 35-45
Author(s):  
Markus Dwiyanto Tobi ◽  
Alimuddin Mappa
Keyword(s):  
Power Supply ◽  
Working Condition ◽  
Control Circuit ◽  
Energy Sources ◽  
Main Equipment ◽  
Telecommunication Equipment ◽  
Input Condition ◽  
Research Designs ◽  
Switch Circuit

The role of the power supply device is to produce, process and distribute energy sources. Telecommunication equipment can only operate if it has continuous supply. Therefore, to maintain the continuity of the supply, a UPS (Uninterruptable Power Supply) device system is needed so that the supply to the Essential Load device will remain available so that continuity will be maintained. This research designs and proposes how a series of automatic redundant switch systems on UPS to ensure the availability of power supply for the main equipment of telecommunications systems. The Auto switch circuit is designed to have 3 (three) working stages which will trigger the relay driver as control circuit, namely the normal working condition of the contactor input K1 is present, the input condition is zero (lost), and the input condition is present. This system can automatically supply power to telecommunications equipment.

Case Study of the Design for Reliability for Remanufactured Military Power Supply

2020 ◽  
Vol 20 (3) ◽  
pp. 209-215
Author(s):  
Hyun-Seok Song ◽  
Min-Ho Son ◽  
Sung-Ju Yoo ◽  
Do-Hyun Jung ◽  
Boo-Hee Park
Keyword(s):  
Power Supply ◽  
Military Power ◽  
Design For Reliability
Sign in / Sign up

Export Citation Format

Share Document