Three-phase PFC rectifier with high efficiency and low cost for small PM synchronous wind generators

2016 ◽  
Author(s):  
Ghasem Rezazadeh ◽  
Farzad Tahami ◽  
Hamed Valipour
Keyword(s):  
High Efficiency ◽  
Low Cost ◽  
Wind Generators ◽  
Three Phase

scholarly journals Study and Implementation of a Cost-Effective 3L-Active Rectifier for DC Collection in WECS

2019 ◽  
Vol 118 ◽  
pp. 02065
Author(s):  
Muhammad Luqman ◽  
Gang Yao ◽  
Lidan Zhou ◽  
Di Yang ◽  
Anil Lamichhane
Keyword(s):  
Low Cost ◽  
Cost Effective ◽  
Cost Comparison ◽  
Multilevel Converters ◽  
Wind Generators ◽  
Active Rectifier ◽  
Vienna Rectifier ◽  
Three Phase ◽  
Control Scheme ◽  
Parallel Configuration

Power electronic converters are widely used in wind energy conversion system (WECS) applications. Therefore, with the increasing manufacturing capacity of multi-MW wind generators, multi-level converters, or parallel configuration of converters are becoming more attractive solutions towards DC collection from the wind generator. Among the multilevel converters, three-level full-scale neutral point diode clamped (3L-NPC) converter are using extensively for such applications in order to reduce the voltage stress on the semiconductor devices. In this article, a comparative study based on several devices used by NPC, capacitor clamped (CC) as well as Vienna rectifier has been done. Furthermore, their estimated cost comparison and complexity of control switches have been debated. By keeping in view the merits and demerits of these rectifiers, a low cost three-level active rectifier having a smaller number of active switches with a simple control scheme have been implemented. Considering a three-phase electric grid as a generated source, a 2.2KW low-cost three-level Vienna rectifier is simulated using MATLAB/Simulink. DSP (TMS320F28335) based experimental results ratify the simulated circuit with THD<5%.

scholarly journals H7 three phase transformerless inverter for photovoltaic grid-tied system with maximum power point operation

2021 ◽  
Vol 12 (3) ◽  
pp. 1853
Author(s):  
Essam Hendawi ◽  
Sherif Zaid
Keyword(s):  
Power Systems ◽  
Leakage Current ◽  
High Efficiency ◽  
Low Cost ◽  
Harmonic Distortion ◽  
Boost Converter ◽  
Phase Inverter ◽  
The Earth ◽  
Three Phase ◽  
Three Phase Inverter

<span lang="EN-US">One of the most important and common parts of the modern power systems is the grid-connected photovoltaic (PV) systems. Recently, these systems have gotten a big revolution due to the introduction of the transformerless inverters. It has the merits of small size, low cost, and high efficiency. However, transformerless inverters has a general safety problem related to the earth leakage current. Various researches were directed toward evolving their performance and diminishing the leakage current to the standard limits. This article proposes an application of the H7 controller to a PV powered grid-tied three phase transformerless inverter. The transformerless inverter is linked with the grid through a boost converter. The boost converter inductance is rearranged and divided to reduce the earth leakage current of the system. simulations are carried out for the proposed H7 PV grid-tied system and for a system that uses the conventional three phase inverter. The simulation results show that the H7 inverter provides lower leakage current, higher efficiency, and lower total harmonic distortion (THD) compared to the conventional three phase inverter.</span>

Simple and Flexible Power Loss Minimizer with Low-Cost MCU Implementation for High-Efficiency Three-Phase Induction Motor Drives

2021 ◽  
pp. 1-1
Author(s):  
Adriana Bruno ◽  
Massimo Caruso ◽  
Antonino Oscar Di Tommaso ◽  
Rosario Miceli ◽  
Claudio Nevoloso ◽  
...  
Keyword(s):  
Induction Motor ◽  
Power Loss ◽  
High Efficiency ◽  
Low Cost ◽  
Motor Drives ◽  
Induction Motor Drives ◽  
Three Phase

Influence of MBE Growth Conditions on Dislocation Densities of GaAs/Ge Epilayers Grown on Silicon Substrates

1985 ◽  
Vol 43 ◽  
pp. 364-365
Author(s):  
K.M. Hones ◽  
P. Sheldon ◽  
B.G. Yacobi ◽  
A. Mason
Keyword(s):  
High Efficiency ◽  
Lattice Mismatch ◽  
Low Cost ◽  
Growth Conditions ◽  
Nonradiative Recombination ◽  
Device Structure ◽  
Si Substrates ◽  
Transmission Electron ◽  
Dislocation Densities ◽  
Dislocation Type

