Assessing the effects of sub‐tropical winter thermal conditions on coolwater fish reproduction

2021 ◽  
Author(s):  
John D. Cannaday ◽  
Troy M. Farmer
2018 ◽  
pp. 155-162 ◽  
Author(s):  
Sergei S. Kapitonov ◽  
Anastasia V. Kapitonova ◽  
Sergei Yu. Grigorovich ◽  
Sergei A. Medvedev ◽  
Taher Sobhy

In the article, the electrical and thermal processes in the LED lamp with varied parameters are investigated. Voltage and current measurements on all LEDs of the luminaire are carried out in the nominal operating mode. The power allocated to each LED is determined. The calculation of the LED crystal temperature was carried out using the developed thermal LED model based on the results of the measurements and by using “Multisim” program. It has been established that the temperature of the crystals of individual LEDs in the luminaire differ significantly, which leads to unfavourable thermal conditions for them and an increased likelihood of premature failure.


2017 ◽  
Vol 191 ◽  
pp. 176-195 ◽  
Author(s):  
Igor D. Rostov ◽  
Elena V. Dmitrieva ◽  
Alexander A. Vorontsov

2020 ◽  
Vol 38 (9A) ◽  
pp. 1257-1275
Author(s):  
Wisam M. Mareed ◽  
Hasanen M. Hussen

 Elevated CO2 rates in a building affect the health of the occupant. This paper deals with an experimental and numerical analysis conducted in a full-scale test room located in the Department of Mechanical Engineering at the University of Technology. The experiments and CFD were conducted for analyzing ventilation performance. It is a study on the effect of the discharge airflow rate of the ceiling type air-conditioner on ventilation performance in the lecture room with the mixing ventilation. Most obtained findings show that database and questionnaires analyzed prefer heights between 0.2 m to 1.2 m in the middle of an occupied zone and breathing zone height of between 0.75 m to 1.8 given in the literature surveyed. It is noticed the mismatch of internal conditions with thermal comfort, and indoor air quality recommended by [ASHRAE Standard 62, ANSI / ASHRAE Standard 55-2010]. CFD simulations have been carried to provide insights on the indoor air quality and comfort conditions throughout the classroom. Particle concentrations, thermal conditions, and modified ventilation system solutions are reported.


2020 ◽  
pp. 75-86
Author(s):  
Sergio Antonio Camargo ◽  
Lauro Correa Romeiro ◽  
Carlos Alberto Mendes Moraes

The present article aimed to test changes in cooling water temperatures of males, present in aluminum injection molds, to reduce failures due to thermal fatigue. In order to carry out this work, cooling systems were studied, including their geometries, thermal gradients and the expected theoretical durability in relation to fatigue failure. The cooling system tests were developed with the aid of simulations in the ANSYS software and with fatigue calculations, using the method of Goodman. The study of the cooling system included its geometries, flow and temperature of this fluid. The results pointed to a significant increase in fatigue life of the mold component for the thermal conditions that were proposed, with a significant increase in the number of cycles, to happen failures due to thermal fatigue.


Author(s):  
S. Assylbekova ◽  
N. Badryzlova ◽  
L. Kushnikova

The article presents the results of the first research on artificial reproduction in industrial conditions of the endemic, narrow-areal subspecies of Brachymystax lenok Savinovi, which lives in lake Markakol, East Kazakhstan region. The indicators of the heat sum characteristic for each stage of development, the rate of development and growth of the Markakolsky lenok from the moment of pre-breeding to late juveniles are described. To develop technological approaches for artificial fish reproduction, one of the most important points is to determine the optimal conditions for each stage and assess the risks (loss of fish products). At the stage of insemination and transportation of eggs to the place of incubation, the loss was 50 %. The largest losses of fish products were registered during the incubation stage. The most painlessly passed the period of holding and lifting on the float, where the loss was only 3 %. When growing pre-larvae and larvae in the pool, the daily waste did not exceed 1 %. Small-sized animals that were unable to adapt to artificial feeds fell into the waste. Losses during this period amounted to 15 % of the previous stage. In General, the yield of juveniles from the moment of fertilization to the end of the experiment was 16 %. The crucial factor in the development and growth of Lenok Markakolosky is the temperature regime. For the period of embryonic development, the most favorable water temperature is 7–8 °C. From the moment of hatching, the water temperature must be increased to 10–12 °C, and the optimal temperature for the cage growing of fingerlings varies from 12 to 14 °C.


Sign in / Sign up

Export Citation Format

Share Document