Variable Property and Temperature Ratio Effects on Nusselt Numbers in a Rectangular Channel With 45 Deg Angled Rib Turbulators

2003 ◽  
Vol 125 (5) ◽  
pp. 769-778 ◽  
Author(s):  
G. I. Mahmood ◽  
P. M. Ligrani ◽  
K. Chen
Keyword(s):  
Flow Direction ◽  
Rectangular Channel ◽  
Channel Height ◽  
Global Changes ◽  
Stagnation Temperature ◽  
Temperature Ratio ◽  
Height Range ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Rib Turbulators

Measured local and spatially-averaged Nusselt numbers and friction factors (all time-averaged) are presented which show the effects of temperature ratio and variable properties in a rectangular channel with rib turbulators, and an aspect ratio of 4. The ratio of air inlet stagnation temperature to local surface temperature Toi/Tw varies from 0.66 to 0.95, and Reynolds numbers based on channel height range from 10,000 to 83,700. The square cross-section ribs are placed on two opposite surfaces, and are oriented at angles of +45 deg and −45 deg, respectively, with respect to the bulk flow direction. The ratio of rib height to channel hydraulic diameter is 0.078, the rib pitch-to-height ratio is 10, and the ribs block 25 percent of the channel cross-sectional area. Ratios of globally-averaged rib Nusselt numbers to baseline, constant property Nusselt numbers, Nu̿/Nuo,cp, increase from 2.69 to 3.10 as the temperature ratio Toi/Tw decreases from 0.95 to 0.66 (provided Reynolds number ReH is approximately constant). Friction factor ratios f/fo,cp then decrease as Toi/Tw decreases over this same range of values. In each case, a correlation equation is given which matches the measured global variations. Such global changes are a result of local Nusselt number ratio increases with temperature ratio, which are especially pronounced on the flat surfaces just upstream and just downstream of individual ribs. Thermal performance parameters are also given, which are somewhat lower in the ribbed channel than in channels with dimples and/or protrusions mostly because of higher rib form drag and friction factors.

Spatially Resolved Heat Transfer and Friction Factors in a Rectangular Channel With 45-Deg Angled Crossed-Rib Turbulators

2003 ◽  
Vol 125 (3) ◽  
pp. 575-584 ◽  
Author(s):  
P. M. Ligrani ◽  
G. I. Mahmood
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Rectangular Channel ◽  
Test Surface ◽  
Spatially Resolved ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Smooth Channel ◽  
Rib Turbulators

Spatially resolved Nusselt numbers, spatially averaged Nusselt numbers, and friction factors are presented for a stationary channel with an aspect ratio of 4 and angled rib turbulators inclined at 45 deg with perpendicular orientations on two opposite surfaces. Results are given at different Reynolds numbers based on channel height from 10,000 to 83,700. The ratio of rib height to hydraulic diameter is .078, the rib pitch-to-height ratio is 10, and the blockage provided by the ribs is 25% of the channel cross-sectional area. Nusselt numbers are given both with and without three-dimensional conduction considered within the acrylic test surface. In both cases, spatially resolved local Nusselt numbers are highest on tops of the rib turbulators, with lower magnitudes on flat surfaces between the ribs, where regions of flow separation and shear layer reattachment have pronounced influences on local surface heat transfer behavior. The augmented local and spatially averaged Nusselt number ratios (rib turbulator Nusselt numbers normalized by values measured in a smooth channel) vary locally on the rib tops as Reynolds number increases. Nusselt number ratios decrease on the flat regions away from the ribs, especially at locations just downstream of the ribs, as Reynolds number increases. When adjusted to account for conduction along and within the test surface, Nusselt number ratios show different quantitative variations (with location along the test surface), compared to variations when no conduction is included. Changes include: (i) decreased local Nusselt number ratios along the central part of each rib top surface as heat transfer from the sides of each rib becomes larger, and (ii) Nusselt number ratio decreases near corners, where each rib joins the flat part of the test surface, especially on the downstream side of each rib. With no conduction along and within the test surface (and variable heat flux assumed into the air stream), globally-averaged Nusselt number ratios vary from 2.92 to 1.64 as Reynolds number increases from 10,000 to 83,700. Corresponding thermal performance parameters also decrease as Reynolds number increases over this range, with values in approximate agreement with data measured by other investigators in a square channel also with 45 deg oriented ribs.