There is increasing interest in growing epitaxial GaAs on Si substrates. Such a device structure would allow low-cost substrates to be used for high-efficiency cascade- junction solar cells. However, high-defect densities may result from the large lattice mismatch (∼4%) between the GaAs epilayer and the silicon substrate. These defects can act as nonradiative recombination centers that can degrade the optical and electrical properties of the epitaxially grown GaAs. For this reason, it is important to optimize epilayer growth conditions in order to minimize resulting dislocation densities. The purpose of this paper is to provide an indication of the quality of the epitaxially grown GaAs layers by using transmission electron microscopy (TEM) to examine dislocation type and density as a function of various growth conditions. In this study an intermediate Ge layer was used to avoid nucleation difficulties observed for GaAs growth directly on Si substrates. GaAs/Ge epilayers were grown by molecular beam epitaxy (MBE) on Si substrates in a manner similar to that described previously.

Advance Protection for Three Phase Induction Motor using Microcontroller Atmega32

2018 ◽  
Vol 8 (1) ◽  
pp. 172
Author(s):  
Karan S Belsare ◽  
Gajanan D Patil
Keyword(s):  
Induction Motor ◽  
Low Cost ◽  
Short Circuit ◽  
Cost Factor ◽  
Protection Scheme ◽  
Three Phase ◽  
The Cost

A low cost and reliable protection scheme has been designed for a three phase induction motor against unbalance voltages, under voltage, over voltage, short circuit and overheating protection. Taking the cost factor into consideration the design has been proposed using microcontroller Atmega32, MOSFETs, relays, small CTs and PTs. However the sensitivity of the protection scheme has been not compromised. The design has been tested online in the laboratory for small motors and the same can be implemented for larger motors by replacing the i-v converters and relays of suitable ratings.

Improvement of Ti/RuO2–IrO2 Anode Lifetime and Electrocatalytical Properties by Using an Eco-Friendly Thermal Decomposition Method Using Polyvinyl Alcohol as Solvent

2019 ◽  
Author(s):  
Charlys Bezerra ◽  
Géssica Santos ◽  
Marilia Pupo ◽  
Maria Gomes ◽  
Ronaldo Silva ◽  
...  
Keyword(s):  
Thermal Decomposition ◽  
Polyvinyl Alcohol ◽  
High Efficiency ◽  
Electrochemical Impedance ◽  
Pechini Method ◽  
Low Cost ◽  
Charge Transfer Resistance ◽  
Transfer Resistance ◽  
Calcination Temperatures ◽  
Service Lifetime

<p>Electrochemical oxidation processes are promising solutions for wastewater treatment due to their high efficiency, easy control and versatility. Mixed metal oxides (MMO) anodes are particularly attractive due to their low cost and specific catalytic properties. Here, we propose an innovative thermal decomposition methodology using <a>polyvinyl alcohol (PVA)</a> as a solvent to prepare Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes. Comparative anodes were prepared by conventional method employing a polymeric precursor solvent (Pechini method). The calcination temperatures studied were 300, 400 and 500 °C. The physical characterisation of all materials was performed by X-ray diffraction and scanning electron microscopy coupled with energy dispersive spectroscopy, while electrochemical characterisation was done by cyclic voltammetry, accelerated service lifetime and electrochemical impedance spectroscopy. Both RuO<sub>2</sub> and IrO<sub>2</sub> have rutile-type structures for all anodes. Rougher and more compact surfaces are formed for the anodes prepared using PVA. Amongst temperatures studied, 300 °C using PVA as solvent is the most suitable one to produce anodes with expressive increase in voltammetric charge (250%) and accelerated service lifetime (4.3 times longer) besides reducing charge-transfer resistance (8 times lower). Moreover, the electrocatalytic activity of the anodes synthesised with PVA toward the Reactive Blue 21 dye removal in chloride medium (100 % in 30 min) is higher than that prepared by Pechini method (60 min). Additionally, the removal total organic carbon point out improved mineralisation potential of PVA anodes. Finally, this study reports a novel methodology using PVA as solvent to synthesise Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes with improved properties that can be further extended to synthesise other MMO compositions.</p>

Identificación de polaridad de los devanados en un motor trifásico de 6 terminales

2019 ◽  
pp. 13-19
Author(s):  
José Luis Viramontes-Reyna ◽  
Josafat Moreno-Silva ◽  
José Guadalupe Montelongo-Sierra ◽  
Erasmo Velazquez-Leyva
Keyword(s):  
Low Cost ◽  
Voltage Reference ◽  
Three Phase ◽  
Voltage Phase ◽  
The Law ◽  
And Control

This document presents the results obtained from the application of the law of Lens to correctly identify the polarity of the windings in a three-phase motor with 6 exposed terminals, when the corresponding labeling is not in any situation; Prior to identifying the polarity, it should be considered to have the pairs of the three windings located. For the polarity, it is proposed to feed with a voltage of 12 Vrms to one of the windings, which are identified randomly as W1 and W2, where W1 is connected to the voltage phase of 12 Vrms of the signal and W2 to the voltage reference to 0V; by means of voltage induction and considering the law of Lens, the remaining 4 terminals can be identified and labeled as V1, V2, U1 and U2. For this process a microcontroller and control elements with low cost are used.