Effects of Dimple Depth on Nusselt Numbers and Friction Factors for Internal Cooling in a Channel

2004 ◽  
Author(s):  
N. K. Burgess ◽  
P. M. Ligrani
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Local Nusselt Number ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Channel Height ◽  
Stagnation Temperature ◽  
Nusselt Numbers ◽  
Number Ratio ◽  
Friction Factors

Experimental results, measured on dimpled test surfaces placed on one wall of different channels, are given for a ratio of air inlet stagnation temperature to surface temperature of approximately 0.94, and Reynolds numbers based on channel height from 9,940 to 74,800. The data presented include friction factors, local Nusselt numbers, spatially-averaged Nusselt numbers, and globally-averaged Nusselt numbers. The ratios of dimple depth to dimple print diameter δ/D are 0.1, 0.2, and 0.3 to provide information on the influences of dimple depth. The ratio of channel height to dimple print diameter is 1.00. At all Reynolds numbers considered, local and spatially-resolved Nusselt number augmentations increase as dimple depth increases (and all other experimental and geometric parameters are held approximately constant). These are attributed to: (i) increases in the strengths and intensity of vortices and associated secondary flows ejected from the dimples, as well as (ii) increases in the magnitudes of three-dimensional turbulence production and turbulence transport. The effects of these phenomena are especially apparent in local Nusselt number ratio distributions measured just inside of the dimples, and just downstream of the downstream edges of the dimples. Data are also presented to illustrate the effects of Reynolds number, and streamwise development for δ/D = 0.1 dimples. Significant local Nusselt number ratio variations are observed at different streamwise locations, whereas variations with Reynolds number are mostly apparent on flat surfaces just downstream of individual dimples.

Effects Of Dimple Depth on Channel Nusselt Numbers and Friction Factors

2004 ◽  
Vol 127 (8) ◽  
pp. 839-847 ◽  
Author(s):  
N. K. Burgess ◽  
P. M. Ligrani
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Local Nusselt Number ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Channel Height ◽  
Stagnation Temperature ◽  
Nusselt Numbers ◽  
Number Ratio ◽  
Friction Factors

Experimental results, measured on dimpled test surfaces placed on one wall of different rectangular channels, are given for a ratio of air inlet stagnation temperature to surface temperature of approximately 0.94, and Reynolds numbers based on channel height from 9940 to 74,800. The data presented include friction factors, local Nusselt numbers, spatially averaged Nusselt numbers, and globally averaged Nusselt numbers. The ratios of dimple depth to dimple print diameter δ∕D are 0.1, 0.2, and 0.3 to provide information on the influences of dimple depth. The ratio of channel height to dimple print diameter is 1.00. At all Reynolds numbers considered, local spatially resolved and spatially averaged Nusselt number augmentations increase as dimple depth increases (and all other experimental and geometric parameters are held approximately constant). These are attributed to (i) increases in the strengths and intensity of vortices and associated secondary flows ejected from the dimples, as well as (ii) increases in the magnitudes of three-dimensional turbulence production and turbulence transport. The effects of these phenomena are especially apparent in local Nusselt number ratio distributions measured just inside of the dimples and just downstream of the downstream edges of the dimples. Data are also presented to illustrate the effects of Reynolds number and streamwise development for δ∕D=0.1 dimples. Significant local Nusselt number ratio variations are observed at different streamwise locations, whereas variations with the Reynolds number are mostly apparent on flat surfaces just downstream of individual dimples.

Local Heat Transfer and Flow Structure on and Above a Dimpled Surface in a Channel

2000 ◽  
Author(s):  
G. I. Mahmood ◽  
M. L. Hill ◽  
D. L. Nelson ◽  
P. M. Ligrani ◽  
H.-K. Moon ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Local Heat Transfer ◽  
Streamwise Velocity ◽  
Test Surface ◽  
Channel Height ◽  
Stagnation Temperature ◽  
Vortex Pairs ◽  
Nusselt Numbers ◽  
Flow Visualizations

Experimental results, measured on and above a dimpled test surface placed on one wall of a channel, are given for Reynolds numbers from 1,250 to 61,500 and ratios of air inlet stagnation temperature to surface temperature ranging from 0.68 to 0.94. These include flow visualizations, surveys of time-averaged total pressure and streamwise velocity, and spatially-resolved local Nusselt numbers, which are measured using infrared thermography, used in conjunction with energy balances, thermocouples, and in situ calibration procedures. The ratio of channel height to dimple print diameter is 0.5. Flow visualizations show vortical fluid and vortex pairs shed from the dimples, including a large upwash region and packets of fluid emanating from the central regions of each dimple, as well as vortex pairs and vortical fluid which form near dimple diagonals. These vortex structures augment local Nusselt numbers near the downstream rims of each dimple, both slightly within each depression, and especially on the flat surface just downstream of each dimple. Such augmentations are spread over larger surface areas and become more pronounced as the ratio of inlet stagnation temperature to local surface temperature decreases. As a result, local and spatially-averaged heat transfer augmentations become larger as this temperature ratio decreases. This is due to the actions of vortical fluid in advecting cool fluid from the central parts of the channel to regions close to the hotter dimpled surface.

Nusselt Numbers and Flow Structure on and Above a Shallow Dimpled Surface Within a Channel Including Effects of Inlet Turbulence Intensity Level

2004 ◽  
Vol 127 (2) ◽  
pp. 321-330 ◽  
Author(s):  
P. M. Ligrani ◽  
N. K. Burgess ◽  
S. Y. Won
Keyword(s):  
Nusselt Number ◽  
Flow Structure ◽  
Turbulence Intensity ◽  
Local Nusselt Number ◽  
Channel Height ◽  
Intensity Level ◽  
Stagnation Temperature ◽  
Channel Inlet ◽  
Local Flow ◽  
Nusselt Numbers

Experimental results from a channel with shallow dimples placed on one wall are given for Reynolds numbers based on channel height from 3,700 to 20,000, levels of longitudinal turbulence intensity from 3% to 11% (at the entrance of the channel test section), and a ratio of air inlet stagnation temperature to surface temperature of approximately 0.94. The ratio of dimple depth to dimple print diameter δ∕D is 0.1, and the ratio of channel height to dimple print diameter H∕D is 1.00. The data presented include friction factors, local Nusselt numbers, spatially averaged Nusselt numbers, a number of time-averaged flow structural characteristics, flow visualization results, and spectra of longitudinal velocity fluctuations which, at a Reynolds number of 20,000, show a primary vortex shedding frequency of 8.0Hz and a dimple edge vortex pair oscillation frequency of approximately 6.5Hz. The local flow structure shows some qualitative similarity to characteristics measured with deeper dimples (δ∕D of 0.2 and 0.3), with smaller quantitative changes from the dimples as δ∕D decreases. A similar conclusion is reached regarding qualitative and quantitative variations of local Nusselt number ratio data, which show that the highest local values are present within the downstream portions of dimples, as well as near dimple spanwise and downstream edges. Local and spatially averaged Nusselt number ratios sometimes change by small amounts as the channel inlet turbulence intensity level is altered, whereas friction factor ratios increase somewhat at the channel inlet turbulence intensity level increases. These changes to local Nusselt number data (with changing turbulence intensity level) are present at the same locations where the vortex pairs appear to originate, where they have the greatest influences on local flow and heat transfer behavior.

Latticework (Vortex) Cooling Effectiveness: Part 2 — Rotating Channel Experiments

2004 ◽  
Author(s):  
S. Acharya ◽  
Fuguo Zhou ◽  
Jonathan Lagrone ◽  
Gazi Mahmood ◽  
Ronald S. Bunker
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Density Ratio ◽  
Transfer Coefficients ◽  
Performance Factors ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Smooth Channel ◽  
Rib Turbulators ◽  
Density Ratios