Contradiction Analysis and Solution in the R&D of High-Power Solar LED Street Lamp Controller

2019 ◽  
Vol 12 (1) ◽  
pp. 12-19
Author(s):  
Zhengwang Xu ◽  
Wei Mei ◽  
Jiaqi Yu ◽  
Jiarui Zhang ◽  
Yuchun Yi ◽  
...  
Keyword(s):  
Power Supply ◽  
High Efficiency ◽  
Low Cost ◽  
Solar Panel ◽  
Battery Voltage ◽  
Supply Circuit ◽  
Led Light ◽  
Power Supply Circuit ◽  
Side Mode ◽  
Dual Power

As being restricted by factors such as cost, efficiency and size, the development of high-power solar LED street light controller is faced with plenty of difficulties. In case that a structure of two independent DC/DC is applied as the main circuit, it has to face problems such as large size and high cost; in case of applying the bidirectional BUCK/BOOST circuit, it requires change-over switches to control the solar panel and LED light. As being restricted by withstanding voltage, on-resistance and cost, a PMOS device cannot be used as the change-over switch of solar panel and LED light. However, when being used as a change-over switch, an NMOS device must apply the low-side mode under which the negative ends of the mentioned three parts are cut off. In the condition of applying the low-side mode, a differential circuit must be used to detect the voltage of the solar panel. Furthermore, in order to make sure batteries can still be regularly charged after wearing out in daylight, the controller must be supplied with power through a dual power supply circuit that can obtain power from both the solar panel and the battery. The demander has a requirement on extremely low standby power consumption of the product, and thus it is necessary to minimize the circuit that is live while working in standby mode. Methods: The bidirectional BUCK/BOOST circuit structure is applied to the main circuit to realize a higher change-over efficiency while giving considerations to both cost and size. The NMOS device, model IRFB4410ZPBF, with a price of about three yuan, is used as the switching device, and the low-side mode is applied, that is the switches inserted in between negative end of the solar panel or LED light and that of the DC/DC circuit. The low-cost rail-to-rail operational amplifier LM358 is used to form a differential amplification circuit for detecting the voltage of the solar panel. A XL1509-12E1 chip that only costs 0.88 yuan/pc is selected as the main change-over chip for the power supply, which has realized the highly-efficient and low-cost change-over of the power supply. A dual power supply circuit and a step-down protective circuit are designed for the XL1509-12E1 change-over chip. By comparing solar panel voltage with battery voltage, the solar panel booting circuit is realized. Only when solar panel voltage is higher than battery voltage, does the system program start to power it up for running, so that the outage of most of the circuits of the system under standby mode does not consume energy. Furthermore, the solar panel voltage detecting circuit, the solar panel booting circuit and several return difference functions are corrected during system debugging. Results: The circuit board of the entire controller features small size, low cost and high efficiency. It measures about 100*62*18mm in size, costs about 60 yuan, and the charge/discharge change-over efficiency reaches up to over 95%. The controller has many functions: it is capable of operating within a large scope, in which, solar panel voltage is subject to 15~50V, LED light voltage is subject to 15~60V, battery voltage is subject to 10~35V and battery-end charge/discharge current is 10A; it is capable of adapting to monocrystalline silicon/multicrystalline silicon/thin-film and many other kinds of solar panels, as well as lithium/lead-acid and many other kinds of batteries; it is capable of detecting the conversion of day and night, automatically controlling charging and discharging and automatically making adaptive adjustment according to seasonal variations; the current to be consumed during standby will be maintained below 3mA, and thus the power consumption is extremely low. Conclusion: By selecting the bidirectional BUCK/BOOST circuit structure, applying low-side mode for switching of solar panel and LED light, using a differential circuit to detect solar panel voltage, using a low-cost DC/DC chip to realize power supply change-over, designing a dual power supply circuit, introducing solar panel booting circuit and other hardware design, as well as MPPT algorithm, state recognition and control, return difference control and other software design, a solar LED street light control product featuring small size, low cost, high efficiency and multiple functions is successfully developed.

Sign in / Sign up

Export Citation Format

Share Document