The heat transfer and pressure drop characteristics of latticework coolant blade passages have been investigated experimentally under conditions of rotation. Stationary studies with the latticework configuration have shown potential advantages including spatially-uniform streamwise distributions of the heat transfer coefficient, greater blade strength, and enhancement levels comparable to conventional rib turbulators. In the present study, a latticework coolant passage, with orthogonal-ribs, is studied in a rotating heat transfer test-rig for a range of Reynolds numbers (Res), Rotation numbers (Ros), and density ratios. Measurements indicate that for Res≥20,000, the latticework coolant passage provides very uniform streamwise distributions of the Nusselt number (Nus) with enhancement levels (relative to smooth-channel values) in the range of 2.0 to 2.5. No significant dependence of Nus on Ros and density ratio is observed except at lower Res values (≤10,000). Nusselt numbers are highest immediately downstream of a turn indicating that bend-effects play a major role in enhancing heat transfer. Friction factors are relatively insensitive to Ros, and thermal performance factors at higher Res values appear to be comparable to those obtained with conventional rib-turbulators. The present study indicates that latticework cooling geometry can provide comparable heat transfer enhancements and thermal performance factors as conventional rib-turbulators, with potential benefits of streamwise uniformity in the heat transfer coefficients and added blade strength.

Local Heat Transfer and Flow Structure on and Above a Dimpled Surface in a Channel

2000 ◽  
Vol 123 (1) ◽  
pp. 115-123 ◽  
Author(s):  
G. I. Mahmood ◽  
M. L. Hill ◽  
D. L. Nelson ◽  
P. M. Ligrani ◽  
H.-K. Moon ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Surface Temperature ◽  
Local Heat Transfer ◽  
Streamwise Velocity ◽  
Test Surface ◽  
Channel Height ◽  
Stagnation Temperature ◽  
Vortex Pairs ◽  
Nusselt Numbers ◽  
Flow Visualizations

Experimental results, measured on and above a dimpled test surface placed on one wall of a channel, are given for Reynolds numbers from 1250 to 61,500 and ratios of air inlet stagnation temperature to surface temperature ranging from 0.68 to 0.94. These include flow visualizations, surveys of time-averaged total pressure and streamwise velocity, and spatially resolved local Nusselt numbers, which are measured using infrared thermography, used in conjunction with energy balances, thermocouples, and in situ calibration procedures. The ratio of channel height to dimple print diameter is 0.5. Flow visualizations show vortical fluid and vortex pairs shed from the dimples, including a large upwash region and packets of fluid emanating from the central regions of each dimple, as well as vortex pairs and vortical fluid that form near dimple diagonals. These vortex structures augment local Nusselt numbers near the downstream rims of each dimple, both slightly within each depression, and especially on the flat surface just downstream of each dimple. Such augmentations are spread over larger surface areas and become more pronounced as the ratio of inlet stagnation temperature to local surface temperature decreases. As a result, local and spatially averaged heat transfer augmentations become larger as this temperature ratio decreases. This is due to the actions of vortical fluid in advecting cool fluid from the central parts of the channel to regions close to the hotter dimpled surface.

Nusselt Numbers and Flow Structure On and Above a Shallow Dimpled Surface Within a Channel Including Effects of Inlet Turbulence Intensity Level

2004 ◽  
Author(s):  
P. M. Ligrani ◽  
N. K. Burgess ◽  
S. Y. Won
Keyword(s):  
Nusselt Number ◽  
Flow Structure ◽  
Turbulence Intensity ◽  
Local Nusselt Number ◽  
Channel Height ◽  
Intensity Level ◽  
Stagnation Temperature ◽  
Channel Inlet ◽  
Local Flow ◽  
Nusselt Numbers

Experimental results from a channel with shallow dimples placed on one wall are given for Reynolds numbers based on channel height from 3,700 to 20,000, levels of longitudinal turbulence intensity from 3 to 11 percent (at the entrance of the channel test section), and a ratio of air inlet stagnation temperature to surface temperature of approximately 0.94. The ratio of dimple depth to dimple print diameter δ/D is 0.1, and the ratio of channel height to dimple print diameter H/D is 1.00. The data presented include friction factors, local Nusselt numbers, spatially-averaged Nusselt numbers, a number of time-averaged flow structural characteristics, and spectra of longitudinal velocity fluctuations which, at a Reynolds number of 20,000, show a primary vortex shedding frequency of 8.0 Hz and a dimple edge vortex pair oscillation frequency of approximately 6.5 Hz. Local flow structure shows some qualitative similarity to characteristics measured with deeper dimples (δ/D of 0.2 and 0.3), with smaller quantitative changes from the dimples as δ/D decreases. A similar conclusion is reached regarding qualitative and quantitative variations of local Nusselt number ratio data, which show that the highest local values are present within the downstream portions of dimples, as well as near dimple spanwise and downstream edges. Local and spatially-averaged Nusselt number ratios sometimes change by small amounts as the channel inlet turbulence intensity level is altered, whereas friction factor ratios increase somewhat at the channel inlet turbulence intensity level increases. These changes to local Nusselt number data (with changing turbulence intensity level) are present at the same locations where the vortex pairs appear to originate, and have the greatest influences on local flow and heat transfer behavior.

Latticework (Vortex) Cooling Effectiveness: Rotating Channel Experiments

2004 ◽  
Vol 127 (3) ◽  
pp. 471-478 ◽  
Author(s):  
S. Acharya ◽  
F. Zhou ◽  
J. Lagrone ◽  
G. Mahmood ◽  
R. S. Bunker
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Density Ratio ◽  
Transfer Coefficients ◽  
Performance Factors ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Smooth Channel ◽  
Rib Turbulators ◽  
Density Ratios

The heat transfer and pressure drop characteristics of latticework coolant blade passages have been investigated experimentally under conditions of rotation. Stationary studies with the latticework configuration have shown potential advantages including spatially-uniform streamwise distributions of the heat transfer coefficient, greater blade strength, and enhancement levels comparable to conventional rib turbulators. In the present study, a latticework coolant passage, with orthogonal-ribs, is studied in a rotating heat transfer test-rig for a range of Reynolds numbers (Res), Rotation numbers (Ros), and density ratios. Measurements indicate that for Res⩾20,000, the latticework coolant passage provides very uniform streamwise distributions of the Nusselt number (Nus) with enhancement levels (relative to smooth-channel values) in the range of 2.0–2.5. No significant dependence of Nus on Ros and density ratio is observed except at lower Res values (⩽10,000). Nusselt numbers are highest immediately downstream of a turn indicating that bend-effects play a major role in enhancing heat transfer. Friction factors are relatively insensitive to Ros, and thermal performance factors at higher Res values appear to be comparable to those obtained with conventional rib-turbulators. The present study indicates that latticework cooling geometry can provide comparable heat transfer enhancements and thermal performance factors as conventional rib-turbulators, with potential benefits of streamwise uniformity in the heat transfer coefficients and added blade strength.

Nusselt Number Behavior on Deep Dimpled Surfaces Within a Channel

2002 ◽  
Author(s):  
N. K. Burgess ◽  
M. M. Oliveira ◽  
P. M. Ligrani
Keyword(s):  
Nusselt Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Test Surface ◽  
Channel Height ◽  
Stagnation Temperature ◽  
Spatially Resolved ◽  
Nusselt Numbers ◽  
Air Inlet

Experimental results, measured on a dimpled test surface placed on one wall of a channel, are given for a ratio of air inlet stagnation temperature to surface temperature of approximately 0.94, and Reynolds numbers from 12,000 to 70,000. These data include friction factors, local Nusselt numbers, spatially-resolved local Nusselt numbers, and globally-averaged Nusselt numbers. The ratio of dimple depth to dimple print diameter δ/D is 0.3, and the ratio of channel height to dimple print diameter is 1.00. These results are compared to measurements from other investigations with different ratios of dimple depth to dimple print diameter δ/D to provide information on the influences of dimple depth. At all Reynolds numbers considered, local and spatially-resolved Nusselt number augmentations increase as dimple depth increases (and all other experimental and geometric parameters are held approximately constant). These are attributed to: (i) increases in the strengths and intensity of vortices and associated secondary flows ejected from the dimples, as well as (ii) increases in the magnitudes of three-dimensional turbulence production and turbulence transport. The effects of these phenomena are especially apparent in local Nusselt number ratio distributions measured just inside of the dimples, and just downstream of the downstream edges of the dimples.

Sign in / Sign up

Export Citation Format

Share Document